ABSTRACT
13 C nuclear magnetic resonance (NMR) is traditionally considered an insensitive technique, requiring long acquisition times to measure dilute functionalities on large polymers. With the introduction of cryoprobes and better electronics, sensitivity has improved in a way that allows measurements to take less than 1/20th the time that they previously did. Unfortunately, a high Q-factor with cryoprobes creates baseline curvature related to acoustic ringing that affects quantitative NMR analyses. Manual baseline correction is commonly used to compensate for the baseline roll, but it is a time-intensive process. The outcome of manual baseline correction can vary depending on processing parameters, especially for complicated spectra. Additionally, it can be challenging to distinguish between broad peaks and baseline rolls. A new anti-ring pulse sequence (zgig_pisp) was previously reported to improve on the incumbent single pulse experiment (zgig). The original report presented limited comparison data with 13 C NMR, but a thorough validation is needed before broader implementation can be considered. In this work, we report the round-robin testing and comparison of zgig_pisp and zgig pulse sequences. During the testing phase, we found that zgig_pisp is practically equivalent to zgig to ±2% for the majority of integrals examined. Additionally, a short broadband inversion pulse (BIP) was demonstrated as an alternative to the originally reported adiabatic CHIRP shaped pulse. The zgig_pisp pulse sequence code for Bruker spectrometers is also simplified.
ABSTRACT
Silicone-polyether (SPE) surfactants, made of a polydimethyl-siloxane (PDMS) backbone and polyether branches, are commonly used as additives in the production of polymeric foams with improved properties. A key step in the production of polymeric foams is the nucleation of gas bubbles in the polymer matrix upon supersaturation of dissolved gas. However, the role of SPE surfactants in the nucleation of gas bubbles is not well understood. In this study, we use classical density functional theory to investigate the effect of an SPE surfactant on the nucleation of CO2 bubbles in a polyol foam formulation. We find that the addition of an SPE surfactant leads to a â¼3-fold decrease in the polyol-CO2 interfacial tension at the surfactant's critical micelle concentration. Additionally, the surfactant is found to reduce the free energy barrier and affect the minimum free energy pathway (MFEP) associated with CO2 bubble nucleation. In the absence of a surfactant, a CO2-rich bubble nucleates from a homogeneous CO2-supersaturated polyol solution by following an MFEP characterized by a single nucleation barrier. Adding a surfactant results in a two-step nucleation process with reduced free energy barriers. The first barrier corresponds to the formation of a spherical aggregate with a liquid-like CO2 core. This spherical aggregate then grows into a CO2-rich bubble (spherical aggregate with a vapor-like CO2 core) of a critical size representing the second barrier. We hypothesize that the stronger affinity of CO2 for PDMS (than polyether) stabilizes the spherical aggregate with the liquid-like CO2 core, leading to a lower free energy barrier for CO2 bubble nucleation. Stabilization of such an aggregate during the early stages of the nucleation may lead to foams with more, smaller bubbles, which can improve their microstrustural features and insulating abilities.
ABSTRACT
In carbon dioxide-blown polymer foams, the solubility of carbon dioxide (CO2) in the polymer profoundly shapes the structure and, consequently, the physical properties of the foam. One such foam is polyurethane-commonly used for thermal insulation, acoustic insulation, and cushioning-which increasingly relies on CO2 to replace environmentally harmful blowing agents. Polyurethane is produced through the reaction of isocyanate and polyol, of which the polyol has the higher capacity for dissolving CO2. While previous studies have suggested the importance of the effect of hydroxyl end groups on CO2 solubility in short polyols (<1000 g/mol), their effect in polyols with higher molecular weight (≥1000 g/mol) and higher functionality (>2 hydroxyls per chain)-as are commonly used in polyurethane foams-has not been reported. Here, we show that the solubility of CO2 in polyether polyols decreases with molecular weight above 1000 g/mol and decreases with functionality using measurements performed by gravimetry-axisymmetric drop-shape analysis. The nonmonotonic effect of molecular weight on CO2 solubility results from the competition between effects that reduce CO2 solubility (lower mixing entropy) and effects that increase CO2 solubility (lower ratio of hydroxyl end groups to ether backbone groups). To generalize our measurements, we modeled the CO2 solubility using a perturbed chain-statistical associating fluid theory (PC-SAFT) model, which we validated by showing that a density functional theory model based on the PC-SAFT free energy accurately predicted the interfacial tension.
