The impact of wastewater matrix on the degradation of pharmaceutically active compounds by oxidation processes including ultraviolet radiation and sulfate radicals.

Ultraviolet radiation (UV)-activated peroxydisulfate (PDS) and peroxymonosulfate (PMS) advanced oxidation processes were examined for their capacity to remove nine pharmaceutically active compounds (PhACs) from secondary effluent. The effect of operational parameters (initial oxidant concentration, UV exposure time, pH, common coexisting anions and effluent organic matter (EfOM)) on UV/PDS and UV/PMS treatment efficiency was investigated in a collimated beam device housing a low-pressure mercury UV lamp emitting light at 253.7 nm. Both AOPs achieved high removals (>90%) when applied to pure water. Under otherwise similar conditions the removal percentage fell by 20-30% due to the scavenging of effluent organic matter (EfOM) in secondary effluent. Finally, eliminating EfOM but maintaining the inorganic composition, the radical scavenging effect was reduced and 98.3% and 85.6% average removals were obtained by UV/PDS and UV/PMS, respectively. Increasing pH improved degradation of several PhACs containing amine groups. Higher oxidant dosages created only a significant benefit in UV/PDS. The chloride anion produced a negligible effect on both processes, while higher nitrate concentrations increased removal percentage but did not affect degradation rate constants. Finally and surprisingly, the addition of bicarbonate had the strongest positive impact on the degradation kinetics observed, even stronger than the elimination of EfOM from secondary effluent.

Evaluating the application of Microbacterium sp. strain BR1 for the removal of sulfamethoxazole in full-scale membrane bioreactors.

Microbacterium sp. strain BR1 is a bacterial strain that recently received attention for its capability to mineralize sulfamethoxazole (SMX) and other sulfonamides. In this study, the survival of Microbacterium sp. in municipal sludge waters was tested in batch experiments to explore optimal process conditions. Inoculation of Microbacterium sp. was subsequently performed in a pilot membrane bioreactor (MBR) operated in two configurations: treating full-scale MBR permeate (post-treatment) and treating raw municipal wastewater. SMX removal by Microbacterium sp. could not be proved in any of the configurations, except for SMX concentrations far higher than the ones normally found in municipal wastewater. By use of molecular tools (fluorescence in situ hybridization analysis) a low capability to survive in activated sludge systems was assessed. After inoculation, Microbacterium sp. was reduced to a small fraction of the viable biomass. The observed growth rate appeared to be many times lower than the one of typical activated sludge micro-organisms. Possibilities of application in full-scale municipal wastewater treatment are scarce.

Membrane bioreactor (MBR) sludge inoculation in a hybrid process scheme concept to assist overloaded conventional activated sludge (CAS) process operations.

This study analyzes the effect of inoculating membrane bioreactor (MBR) sludge in a parallel-operated overloaded conventional activated sludge (CAS) system. Modelling studies that showed the beneficial effect of this inoculation were confirmed though full scale tests. Total nitrogen (TN) removal in the CAS increased and higher nitrate formation rates were achieved. During MBR sludge inoculation, the TN removal in the CAS was proven to be dependent on MBR sludge loading. Special attention was given to the effect of inoculation on sludge quality. The MBR flocs, grown without selection pressure, were clearly distinct from the more compact flocs in the CAS system and also contained more filamentous bacteria. After inoculation the MBR flocs did not evolve into good-settling compact flocs, resulting in a decreasing sludge quality. During high flow conditions the effluent CAS contained more suspended solids. Sludge volume index, however, did not increase. Laboratory tests were held to determine the threshold volume of MBR sludge to be seeded into the CAS reactor. Above 16-30%, supernatant turbidity and scum formation increased markedly.

Cost optimisation and minimisation of the environmental impact through life cycle analysis of the waste water treatment plant of Bree (Belgium).

An ASM2da model of the full-scale waste water plant of Bree (Belgium) has been made. It showed very good correlation with reference operational data. This basic model has been extended to include an accurate calculation of environmental footprint and operational costs (energy consumption, dosing of chemicals and sludge treatment). Two optimisation strategies were compared: lowest cost meeting the effluent consent versus lowest environmental footprint. Six optimisation scenarios have been studied, namely (i) implementation of an online control system based on ammonium and nitrate sensors, (ii) implementation of a control on MLSS concentration, (iii) evaluation of internal recirculation flow, (iv) oxygen set point, (v) installation of mixing in the aeration tank, and (vi) evaluation of nitrate setpoint for post denitrification. Both an environmental impact or Life Cycle Assessment (LCA) based approach for optimisation are able to significantly lower the cost and environmental footprint. However, the LCA approach has some advantages over cost minimisation of an existing full-scale plant. LCA tends to chose control settings that are more logic: it results in a safer operation of the plant with less risks regarding the consents. It results in a better effluent at a slightly increased cost.

Activated sludge model (ASM) based modelling of membrane bioreactor (MBR) processes: a critical review with special regard to MBR specificities.

Membrane bioreactors (MBRs) have been increasingly employed for municipal and industrial wastewater treatment in the last decade. The efforts for modelling of such wastewater treatment systems have always targeted either the biological processes (treatment quality target) as well as the various aspects of engineering (cost effective design and operation). The development of Activated Sludge Models (ASM) was an important evolution in the modelling of Conventional Activated Sludge (CAS) processes and their use is now very well established. However, although they were initially developed to describe CAS processes, they have simply been transferred and applied to MBR processes. Recent studies on MBR biological processes have reported several crucial specificities: medium to very high sludge retention times, high mixed liquor concentration, accumulation of soluble microbial products (SMP) rejected by the membrane filtration step, and high aeration rates for scouring purposes. These aspects raise the question as to what extent the ASM framework is applicable to MBR processes. Several studies highlighting some of the aforementioned issues are scattered through the literature. Hence, through a concise and structured overview of the past developments and current state-of-the-art in biological modelling of MBR, this review explores ASM-based modelling applied to MBR processes. The work aims to synthesize previous studies and differentiates between unmodified and modified applications of ASM to MBR. Particular emphasis is placed on influent fractionation, biokinetics, and soluble microbial products (SMPs)/exo-polymeric substances (EPS) modelling, and suggestions are put forward as to good modelling practice with regard to MBR modelling both for end-users and academia. A last section highlights shortcomings and future needs for improved biological modelling of MBR processes.