ABSTRACT
The food industry has grown with the demands for new products and their authentication, which has not been accompanied by the area of analysis and quality control, thus requiring novel process analytical technologies for food processes. An electronic tongue (e-tongue) is a multisensor system that can characterize complex liquids in a fast and simple way. Here, we tested the efficacy of an impedimetric microfluidic e-tongue setup - comprised by four interdigitated electrodes (IDE) on a printed circuit board (PCB), with four pairs of digits each, being one bare sensor and three coated with different ultrathin nanostructured films with different electrical properties - in the analysis of fresh and industrialized coconut water. Principal Component Analysis (PCA) was applied to observe sample differences, and Partial Least Squares Regression (PLSR) was used to predict sample physicochemical parameters. Linear Discriminant Analysis (LDA) and Partial Least Square - Discriminant Analysis (PLS-DA) were compared to classify samples based on data from the e-tongue device. Results indicate the potential application of the microfluidic e-tongue in the identification of coconut water composition and determination of physicochemical attributes, allowing for classification of samples according to soluble solid content (SSC) and total titratable acidity (TTA) with over 90% accuracy. It was also demonstrated that the microfluidic setup has potential application in the food industry for quality assessment of complex liquid samples.
Subject(s)
Cocos , Dielectric Spectroscopy , Principal Component Analysis , Cocos/chemistry , Least-Squares Analysis , Dielectric Spectroscopy/methods , Discriminant Analysis , Water/chemistry , Food Analysis/methods , Microfluidics/methods , Microfluidics/instrumentation , Electronic NoseABSTRACT
Artisanal cheeses are part of the heritage and identity of different countries or regions. In this work, we investigated the spectral variability of a wide range of traditional Brazilian cheeses and compared the performance of different spectrometers to discriminate cheese types and predict compositional parameters. Spectra in the visible (vis) and near infrared (NIR) region were collected, using imaging (vis/NIR-HSI and NIR-HSI) and conventional (NIRS) spectrometers, and it was determined the chemical composition of seven types of cheeses produced in Brazil. Principal component analysis (PCA) showed that spectral variability in the vis/NIR spectrum is related to differences in color (yellowness index) and fat content, while in NIR there is a greater influence of productive steps and fat content. Partial least squares discriminant analysis (PLSDA) models based on spectral information showed greater accuracy than the model based on chemical composition to discriminate types of traditional Brazilian cheeses. Partial least squares (PLS) regression models based on vis/NIR-HSI, NIRS, NIR-HSI data and HSI spectroscopic data fusion (vis/NIR + NIR) demonstrated excellent performance to predict moisture content (RPD > 2.5), good ability to predict fat content (2.0 < RPD < 2.5) and can be used to discriminate between high and low protein values (â¼1.5 < RPD < 2.0). The results obtained for imaging and conventional equipment are comparable and sufficiently accurate, so that both can be adapted to predict the chemical composition of the Brazilian traditional cheeses used in this study according to the needs of the industry.
Subject(s)
Cheese , Hyperspectral Imaging , Principal Component Analysis , Spectroscopy, Near-Infrared , Cheese/analysis , Spectroscopy, Near-Infrared/methods , Hyperspectral Imaging/methods , Brazil , Discriminant Analysis , Least-Squares Analysis , ColorABSTRACT
Artisanal cheeses are highly valued around the world for their distinct sensory characteristics, thus being prone to adulteration by substituting authentic material for cheaper products, such as vegetable oil. In this work, we developed a method based on a portable NIR spectrometer as a non-destructive and low-cost alternative to identify adulteration in butter cheese. Dataset consisted of authentic and intentionally adulterated cheeses in the laboratory and commercial cheeses, which were identified as authentic and adulterated with vegetable oil after analysis of the fatty acid profile. PLS-DA classification models identified adulterated samples with an accuracy of 94.44%. PLS prediction models showed excellent performance (RPD > 3.0) to predict the adulterant level. These results demonstrate that NIR spectra can be used to identify the replacement of authentic fat by soybean oil in butter cheese and that the developed models can be used to identify adulteration in external samples with good performance.
Subject(s)
Butter , Cheese , Butter/analysis , Cheese/analysis , Chemometrics , Plant Oils/analysis , Soybean Oil/analysis , Food Contamination/analysis , Least-Squares AnalysisABSTRACT
Ingredients added in food products can increase the nutritional value, but also affect their functional properties. After processing, determination of added ingredients is difficult, thus it is important to develop rapid techniques for quantification of food ingredients. In the current work, near infrared spectroscopy (NIRS) and hyperspectral imaging (NIR-HSI) were investigated to quantify the amount of fiber added to semolina and its distribution. NIR spectra were acquired to compare the accuracy in the classification, quantification and distribution of fibers added to semolina. Principal Component Analyses (PCA) and Soft Independent Modeling of Class Analogy (SIMCA) were used for classification. Partial Least Squares Regression (PLSR) models applied to NIR-HSI spectra showed R2P between 0.85 and 0.98, and RMSEP between 0.5 and 1%, and were used for prediction map of the samples. These results showed that NIR-HSI technique can be used for the identification and quantification of fiber added to semolina.