ABSTRACT
This work explores the influence of a pre-engineered notch on the electromagnetic radiation (EMR) parameters in NiTi shape memory alloy (SMA) during tensile tests. The test data showed that the EMR signal fluctuated between oscillatory and exponential, signifying that the specimen's viscosity damping coefficient changes during strain hardening. The EMR parameters, maximum EMR amplitude, and average EMR energy release rate remained constant initially but rose sharply with the plastic zone radius with progressive loading. It was postulated that new Frank-Read sources permit dislocation multiplication and increase the number of edge dislocations participating in EMR emissions, leading to a rise in the value of EMR parameters. The study of the correlation between EMR emission parameters and the plastic zone radius before the crack tip is a vital crack growth monitoring tool. An analysis of the interrelationship of the EMR energy release rate at fracture with the elastic strain energy release rate would help develop an innovative approach to assess fracture toughness, a critical parameter for the design and safety of metals. The microstructural analysis of tensile fractures and the interrelation between deformation behaviours concerning the EMR parameters offers a novel and real-time approach to improve the extant understanding of the behaviour of metallic materials.
ABSTRACT
The widespread use of epoxy resin (ER) in industry, owing to its excellent properties, aligns with the global shift toward greener resources and energy-efficient solutions, where utilizing metal oxides in 3D printed polymer parts can offer extended functionalities across various industries. ZnO concentrations in polyurethane acrylate composites impacted adhesion and thickness of DLP samples, with 1 wt.% achieving a thickness of 3.99 ± 0.16 mm, closest to the target thickness of 4 mm, while 0.5 wt.% ZnO samples exhibited the lowest deviation in average thickness (±0.03 mm). Tensile stress in digital light processed (DLP) composites with ZnO remained consistent, ranging from 23.29 MPa (1 wt.%) to 25.93 MPa (0.5 wt.%), with an increase in ZnO concentration causing a reduction in tensile stress to 24.04 MPa and a decrease in the elastic modulus to 2001 MPa at 2 wt.% ZnO. The produced DLP samples, with their good corrosion resistance in alkaline environments, are well-suited for applications as protective coatings on tank walls. Customized DLP techniques can enable their effective use as structural or functional elements, such as in Portland cement concrete walls, floors and ceilings for enhanced durability and performance.
ABSTRACT
The present study focuses on the synthesis and characterisation of a lightweight ceramic material with electromagnetic interference (EMI) shielding properties, achieved using mullite containing micrometre-sized hollow spheres (cenospheres) and CoFe2O4 nanoparticles. This research explores compositions with varying CoFe2O4 contents ranging from 0 up to 20 wt.%. Conventional sintering in an air atmosphere is carried out at a temperature between 1100 and 1300 °C. The addition of ferrite nanoparticles was found to enhance the process of sintering cenospheres, resulting in improved material density and mechanical properties. Furthermore, this study reveals a direct correlation between the concentration of ferrite nanoparticles and the electromagnetic properties of the material. By increasing the concentration of ferrite nanoparticles, the electromagnetic shielding effect of the material (saturation magnetisation (Ms) and remanent magnetisation (Mr)) was observed to strengthen. These findings provide valuable insights into designing and developing lightweight ceramic materials with enhanced electromagnetic shielding capabilities. The synthesized ceramic material holds promise for various applications that require effective electromagnetic shielding, such as in the electronics, telecommunications, and aerospace industries.
ABSTRACT
Electrochemical Double Layer Capacitors (EDLCs) with ionic liquid electrolytes outperform conventional ones using aqueous and organic electrolytes in energy density and safety. However, understanding the electrochemical behaviors of ionic liquid electrolytes under compressive/tensile strain is essential for the design of flexible EDLCs as well as normal EDLCs, which are subject to external forces during assembly. Despite many experimental studies, the compression/stretching effects on the performance of ionic liquid EDLCs remain inconclusive and controversial. In addition, there is hardly any evidence of prior theoretical work done in this area, which makes the literature on this topic scarce. Herein, for the first time, we developed an atomistic model to study the processes underlying the electrochemical behaviors of ionic liquids in an EDLC under strain. Constant potential non-equilibrium molecular dynamics simulations are conducted for EMIM BF4 placed between two graphene walls as electrodes. Compared to zero strain, low compression of the EDLC resulted in compromised performance as the electrode charge density dropped by 29%, and the performance reduction deteriorated significantly with a further increase in compression. In contrast, stretching is found to enhance the performance by increasing the charge storage in the electrodes by 7%. The performance changes with compression and stretching are due to changes in the double-layer structure. In addition, an increase in the value of the applied potential during the application of strain leads to capacity retention with compression revealed by the newly performed simulations.
