Micropatterning of polymer brushes: grafting from dewetting polymer films for biological applications.

In this novel platform, a micropatterned polymer brush was obtained by grafting poly(poly(ethylene glycol) methyl ether methacrylate) (poly(PEGMA)) from a thin macroinitiator film using atom transfer radical polymerization (ATRP). A pattern of holes was formed in the macroinitiator film by taking advantage of its spontaneous dewetting above the glass transition temperature from a bottom polystyrene film, driven by unfavorable intermolecular forces. Patterning by dewetting can be achieved at length-scales from a few hundred nanometers to several tens of micrometers, by simply thermally annealing the bilayer above the glass transition temperature of the polymer. This approach is substrate-independent, as polymer films can be cast onto surfaces of different size, shape, or material. As a demonstration of its potential, proteins, and individual cells were attached on targeted bioadhesive polystyrene areas of the micropatterns within poly(PEGMA) protein-repellent brushes. We anticipate this approach will be suitable for the patterning of brushes, especially for biomedical applications such as in the study of single cells and of cell cocultures.

Enhancing neurite outgrowth from primary neurones and neural stem cells using thermoresponsive hydrogel scaffolds for the repair of spinal cord injury.

In this study, thermoresponsive xyloglucan hydrogel scaffolds were investigated as candidates for neural tissue engineering of the spinal cord. The hydrogels were optimized to provide similar mechanical properties to that of native spinal cord, although also being functionalized through the immobilization of poly-D-lysine to promote neurone adhesion and neurite outgrowth. Under 2D and 3D culture conditions, xyloglucan scaffolds supported the differentiation of primary cortical neurones. Furthermore, functionalization provided a means of controlling and optimizing the cell diameter, number, migration and the neurite density, and the direction of growth. The interaction of neural stem cells (NSCs) was also investigated on the xyloglucan scaffolds in vitro. The survival of the NSCs and the axonal extensions on the scaffolds were similar to that of the primary cortical neurones. These findings suggest that xyloglucan-based materials are suitable for providing a neurotrophic milieu.

Polylysine-functionalised thermoresponsive chitosan hydrogel for neural tissue engineering.

Foetal mouse cortical cells were cultured on 2D films and within 3D thermally responsive chitosan/glycerophosphate salt (GP) hydrogels. The biocompatibility of chitosan/GP 2D films was assessed in terms of cell number and neurites per cell. Osmolarity of the hydrogel was a critical factor in promoting cell survival with isotonic GP concentrations providing optimal conditions. To improve cell adhesion and neurite outgrowth, poly-D-lysine (PDL) was immobilised onto chitosan via azidoaniline photocoupling. Increase in PDL concentrations did not alter cell survival in 2D cultures but neurite outgrowth was significantly inhibited. Neurons exhibited a star-like morphology typical of 2D culture systems. The effects of PDL attachment on cell number, cell morphology and neurite outgrowth were more distinct in 3D culture conditions. Neurones exhibited larger cell bodies and sent out single neurites within the macroporous gel. Immobilised PDL improved cell survival up to an optimum concentration of 0.1%, however, further increases resulted in drops in cell number and neurite outgrowth. This was attributed to a higher cell interaction with PDL within a 3D hydrogel compared to the corresponding 2D surface. The results show that thermally responsive chitosan/GP hydrogels provide a suitable 3D scaffolding environment for neural tissue engineering.

Elimination of stick-slip of elastomeric sutures by radiofrequency glow discharge deposited coatings.

Fine elastomeric sutures intended for cardiovascular surgery can exhibit "stick-slip" behavior as they are pulled through tissue; the resulting oscillatory force can damage delicate tissue or cause sutures to snap. To eliminate this undesirable effect, sutures were surface-modified using a radiofrequency glow discharge in a vapor of either hexamethyldisiloxane or hexamethyldisilazane, to produce a thin polymeric coating on the suture. The same coatings were also deposited onto aluminized tape to facilitate their characterization by measurement of air/water contact angles and by X-ray photoelectron spectroscopy. Coatings from both monomers were found to be very hydrophobic. The hexamethyldisiloxane glow discharge coatings underwent negligible oxidation when stored in air, and thus remained stable over a shelf-life period akin to what may be required of sutures. The hexamethyldisilazane glow discharge coatings, in contrast, incorporated substantial amounts of oxygen over a 3-month period. The coatings did not measurably alter the tensile properties of the sutures. The frictional properties of coated sutures were assessed by measuring the dynamic friction between the suture and ovine myocardium. Both coatings were effective in removing the inherent stick-slip behavior of polybutester sutures in this model. The coatings remained intact after several passes and proved to be robust and efficacious under various strain regimes.

Polymer surface chemistry and bone cell migration.

Implant devices for orthopaedic applications may be improved if the surface of the biomaterial provides for osteointegration. To understand the effect of hydrophilicity on colonisation by human bone derived (HBD) cells, we compared untreated polystyrene (PS) and a sulfuric acid-treated PS surface for mechanisms of cell migration. The chemical composition of the acid-treated PS surface was analysed by monochromatic X-ray photoelectron spectroscopy and found to contain various oxidatively produced groups and a minor amount of sulfonate groups. It was found that migration of HBD cells on both PS and acid-treated PS surface was dependent on the presence of vitronectin (Vn) and was higher on the hydrophilic acid-treated surface. Minimal migration of HBD cells occurred on either surface in the absence of Vn, even when fibronectin was present in the culture medium. Using radiolabelled protein, it was shown that Vn adsorption onto the acid-treated surface was two to three fold greater than that on the hydrophobic PS. When HBD cells were seeded onto a patterned surface in a medium containing Vn, the cells preferentially colonised the hydrophilic region and few, if any, cells traversed the haptotactic boundary from the hydrophilic to the hydrophobic side. Thus the enhanced HBD cell migration seen on the acid-treated PS compared with the untreated PS surface and the haptotactic boundary phenomenon, relate to Vn adsorption.

