ABSTRACT
BACKGROUND: To prevent the absorption and collapse of the labial bone plate of the anterior teeth, immediate implantation and socket shield technique have been increasingly applied to anterior dental aesthetic implant restoration. OBJECTIVE: To provide a biomechanical basis for implant restoration of maxillary anterior teeth, finite element analysis was used to investigate the stress peak and distribution in different anatomical sites of natural teeth, conventional immediate implantation and socket shield technique. METHODS: Three maxillary finite element models were established, including a maxillary incisor as a natural tooth, a conventional immediate implantation and a socket shield technique. A mechanical load of 100â¯N was applied to simulate and analyze the biomechanical behavior of the root, periodontal ligament (PDL), implant and surrounding bone interface. RESULTS: The stress distribution of the natural tooth was relatively uniform under load. The maximum von Mises stress of the root, periodontal ligament, cortical bone and cancellous bone were 20.14â¯MPa, 2.473â¯MPa, 19.48â¯MPa and 5.068â¯MPa, respectively. When the conventional immediate implantation was loaded, the stress was mainly concentrated around the neck of implant. Maximum stress on the surface of the implant was 102â¯MPa, the cortical bone was 16.13â¯MPa, and the cancellous bone was 18.29â¯MPa. When the implantation with socket shield technique was loaded, the stress distribution of the implant was similar to that of immediate implantation. Maximum stress on the surface of the implant was 100.5â¯MPa, the cortical bone was 23.11â¯MPa, the cancellous bone was 21.66â¯MPa, the remaining tooth fragment was 29.42â¯MPa and the periodontal ligament of the tooth fragment was 1.131â¯MPa. CONCLUSIONS: 1. Under static loading, both socket shield technology and conventional immediate implantation can support the esthetic restoration of anterior teeth biomechanically. 2.Under short-term follow-up, both immediate implant and socket shield technology achieved satisfactory clinical results, including bone healing and patient satisfaction. 3.The stress distribution is mainly located on the buccal bone surface of the implant and is associated with resorption of the buccal bone plate after implant replacement in both socket shield technology and conventional immediate implantation. 4.The presence of retained root fragment had an impact on the bone graft gap. In immediate implantation, the peak stress was located in the cortical bone near the implant position, while in socket shield technology, the peak stress was at the neck of the cortical bone corresponding to the retained root fragment.
ABSTRACT
BACKGROUND: With periodontal disease having an increasing incidence, mandibular free-end edentulism caused by periodontitis is clinically more common. Finite element analysis and clinical case reports were used to evaluate the influence of different designs on the load distribution of implant prosthesis in mandibular posterior free-end edentulism. METHOD: A finite element model of a mandible with posterior free-end edentulism was established. Considering the implant position and selection of single crown repair or splint repair, four designs were conducted including model A: 3435 × 37(four-unit fixed bridge supported by three implants, implant positions were 34, 35, 37); model B: 34,35 × 37, (34: a single implant crown) (35 ×37: three-unit fixed bridge supported by two implants, implant positions were 35, 37); model C: 34 × 3637(four-unit fixed bridge supported by three implants, implant positions were 34, 36, 37); and model D: 34 × 36, 37(37: a single implant crown)(34 ×36: three-unit fixed bridge supported by two implants, implant positions were 34, 36). Stress distribution and the Von Mises stress value of the implants, the crown and the bone around the implants were analyzed at vertical and 45° inclined load. RESULTS: Stress in the cortical bone was mainly concentrated around the implant neck, and maximum Von Mises stress (MVMS) of the four models was 11.6-16.1 MPa at vertical load and 61.74-96.49 MPa at 45° inclined load. Stress in the cancellous bone was concentrated around the implant base, and MVMS of four models was 3.075-3.899 MPa at vertical load and 5.021-6.165 MPa at 45° inclined load. Stress of the restoration crowns was mainly concentrated in the connector of the bridge, and MVMS of four models was 23.38-26.28 MPa at vertical load and 53.14-56.35 MPa at 45° inclined load. Stress of the implant interface was mainly concentrated on the surface of the smaller implants near the bridge, and MVMS of four models was 21.12-33.25 MPa at vertical load and 83.73-138.7 MPa at 45° inclined load. CONCLUSION: There was favorable stress distribution of the four models at vertical load and 45° inclined load. Design of a three-unit fixed bridge combined with a partial crown may be an available option for devising patient treatment plans with mandibular free-end edentulism.