ABSTRACT
The need to use hydrogen (H2) gas has increasingly become important due to the growing demand for carbon-free energy sources. However, the explosive nature of H2 gas has raised significant safety concerns, driving the development of efficient and reliable detection. Although 2D materials have emerged as promising materials for hydrogen gas sensing applications due to their relatively high sensitivity, the incorporation of other nanomaterials into 2D materials can drastically improve both the selectivity and the sensitivity of sensors. In this work, high-entropy alloy nanoparticles using non-noble metals were used to develop a sensor for H2 gas detection. This chemical sensor was realized by decorating 2D MoS2 surfaces with multicomponent body-centered cubic (BCC) equiatomic Ti-Zr-V-Nb-Hf high-entropy alloy (HEA) nanoparticles. It was selective towards H2, over NH3, H2S, CH4, and C4H10, demonstrating widespread applications of this sensor. To understand the mechanisms behind the abnormal selectivity and sensitivity, density functional theory (DFT) calculations were performed, showing that the HEA nanoparticles can act as a chemical hub for H2 adsorption and dissociation, ultimately improving the performance of 2D material-based gas sensors.
ABSTRACT
We report the development of a coating system relying on the incorporation of SiO2@ZnO core-shell nanospheres in polyurethane media as a novel approach to achieve longevity and sustainability in marine transport. This polymeric coating showed significant improvement in surface abrasion resistance, the transition from a hydrophilic state to a hydrophobic state (~ 125.2° ± 2°), improved antifungal, antibacterial and antialgae effects which make the proposed coating ideal to protect steel surfaces against biofouling. To substantiate our claims, we performed X-ray diffraction, Transmission electron microscopy, Fourier transform infrared spectroscopy, scanning acoustic microscopy, Thermogravimetric analysis (TGA), contact angle measurements, antimicrobial (antialgal, antibacterial, antifungal) tests and Taber abrasion tests (ASTM D1044 and D4060) to highlight the mechanical and biological functionality as well as the bonding configuration of this coating. The wear analysis of the Taber abraded coating using SEM and optical microscopy showed significant improvement in the adhesion and shear resistance achieved by the SiO2@ZnO core-shell nanospheres incorporated PU coating which was a contrasting feature compared to using PU alone. The overall investigations we performed led us to find out that the addition of 4% (wt.) SiO2@ZnO core-shell nanoparticles to the PU media deposited on the low carbon steel surface demonstrated remarkable antimicrobial performance with almost no bacterial growth, significant reductions in growth for algae to about 90% and fungus to about 95%.
ABSTRACT
In this brief review, we discuss the recent advancements in using poly(ethylene glycol) diacrylate (PEGDA) hydrogels for tissue engineering applications. PEGDA hydrogels are highly attractive in biomedical and biotechnology fields due to their soft and hydrated properties that can replicate living tissues. These hydrogels can be manipulated using light, heat, and cross-linkers to achieve desirable functionalities. Unlike previous reviews that focused solely on material design and fabrication of bioactive hydrogels and their cell viability and interactions with the extracellular matrix (ECM), we compare the traditional bulk photo-crosslinking method with the latest three-dimensional (3D) printing of PEGDA hydrogels. We present detailed evidence combining the physical, chemical, bulk, and localized mechanical characteristics, including their composition, fabrication methods, experimental conditions, and reported mechanical properties of bulk and 3D printed PEGDA hydrogels. Furthermore, we highlight the current state of biomedical applications of 3D PEGDA hydrogels in tissue engineering and organ-on-chip devices over the last 20 years. Finally, we delve into the current obstacles and future possibilities in the field of engineering 3D layer-by-layer (LbL) PEGDA hydrogels for tissue engineering and organ-on-chip devices.
