Global Vision of the Reaction and Deactivation Routes in the Ethanol Steam Reforming on a Catalyst Derived from a Ni-Al Spinel.

Ethanol steam reforming (ESR) over a Ni/Al2O3 catalyst prepared by reduction of a NiAl2O4 spinel is a promising alternative route to produce H2 from biomass. This work deepens into the effect of reaction conditions (450-650 °C, a steam/ethanol (S/E) ratio of 3-9, and a weight space time up to 1.3 h) and evaluates the time on stream evolution of the yields of H2, gaseous byproducts (CO, CO2, CH4, C2H4, C2H4O), and formed carbon/coke. The results are explained taking into consideration the thermodynamics, the extent of each individual reaction, and the catalyst deactivation. Up to 600 °C, the predominant intermediate in the H2 formation is C2H4 (formed by ethanol dehydration) with the preferential formation of nanostructured carbon (nanotubes/filaments) by C2H4 decomposition. The deposition of this type of carbon partially deactivates the catalyst, mainly affecting the extent of the C2H4 decomposition causing a sharp decrease in the H2 and carbon yields. Nevertheless, the catalyst reaches a pseudosteady state with an apparent constant activity for other reactions in the kinetic scheme. At 650 °C, C2H4O (formed by the ethanol dehydrogenation) is the main intermediate in the H2 formation, which is the precursor of an amorphous/turbostratic carbon (coke) formation that initially causes a rapid deactivation of the catalyst, affecting the ethanol dehydration and, to a lower extent, the reforming and water gas shift reactions. The increase in the S/E ratio favors the H2 formation, attenuates the catalyst deactivation due to the suppression of the ethanol dehydration to C2H4, and promotes the reforming, water gas shift, and carbon/coke gasification reactions. A H2 yield of 85% stable for 48 h on stream is achieved at 600 °C, with a space time of 0.1 h and an S/E ratio of 9.

Insights into the Reaction Routes for H2 Formation in the Ethanol Steam Reforming on a Catalyst Derived from NiAl2O4 Spinel.

This work describes the satisfactory performance of a Ni/Al2O3 catalyst derived from NiAl2O4 spinel in ethanol steam reforming and focuses on studying the prevailing reaction routes for H2 formation in this system. NiAl2O4 spinel was synthesized using a coprecipitation method and reduced at 850 °C to obtain a Ni/Al2O3 catalyst. The spinel structure and catalyst were characterized using XRD, TPR, N2 physisorption, NH3 adsorption and TPD, TPO, SEM, and TEM. The experiments were carried out in a fluidized-bed reactor at 500 or 600 °C and different space-time values, using pure ethanol, ethanol-water, pure ethylene, or ethylene-water feeds. The reaction takes place through two paired routes activated by each catalyst function (metal and acid sites) whose extent is limited by the selective catalyst deactivation. The results evidence that at the beginning of the reaction the main route for the formation of H2 and carbon (nanotubes) is the dehydration of ethanol on acid sites followed by decomposition of ethylene on the Ni-Al2O3 interface. This route is favored at 500 °C. After the rapid deactivation of the catalyst for ethylene decomposition, the route of H2 formation by steam reforming of ethanol and water gas shift reactions over Ni sites is favored. The morphology of the carbon deposits (nanotubes) allows the catalyst to maintain a notable activity for the latter pathways, with stable formation of H2 (during 48 h in the experiments carried out). At 600 °C, the extent of the gasification reaction of carbon species lowers the carbon material formation. The high formation of carbon material is interesting for the coproduction of H2 and carbon nanotubes with low CO2 emissions.

Compositional insights and valorization pathways for carbonaceous material deposited during bio-oil thermal treatment.

This work analyses the composition, morphology, and thermal behavior of the carbonaceous materials deposited during the thermal treatment of bio-oil (thermal pyrolytic lignin-TPL). The bio-oil was obtained by flash pyrolysis of lignocellulosic biomass (pine sawdust), and the TPLs were obtained in the 400-700 °C range. The TPLs were characterized by performing elemental analysis; (13)C NMR, Raman, FTIR, and X-ray photoelectron spectroscopy; SEM; and temperature-programmed oxidation analyzed by differential thermogravimetry and differential scanning calorimetry. The results are compared to a commercial lignin (CL). The TPLs have lower oxygen and hydrogen contents and a greater aromaticity and structural order than the CL material. Based on these features, different valorization routes are proposed: the TPL obtained at 500 °C is suitable for use as a fuel, and the TPL obtained at 700 °C has a suitable morphology and composition for use as an adsorbent or catalyst support.