ABSTRACT
Polyvinyl polymers bearing pendant hole transport functionalities have been extensively explored for solution-processed hole transport layer (HTL) technologies, yet there are only rare examples of high anisotropic packing of the HT moieties of these polymers into substrate-parallel orientations within HTL films. For small molecules, substrate-parallel alignment of HT moieties is a well-established approach to improve overall device performance. To address the longstanding challenge of extension from vapor-deposited small molecules to solution-processable polymer systems, a fundamental chemistry tactic is reported here, involving the positioning of HT side chains within macromolecular frameworks by the construction of HT polymers having bottlebrush topologies. Applying state-of-the-art polymer synthetic techniques, various functional subunits, including triphenylamine (TPA) for hole transport and adhesion to the substrate, and perfluoro alkyl-substituted benzyloxy styrene for migration to the air interface, were organized with exquisite control over the composition and placement throughout the bottlebrush topology. Upon assembling the HT bottlebrush (HTB) polymers into monolayered HTL films on various substrates through spin-casting and thermal annealing, the backbones of HTBs were vertically aligned while the grafts with pendant TPAs were extended parallel to the substrate. The overall design realized high TPA π-stacking along the out-of-plane direction of the substrate in the HTLs, which doubled the efficiency of organic light-emitting diodes compared with linear poly(vinyl triphenylamine)s.
ABSTRACT
In the next decade, separation science will be an important research topic in addressing complex challenges like reducing carbon footprint, lowering energy cost, and making industrial processes simpler. In industrial chemical processes, particularly in petrochemical operations, separation and product refining steps are responsible for up to 30% of energy use and 30% of the capital cost. Membranes and adsorption technologies are being actively studied as alternative and partial replacement opportunities for the state-of-the-art cryogenic distillation systems. This paper provides an industrial perspective on the application of membranes in industrial petrochemical cracker operations. A gas separation performance figure of merit for propylene/propane separation for different classes of materials ranging from inorganic, carbon, polymeric, and facilitated transport membranes is also reported. An in-house-developed model provided insights into the importance of operational parameters on the overall membrane design.
ABSTRACT
This study reports 6FDA:BPDA-DAM polyimide-derived hollow fiber carbon molecular-sieve (CMS) membranes for hydrogen and ethylene separation. Since H2 /C2 H4 selectivity is the lowest among H2 /(C1 -C3 ) hydrocarbons, an optimized CMS fiber for this gas pair is useful for removing hydrogen from all-cracked gas mixtures. A process we term hyperaging provides highly selective CMS fiber membranes by tuning CMS ultramicropores to favor H2 over larger molecules to give a H2 /C2 H4 selectivity of over 250. Hyperaging conditions and a hyperaging mechanism are discussed in terms of an expedited physical aging process, which is largely controlled by the hyperaging temperature. For the specific CMS material considered here, a hyperaging temperature beyond 90 °C but less than 250 °C works best. Hyperaging also stabilizes CMS materials against physical aging and stabilizes the performance of H2 separation over extended periods. This work opens a door in the development of CMS materials for the separation of small molecules from large molecules.
ABSTRACT
The ability to manipulate a single quantum object, such as a single electron or a single spin, to induce a change in a macroscopic observable lies at the heart of nanodevices of the future. We report an experiment wherein a single superconducting flux quantum, or a fluxon, can be exploited to switch the resistance of a nanowire between two discrete values. The experimental geometry consists of centimeter-long nanowires of superconducting Ga-In eutectic, with spontaneously formed Ga nanodroplets along the length of the nanowire. The nonzero resistance occurs when a Ga nanodroplet traps one or more superconducting fluxons, thereby driving a Josephson weak-link created by a second nearby Ga nanodroplet normal. The fluxons can be inserted or flipped by careful manipulation of the magnetic field or temperature to produce one of many metastable states of the system.
ABSTRACT
Low-dimensional carbon nanomaterials such as fullerenes, nanotubes, graphene and diamondoids have extraordinary physical and chemical properties. Compression-induced polymerization of aromatic molecules could provide a viable synthetic route to ordered carbon nanomaterials, but despite almost a century of study this approach has produced only amorphous products. Here we report recovery to ambient pressure of macroscopic quantities of a crystalline one- dimensional sp(3) carbon nanomaterial formed by high-pressure solid-state reaction of benzene. X-ray and neutron diffraction, Raman spectroscopy, solid-state NMR, transmission electron microscopy and first-principles calculations reveal close- packed bundles of subnanometre-diameter sp(3)-bonded carbon threads capped with hydrogen, crystalline in two dimensions and short-range ordered in the third. These nanothreads promise extraordinary properties such as strength and stiffness higher than that of sp(2) carbon nanotubes or conventional high-strength polymers. They may be the first member of a new class of ordered sp(3) nanomaterials synthesized by kinetic control of high-pressure solid-state reactions.
ABSTRACT
In situ high-pressure Raman spectroscopy, with corroborating density functional calculations, is used to probe C-H chemical bonds formed when dissociated hydrogen diffuses from a platinum nanocatalyst to three distinct graphenic surfaces. At ambient temperature, hydrogenation and dehydrogenation are reversible in the combined presence of an active catalyst and oxygen heteroatoms. Hydrogenation apparently occurs through surface diffusion in a chemisorbed state, while dehydrogenation requires diffusion of the chemisorbed species back to an active catalyst.