ABSTRACT
Three-dimensional (3D) printed hydrogels fabricated using light processing techniques are poised to replace conventional processing methods used in tissue engineering and organ-on-chip devices. An intrinsic potential problem remains related to structural heterogeneity translated in the degree of cross-linking of the printed layers. Poly(ethylene glycol) diacrylate (PEGDA) hydrogels were used to fabricate both 3D printed multilayer and control monolithic samples, which were then analyzed using atomic force microscopy (AFM) to assess their nanomechanical properties. The fabrication of the hydrogel samples involved layer-by-layer (LbL) projection lithography and bulk cross-linking processes. We evaluated the nanomechanical properties of both hydrogel types in a hydrated environment using the elastic modulus (E) as a measure to gain insight into their mechanical properties. We observed that E increases by 4-fold from 2.8 to 11.9 kPa transitioning from bottom to the top of a single printed layer in a multilayer sample. Such variations could not be seen in control monolithic sample. The variation within the printed layers is ascribed to heterogeneities caused by the photo-cross-linking process. This behavior was rationalized by spatial variation of the polymer cross-link density related to variations of light absorption within the layers attributed to spatial decay of light intensity during the photo-cross-linking process. More importantly, we observed a significant 44% increase in E, from 9.1 to 13.1 kPa, as the indentation advanced from the bottom to the top of the multilayer sample. This finding implies that mechanical heterogeneity is present throughout the entire structure, rather than being limited to each layer individually. These findings are critical for design, fabrication, and application engineers intending to use 3D printed multilayer PEGDA hydrogels for in vitro tissue engineering and organ-on-chip devices.
ABSTRACT
Nearly ~ 108 types of High entropy alloys (HEAs) can be developed from about 64 elements in the periodic table. A major challenge for materials scientists and metallurgists at this stage is to predict their crystal structure and, therefore, their mechanical properties to reduce experimental efforts, which are energy and time intensive. Through this paper, we show that it is possible to use machine learning (ML) in this arena for phase prediction to develop novel HEAs. We tested five robust algorithms namely, K-nearest neighbours (KNN), support vector machine (SVM), decision tree classifier (DTC), random forest classifier (RFC) and XGBoost (XGB) in their vanilla form (base models) on a large dataset screened specifically from experimental data concerning HEA fabrication using melting and casting manufacturing methods. This was necessary to avoid the discrepancy inherent with comparing HEAs obtained from different synthesis routes as it causes spurious effects while treating an imbalanced data-an erroneous practice we observed in the reported literature. We found that (i) RFC model predictions were more reliable in contrast to other models and (ii) the synthetic data augmentation is not a neat practice in materials science specially to develop HEAs, where it cannot assure phase information reliably. To substantiate our claim, we compared the vanilla RFC (V-RFC) model for original data (1200 datasets) with SMOTE-Tomek links augmented RFC (ST-RFC) model for the new datasets (1200 original + 192 generated = 1392 datasets). We found that although the ST-RFC model showed a higher average test accuracy of 92%, no significant breakthroughs were observed, when testing the number of correct and incorrect predictions using confusion matrix and ROC-AUC scores for individual phases. Based on our RFC model, we report the development of a new HEA (Ni25Cu18.75Fe25Co25Al6.25) exhibiting an FCC phase proving the robustness of our predictions.
ABSTRACT
Hydrogels are commonly used materials in tissue engineering and organ-on-chip devices. This study investigated the nanomechanical properties of monolithic and multilayered poly(ethylene glycol) diacrylate (PEGDA) hydrogels manufactured using bulk polymerization and layer-by-layer projection lithography processes, respectively. An increase in the number of layers (or reduction in layer thickness) from 1 to 8 and further to 60 results in a reduction in the elastic modulus from 5.53 to 1.69 and further to 0.67 MPa, respectively. It was found that a decrease in the number of layers induces a lower creep index (CIT) in three-dimensional (3D) printed PEGDA hydrogels. This reduction is attributed to mesoscale imperfections that appear as pockets of voids at the interfaces of the multilayered hydrogels attributed to localized regions of unreacted prepolymers, resulting in variations in defect density in the samples examined. An increase in the degree of cross-linking introduced by a higher dosage of ultraviolet (UV) exposure leads to a higher elastic modulus. This implies that the elastic modulus and creep behavior of hydrogels are governed and influenced by the degree of cross-linking and defect density of the layers and interfaces. These findings can guide an optimal manufacturing pathway to obtain the desirable nanomechanical properties in 3D printed PEGDA hydrogels, critical for the performance of living cells and tissues, which can be engineered through control of the fabrication parameters.
