Evaluation of alginate microspheres for mesenchymal stem cell engraftment on solid organ.

Mesenchymal stem cells (MSCs) may be used as a cell source for cell therapy of solid organs due to their differentiation potential and paracrine effect. Nevertheless, optimization of MSC-based therapy needs to develop alternative strategies to improve cell administration and efficiency. One option is the use of alginate microencapsulation, which presents an excellent biocompatibility and an in vivo stability. As MSCs are hypoimmunogenic, it was conceivable to produce microparticles with [alginate-poly-L-lysine-alginate (APA) microcapsules] or without (alginate microspheres) a surrounding protective membrane. Therefore, the aim of this study was to determine the most suitable microparticles to encapsulate MSCs for engraftment on solid organ. First, we compared the two types of microparticles with 4 × 10(6) MSCs/ml of alginate. Results showed that each microparticle has distinct morphology and mechanical resistance but both remained stable over time. However, as MSCs exhibited a better viability in microspheres than in microcapsules, the study was pursued with microspheres. We demonstrated that viable MSCs were still able to produce the paracrine factor bFGF and did not present any chondrogenic or osteogenic differentiation, processes sometimes reported with the use of polymers. We then proved that microspheres could be implanted under the renal capsule without degradation with time or inducing impairment of renal function. In conclusion, these microspheres behave as an implantable scaffold whose biological and functional properties could be adapted to fit with clinical applications.

Controlled release properties and final macroporosity of a pectin microspheres-calcium phosphate composite bone cement.

The use of calcium phosphate cements (CPC) is restricted by their lack of macroporosity and poor drug release properties. To overcome these two limitations, incorporating degradable polymer microparticles into CPC is an attractive option, as polymer microparticles could help to control drug release and induce macroporosity after degradation. Although few authors have yet tested synthetic polymers, the potentiality of polysaccharides' assuming this role has never been explored. Low-methoxy amidated pectins (LMAP) constitute valuable candidates because of their biocompatibility and ionic and pH sensitivity. In this study, the potentiality of a LMAP with a degree of esterification (DE) of 30 and a degree of amidation (DA) of 19 was explored. The aim of this study was to explore the influence of LMAP microspheres within the composite on the cement properties, drug release ability and final macroporosity after microspheres degradation. Three LMAP incorporation ratios, 2%, 4% and 6% w/w were tested, and ibuprofen was chosen as the model drug. In comparison with the CPC reference, the resulting composites presented reduced setting times and lowered the mechanical properties, which remained acceptable for an implantation in moderate-stress-bearing locations. Sustained release of ibuprofen was obtained on at least 45days, and release rates were found to be controlled by the LMAP ratio, which modulated drug diffusion. After 4months of degradation study, the resulting CPC appeared macroporous, with a maximum macroporosity of nearly 30% for the highest LMAP incorporation ratio, and interconnectivity between pores could be observed. In conclusion, LMAP appear as interesting candidates to generate macroporous bone cements with tailored release properties and macroporosity by adjusting the pectin content within the composites.

Rheological properties of calcium carbonate self-setting injectable paste.

With the development of minimally invasive surgical techniques, there is growing interest in the research and development of injectable biomaterials with controlled rheological properties. In this context, the rheological properties and injectability characteristics of an original CaCO(3) self-setting paste have been investigated. Two complementary rheometrical procedures have been established using a controlled stress rheometer to follow the structure build-up at rest or during gentle mixing and/or handling on the one hand, and the likely shear-induced breakdown of this structure at 25 or 35 degrees Celsius on the other. The data obtained clearly show the influence of temperature on the development of a cement microstructure during setting, in all cases leading to a microporous cement made of an entangled network of aragonite-CaCO(3) needle-like crystals. Linear viscoelastic measurements arriving from an oscillatory shear at low deformation showed a progressive increase in the viscous modulus (G'') during paste setting, which is enhanced by an increase in temperature. In addition, steady shear measurements revealed the shear-thinning behaviour of this self-setting paste over an extended period after paste preparation and its ability to re-build through progressive paste setting at rest. The shear-thinning behaviour of this self-setting system was confirmed using the injectability system and a procedure we designed. The force needed to extrude a homogeneous and continuous column of paste decreases strongly upon injection and reaches a weight level to apply on the syringe piston around 2.5 kg, revealing the ease of injection of this CaCO(3) self-setting paste.