ABSTRACT
We report the numerical and experimental study of probe pulse deformation in a forward-pumped distributed Raman amplifier on a 40-km standard single mode fiber. Distributed Raman amplification can improve the range of OTDR-based sensing systems, but it could result in pulse deformation. A smaller Raman gain coefficient can be used to mitigate pulse deformation. The sensing performance can still be maintained by compensating for the decrease in the Raman gain coefficient by increasing the pump power. The tunability of the Raman gain coefficient and pump power levels are predicted while keeping the probe power below the modulation instability limit.
ABSTRACT
We demonstrate the use of the electrooptic effect to control the propagation constant of the guided modes in silicate few mode fibers with internal electrodes. The electrooptic effect induces a perturbation of the fiber's refractive index profile that controls intermodal interference. To increase the electrooptic effect the silicate fibers are poled. The response time is in the nanosecond range.
ABSTRACT
Higher-order mode converters that work over a broad wavelength range are needed for various applications. A new, to the best of our knowledge, simple and cost-effective LP02 mode converter is fabricated by tapering a bundle of single-mode fibers. The device excites the LP02 mode in a four-mode step index fiber with a mode purity higher than 10 dB. The polarization-dependent cross talk of the device is measured using the S2 technique. The LP02 mode selectivity of the device is measured over the entire C and L bands by selectively launching different modes into the device using a spatial light modulator.
ABSTRACT
We present the first demonstration of shot-noise limited supercontinuum-based spectral domain optical coherence tomography (SD-OCT) with an axial resolution of 5.9 µm at a center wavelength of 1370 nm. Current supercontinuum-based SD-OCT systems cannot be operated in the shot-noise limited detection regime because of severe pulse-to-pulse relative intensity noise of the supercontinuum source. To overcome this disadvantage, we have developed a low-noise supercontinuum source based on an all-normal dispersion (ANDi) fiber, pumped by a femtosecond laser. The noise performance of our 90 MHz ANDi fiber-based supercontinuum source is compared to that of two commercial sources operating at 80 and 320 MHz repetition rate. We show that the low-noise of the ANDi fiber-based supercontinuum source improves the OCT images significantly in terms of both higher contrast, better sensitivity, and improved penetration. From SD-OCT imaging of skin, retina, and multilayer stacks we conclude that supercontinuum-based SD-OCT can enter the domain of shot-noise limited detection.
ABSTRACT
Methods for measurement of polarization dependent loss and cross talk of individual few mode fiber components and connected systems are presented. A new method for determining the cross talk of the individual components, from the measurements on the connected system is presented and verified through simulations and measurements. The method is based on Fourier analysis of the wavelength dependent interference of the loss of the system.
ABSTRACT
We present a robust fiber-based setup for Bessel-like beam extended depth-of-focus Fourier-domain optical coherence microscopy, where the Bessel-like beam is generated in a higher order mode fiber module. In this module a stable guided LP02 core mode is selectively excited by a long period grating written in the higher order mode fiber. Imaging performance of this system in terms of lateral resolution and depth of focus was analyzed using samples of suspended microbeads and compared to the case where illumination is provided by the fundamental LP01 mode of a single mode fiber. Illumination with the LP02 mode allowed for a lateral resolution down to 2.5 µm as compared to 4.5 µm achieved with the LP01 mode of the single mode fiber. A three-fold enhancement of the depth of focus compared to a Gaussian beam with equally tight focus is achieved with the LP02 mode. Analysis of the theoretical lateral point spread functions for the case of LP01 and LP02 illumination agrees well with the experimental data. As the design space of waveguides and long-period gratings allows for further optimization of the beam parameters of the generated Bessel-like beams in an all-fiber module, this approach offers a robust and yet flexible alternative to free-space optics approaches or the use of conical fiber tips.
ABSTRACT
We have fabricated an air-cladded mode-group selective photonic lantern, which can (de)multiplex the first two mode groups of a standard two-mode step-index fiber. Instead of relying on a low-index capillary tube, our simple solution uses air to form the surrounding "cladding" and thereby enable guiding at the end of the taper. Characterization of a 25-mm long lantern taper results in multiplexing crosstalk values between -20 dB and -12 dB for both modal inputs. The de-multiplexing values were around -12 dB for the fundamental mode, and slightly higher for the first higher-order (LP11) mode. Microscopic imaging of a taper cross section having a width of 30 µm reveals the presence of an uncollapsed airhole in the structure between the three fibers. The impact of such an airhole is numerically investigated using an eigenmode expansion method based on a full-vectorial mode solver, and is found to play an important role in assuring a more adiabatic mode conversion through the taper.