ABSTRACT
Every sixth person in the world dies due to cancer, making it the second leading severe cause of death after cardiovascular diseases. According to WHO, cancer claimed nearly 10 million deaths in 2020. The most common types of cancers reported have been breast (lung, colon and rectum, prostate cases), skin (non-melanoma) and stomach. In addition to surgery, the most widely used traditional types of anti-cancer treatment are radio- and chemotherapy. However, these do not distinguish between normal and malignant cells. Additional treatment methods have evolved over time for early detection and targeted therapy of cancer. However, each method has its limitations and the associated treatment costs are quite high with adverse effects on the quality of life of patients. Use of individual atoms or a cluster of atoms (nanoparticles) can cause a paradigm shift by virtue of providing point of sight sensing and diagnosis of cancer. Nanoparticles (1-100 nm in size) are 1000 times smaller in size than the human cell and endowed with safer relocation capability to attack mechanically and chemically at a precise location which is one avenue that can be used to destroy cancer cells precisely. This review summarises the extant understanding and the work done in this area to pave the way for physicians to accelerate the use of hybrid mode of treatments by leveraging the use of various nanoparticles.
Subject(s)
Cardiovascular Diseases , Melanoma , Nanoparticles , Male , Humans , Quality of LifeABSTRACT
Many new engineering and scientific innovations have been proposed to date to passivate the novel coronavirus (SARS CoV-2), with the aim of curing the related disease that is now recognised as COVID-19. Currently, vaccine development remains the most reliable solution available. Efforts to provide solutions as alternatives to vaccinations are growing and include established control of behaviours such as self-isolation, social distancing, employing facial masks and use of antimicrobial surfaces. The work here proposes a novel engineering method employing the concept of resonant frequencies to denature SARS CoV-2. Specifically, "modal analysis" is used to computationally analyse the Eigenvalues and Eigenvectors i.e. frequencies and mode shapes to denature COVID-19. An average virion dimension of 63 nm with spike proteins number 6, 7 and 8 were examined, which revealed a natural frequency of a single virus in the range of 88-125 MHz. The information derived about the natural frequency of the virus through this study will open newer ways to exploit medical solutions to combat future pandemics.
Subject(s)
COVID-19 , SARS-CoV-2 , Finite Element Analysis , Humans , Pandemics/prevention & control , Spike Glycoprotein, Coronavirus/metabolismABSTRACT
The use of computational fluid dynamics (CFD) to simulate the spread of COVID19 and many other airborne diseases, especially in an indoor environment needs accurate understanding of dispersion models. Modelling the transport/dispersion of vapour droplets within the atmosphere is a complex problem, as it involves the motion of more than one phase, as well as the interphase interactions between the phases. This paper reviews the current canon of research on dispersion modelling of vapour droplets by looking at three specific aspects: (i) physical definition/specification of the initial droplet size distribution; (ii) physics of evaporation/condensation models and (iii) transport equations (with molecular/turbulent dispersion models) to describe the movement of the vapour droplets as they propagate through the air. This review found that the state of modelling implements a wide range of models which shows variances in results thus leading to a state where it is difficult to know which model is most accurate. The authors suggest that further studies in this direction should focus on developing a principle set of equations by benchmarking the previously developed models to establish model uncertainty of the previously developed models with reference to a fixed theoretical model and be compared under identical conditions. However, it must be noted that due to the complex nature of microdroplet evaporation and dispersion coupled with the unpredictable way droplet size distributions are produced, current experimental methodologies that are available to validate such simulations, such as particle image velocimetry, are still not robust enough to provide detailed data to verify minute aspects of the simulations.