A general method to recondition and reuse BIAcore sensor chips fouled with covalently immobilized protein/peptide.

Of significance in the routine use of BIAcore is the cost of the sensor chips. This is particularly evident during the phase of method development of an assay where it is not unusual to expend several chips in a day in attempts to optimize immobilization conditions for a novel peptide or protein. In addition, it is accepted practice to discard a chip once its ligand binding capacity has diminished to an unacceptable level. While the high cost of sensor chips has been addressed to some degree through the recent introduction of research-grade sensor chips, we were interested in assessing the possibility of regenerating or reconditioning sensor chips in order to allow them to be reused. In particular, we concerned ourselves with regenerating sensor chips onto which peptide or protein had been immobilized. Our aim was to develop a general procedure that would allow reuse of such chips but would not decrease ligand immobilization capacity or increase nonspecific ligand adsorption properties. We present a method which employs a combination of enzymatic (Pronase E) and chemical (bromoacetic acid) treatments of used sensor chips. Regeneration requires an overnight incubation of the sensor chip ex situ so that one can continue to perform BIAcore experiments. The data demonstrate that this simple two-step procedure substantially removes immobilized proteins such as IgG, Protein G, an HIV-1 envelope glycoprotein (gp 120) and a neoglycoprotein based on bovine serum albumin, as determined by reflectance measurements and X-ray photoelectron spectroscopy.(ABSTRACT TRUNCATED AT 250 WORDS)

Covalent attachment and non-specific binding of reactive probe molecules onto surfaces.

Optimization of strategies for the covalent attachment of proteins onto polymer surfaces requires the development of analytical methods which can differentiate between proteins that are covalently attached and those that are non-covalently bound (physisorbed). We probed for the surface density of reactive amine, carbonyl, and hydrazide groups using solution phase derivatization reactions to mimic and explore protein immobilization reaction strategies. Labeling compounds investigated were fluorescein derivatives, which were quantified by adsorption spectroscopy, and fluorinated phenyl compounds which were quantified by XPS. Control experiments consisted of performing the same labeling reactions using surfaces without reactive groups, or immersing the polymer surface into the labeling solution after blocking the reactive group of the labeling compound by a covalent reaction in solution. We always found non-negligible contributions arising from physisorption of the derivatization labels. Multiple control surfaces and a novel 'crossover derivatization-XPS' method were studied with the aim of improving compensation for physisorption. Our documentation of surprisingly large physisorption components even for small molecule labels, together with the known propensity of proteins to adsorb onto polymers, suggests caution in quantitative analysis of surface groups by derivatization, and in interpreting covalent protein immobilizations onto polymeric surfaces.

Roles of serum vitronectin and fibronectin in initial attachment of human vein endothelial cells and dermal fibroblasts on oxygen- and nitrogen-containing surfaces made by radiofrequency plasmas.

Fluoropolymers modified by plasma modification were studied for their suitability as surfaces for the adhesion of cells. We compared films made by plasma modification of fluoroethylenepropylene (FEP) using nitrogen-containing gases (ammonia or dimethyl acetamide) with films deposited using oxygen-containing monomers (methanol, methyl methacrylate or sequential treatment with toluene then water). The surfaces were compared for the attachment and spreading of human vein endothelial cells and human dermal fibroblasts. The initial attachment and spreading of cultured fibroblasts and endothelial cells onto films deposited using nitrogen-containing gases were equivalent to that onto films deposited using oxygen-containing monomers, but there were some differences in the mechanism of attachment. With films deposited using oxygen-containing monomers, the initial attachment and spreading of endothelial cells failed when the medium contained 15% (v/v) serum from which both fibronectin (Fn) and vitronectin (Vn) had been removed. Similarly, initial attachment and spreading of endothelial cells onto films deposited using oxygen-containing monomers were reduced by 62-86% when the cells were seeded in medium containing Vn-depleted serum (which contained Fn). Endothelial cells attached and spread onto films made using oxygen-containing monomers, when seeded in medium containing Fn-depleted serum (which contained Vn). On films deposited using nitrogen-containing gases, the adhesion of endothelial cells was only slightly reduced in Vn-depleted medium (as compared to attachment in medium containing unmodified serum). Furthermore, surfaces which had incorporated nitrogen were more effective than were oxygen-containing films in adsorbing sufficient serum Fn as to promote endothelial cell attachment. Similar results were seen for the attachment and spreading of fibroblasts as for the endothelial cells. For fibroblasts, attachment and spreading onto oxygen-containing films and onto nitrogen-containing films were not simply dependent upon either the Vn content or the Fn content of the medium. Maximal attachment and spreading of fibroblasts were, however, dependent upon adsorption of both serum Vn and Fn.

Growth of human cells on plasma polymers: putative role of amine and amide groups.

The attachment and growth of human endothelial cells and fibroblasts was studied on polymer surfaces fabricated by the polymerization of volatile amine and amide compounds in a low pressure gas plasma, and by the treatment of various surfaces in ammonia plasmas, which served to increase the nitrogen content of the surface layers. Infrared spectra showed the presence of amide groups, including those cases where the volatile compound ('monomer') did not contain oxygen. The performance of the surfaces in cell attachment correlated with the surface hydrophilicity and the nitrogen content, although for the latter a fair degree of scatter indicated that a more complex relationship applies. All these surfaces supported the attachment and growth of human cells. Generally, amide plasma polymers were best but the individual monomer and the plasma parameters also played a role. From comparisons of the various surfaces, it is suggested that the amide group is the main promoter of cell attachment in nitrogen-containing plasma surfaces.