ABSTRACT
The increasing use of few-mode fibers for high-speed optical communication systems in space division multiplexing has created a need for mode resolved characterization of few-mode fibers. In this Letter, we present a new method to characterize the bend loss of the individual modes in a few-mode fiber. This procedure uses a simple setup for spatially and spectrally resolved imaging and allows the measurement of the bend loss of each and every guided mode at once. It does not require the use of mode converters in contrast to other methods. Results for graded-index two- and four-mode fibers are presented, together with comparisons against direct bend-loss measurements for the four-mode and standard single-mode fibers.
ABSTRACT
A new method for direct writing of localized, circularly symmetric refractive-index changes in optical fibers with a femtosecond laser is demonstrated. The refractive-index changes are characterized using a novel approach employing comparison of numerical simulations to the measured far-field profiles of unmodified and modified fibers. From the analysis, a negative refractive-index change of -0.015±0.005 within a radius of (0.6±0.1) µm is determined.
ABSTRACT
Variable optical attenuation (VOA) for three-mode fiber is experimentally presented, utilizing an amplitude spatial light modulator (SLM), achieving up to -28dB uniform attenuation for all modes. Using the ability to spatially vary the attenuation distribution with the SLM, we also achieve up to 10dB differential attenuation between the fiber's two supported mode group (LP01 and LP11). The spatially selective attenuation serves as the basis of a dynamic mode-group equalizer (DME), potentially gain-balancing mode dependent optical amplification. We extend the experimental three mode DME functionality with a performance analysis of a fiber supporting 6 spatial modes in four mode groups. The spatial modes' distribution and overlap limit the available dynamic range and performance of the DME in the higher mode count case.
ABSTRACT
Long-term stable, sub-femtosecond timing distribution over a 1.2-km polarization-maintaining (PM) fiber-optic link using balanced optical cross-correlators for link stabilization is demonstrated. Novel dispersion-compensating PM fiber was developed to construct a dispersion-slope-compensated PM link, which eliminated slow timing drifts and jumps previously induced by polarization mode dispersion in standard single-mode fiber. Numerical simulations of nonlinear pulse propagation in the fiber link confirmed potential sub-100-as timing stability for pulse energies below 70 pJ. Link operation for 16 days showed ~0.6 fs RMS timing drift and during a 3-day interval only ~0.13 fs drift, which corresponds to a stability level of 10(-21).
ABSTRACT
We demonstrate a high-efficiency intermodal four-wave-mixing process in an all-fiber system, comprising a picosecond fiber laser and a high-order-mode (HOM) fiber. Two pump photons in the LP(01) mode of the fiber can generate an anti-Stokes photon in the LP(01) mode and a Stokes photon in the LP(02) mode. The wavelength dependent mode profiles of the HOM fiber produce significant spatial overlap between the modes involved. The anti-Stokes wave at 941 nm is generated with 20% conversion efficiency with input pulse energy of 20 nJ. The guidance of the anti-Stokes and Stokes waves in the HOM fiber enhances system stability.
ABSTRACT
We demonstrate an intermodal Cerenkov radiation effect in a higher-order-mode (HOM) fiber with a mode crossing (i.e., two guided modes having the same propagation constant at the same wavelength). A frequency-shifted soliton in the vicinity of the mode-crossing wavelength emits a phase-matched dispersive wave in a different propagation mode. We develop a theoretical explanation for this nonlinear optical effect and demonstrate that the mode crossing in HOM fibers can be utilized to achieve simultaneous wavelength and mode conversion; the strength of this intermodal nonlinear interaction can be tuned by controlled fiber bending.