ABSTRACT
Contribution of finite element method (FEM) as a modelling and simulation technique to represent complex tribological processes has improved our understanding about various biomaterials. This paper presents a review of the advances in the domain of finite element (FE) modelling for simulating tribology, wear, cutting and other processes involving high-strain rate plastic deformation of metals used in bio tribology and machining. Although the study is largely focused on material removal cases in metals, the modelling strategies can be applied to a wide range of other materials. This study discusses the development of friction models, meshing and remeshing strategies, and constitutive material models. The mesh-based and meshless formulations employed for bio tribological simulations with their advantages and limitations are also discussed. The output solution variables including scratch forces, local temperature, residual stresses are analyzed as a function of input variables.
Subject(s)
Metals , Plastics , Biocompatible Materials , Friction , Prostheses and ImplantsABSTRACT
Industry 4.0 in healthcare involves use of a wide range of modern technologies including digitisation, artificial intelligence, user response data (ergonomics), human psychology, the Internet of Things, machine learning, big data mining, and augmented reality to name a few. The healthcare industry is undergoing a paradigm shift thanks to Industry 4.0, which provides better user comfort through proactive intervention in early detection and treatment of various diseases. The sector is now ready to make its next move towards Industry 5.0, but certain aspects that motivated this review paper need further consideration. As a fruitful outcome of this review, we surveyed modern trends in this arena of research and summarised the intricacies of new features to guide and prepare the sector for an Industry 5.0-ready healthcare system.
ABSTRACT
The transition metal carbides/nitrides referred to as MXenes has emerged as a wonder material presenting newer opportunities owing to their unique properties such as high thermal and electrical conductivity, high negative zeta-potential and mechanical properties similar to the parent transition metal carbides/nitrides. These properties of MXenes can be utilized in various societal applications including for energy storage and energy conversion. In this focused review, we provide a ready glance into the evolutionary development of the MXene family and various efforts that are made globally towards property improvement and performance enhancement. Particular attention in this review is made to direct the attention of readers to the bright prospects of MXene in the energy storage and energy conversion process - which is extremely timely to tackle the current concern on climate change. The review concludes by offering fresh insights into the future research needs and challenges that need to be addressed to develop resilient energy solutions.
ABSTRACT
High-throughput and high-accuracy nanofabrication methods are required for the ever-increasing demand for nanoelectronics, high-density data storage devices, nanophotonics, quantum computing, molecular circuitry, and scaffolds in bioengineering used for cell proliferation applications. The scanning probe lithography (SPL) nanofabrication technique is a critical nanofabrication method with great potential to evolve into a disruptive atomic-scale fabrication technology to meet these demands. Through this timely review, we aspire to provide an overview of the SPL fabrication mechanism and the state-the-art research in this area, and detail the applications and characteristics of this technique, including the effects of thermal aspects and chemical aspects, and the influence of electric and magnetic fields in governing the mechanics of the functionalized tip interacting with the substrate during SPL. Alongside this, the review also sheds light on comparing various fabrication capabilities, throughput, and attainable resolution. Finally, the paper alludes to the fact that a majority of the reported literature suggests that SPL has yet to achieve its full commercial potential and is currently largely a laboratory-based nanofabrication technique used for prototyping of nanostructures and nanodevices.
ABSTRACT
The stepwise hydration of clay minerals has been observed repeatedly in studies, but the underlying mechanism remains unclear. Previous numerical studies confirmed the presence of one-water layer (1W) and two-water layer (2W) hydration states. However, the undisturbed transition between these hydration states has never been captured. Using molecular dynamics simulation, this study (i) simulated for the first time the free 1W-2W transition during clay hydration and (ii) identified the underlying mechanism to be the detachment of cations from the clay surface and the formation of a shell of water molecules around the cation. The swelling dynamics of clay was found to be affected by the clay charge, clay mineralogy, and counterions through complex cation-clay interactions, cation hydration capacity, and cation migration rate.
ABSTRACT
Fermentation of cocoa is a key process to obtain aromatic chocolate products from raw cocoa beans. Hitherto, the levels of fermentation in cocoa are determined using destructive techniques, for example by a cut-test to manually observe the colour inside the beans, or by quantifying ammonia nitrogen (NH3) in the cocoa powder. In this paper, we present the use of Terahertz hyperspectral imaging as a new way to non-destructively analyse and detect fermented cocoa beans. The study analysed two sets of twenty-two cocoa bean samples with different levels of fermentation from two producers in Brazil. A correlation between fermentation conditions and the outcome results of their THz measurements was observed.