Subject(s)
Optical Fibers , Optical Phenomena , Nonlinear Dynamics , Silicon Dioxide , Spectrum AnalysisABSTRACT
Conventional highly-nonlinear fiber (HNLF) designs are optimized for high field-confinement but are also inherently susceptible to dispersion fluctuations. The design compromise prevents fiber-optical parametric mixers from possessing high power efficiency and extended operating bandwidth simultaneously. Using a new fiber waveguide design, we have fabricated and tested a new class of HNLF that possesses a significantly lower level of dispersion fluctuations while maintaining a high level of field-confinement comparable to that in conventional HNLFs. The fiber was used to demonstrate an all-fiber parametric oscillator operating in short-wavelength infrared (SWIR) band with a watt-level pump, for the first time.
Subject(s)
Fiber Optic Technology/instrumentation , Telecommunications/instrumentation , Computer-Aided Design , Equipment Design , Equipment Failure Analysis , Nonlinear DynamicsABSTRACT
A method for measuring the effective refractive-index differences in a few-mode fiber by applying axial fiber stretching is described. This method represents a straightforward technique for characterization of few-mode fibers. Interference between LP01 and LP11 and in some cases also between LP11 and LP21 are observed in a fiber designed for support of LP01 and LP11. The relative strength of the coupled modes depends on specific splicing characteristics, and in some cases only two modes are seen. The results agree well with theoretical predictions for the fiber under investigation.
Subject(s)
Equipment Failure Analysis/instrumentation , Equipment Failure Analysis/methods , Optical Fibers , Refractometry/instrumentation , Refractometry/methods , Computer-Aided Design , Stress, MechanicalABSTRACT
We present a new multimode dispersion measurement technique based on the time-of-flight method. The modal delay and group velocity dispersion of all excited modes in a few-mode fiber can be measured simultaneously by a tunable pulsed laser and a high speed sampling oscilloscope. A newly designed higher-order-mode fiber with large anomalous dispersion in the LP(02) mode has been characterized using this method, and experimental results are in good agreement with the designed dispersion values. The demonstrated technique is significantly simpler to implement than the existing frequency-domain or interferometry-based methods.
Subject(s)
Optical Fibers , Optical Phenomena , Lasers , Silicon Dioxide , Time FactorsABSTRACT
We describe the design optimization of a higher-order-mode (HOM) fiber for energetic soliton propagation at wavelengths below 1300 nm. A new HOM fiber is fabricated according to our design criteria. The HOM fiber is pumped at 1045 nm by an energetic femtosecond fiber laser. The soliton self-frequency shift process shifts the center wavelength of the soliton to 1085 nm. The soliton has a temporal duration of 216 fs and a pulse energy of 6.3 nJ. The demonstrated pulse energy is approximately six times higher than the previous record in a solid core fiber at wavelengths below 1300 nm.
Subject(s)
Optical Fibers , Refractometry/instrumentation , Computer-Aided Design , Equipment Design , Equipment Failure Analysis , Light , Scattering, RadiationABSTRACT
We demonstrate generation of Cerenkov radiation at 850 nm in a higher-order-mode (HOM) fiber. The LP02 mode in this solid, silica-based fiber has anomalous dispersion from 690 nm to 810 nm. Cerenkov radiation with 3 nJ pulse energy is generated in this module, exhibiting 60% energy conversion efficiency from the input. The HOM fiber provides a valuable fiber platform for nonlinear wavelength conversion with pulse energies in-between index-guided silica-core photonic crystal fibers and air-core photonic bandgap fibers.
Subject(s)
Optical Fibers , Equipment Design , Equipment Failure Analysis , Light , Scattering, RadiationABSTRACT
A "black-box" phase sensitive amplifier is presented achieving simultaneous suppression of deterministic phase distortion on two independent 42.66 Gbit/s DPSK modulated signal wavelengths.
ABSTRACT
We report the first higher-order-mode fiber with anomalous dispersion at 800nm and demonstrate its potential in femtosecond pulse delivery for Ti:Sapphire femtosecond lasers. We obtain 125fs pulses after propagating a distance of 3.6 meters in solid-silica fiber. The pulses could be further compressed in a quartz rod to nearly chirp-free 110fs pulses. Femtosecond pulse delivery is achieved by launching the laser output directly into the delivery fiber without any pre-chirping of the input pulse. The demonstrated pulse delivery scheme suggests scaling to >20meters for pulse delivery in harsh environments not suited for oscillator operation or in applications that require long distance flexibility.