Attachment of endothelial colony-forming cells onto a surface bearing immobilized anti-CD34 antibodies: Specific CD34 binding versus nonspecific binding.

Cardiovascular disease is a leading cause of death worldwide; however, despite substantial advances in medical device surface modifications, no synthetic coatings have so far matched the native endothelium as the optimal hemocompatible surface for blood-contacting implants. A promising strategy for rapid restoration of the endothelium on blood-contacting biomedical devices entails attracting circulating endothelial cells or their progenitors, via immobilized cell-capture molecules; for example, anti-CD34 antibody to attract CD34+ endothelial colony-forming cells (ECFCs). Inherent is the assumption that the cells attracted to the biomaterial surface are bound exclusively via a specific CD34 binding. However, serum proteins might adsorb in-between or on the top of antibody molecules and attract ECFCs via other binding mechanisms. Here, we studied whether a surface with immobilized anti-CD34 antibodies attracts ECFCs via a specific CD34 binding or a nonspecific (non-CD34) binding. To minimize serum protein adsorption, a fouling-resistant layer of hyperbranched polyglycerol (HPG) was used as a "blank slate," onto which anti-CD34 antibodies were immobilized via aldehyde-amine coupling reaction after oxidation of terminal diols to aldehydes. An isotype antibody, mIgG1, was surface-immobilized analogously and was used as the control for antigen-binding specificity. Cell binding was also measured on the HPG hydrogel layer before and after oxidation. The surface analysis methods, x-ray photoelectron spectroscopy and time-of-flight secondary ion mass spectrometry, were used to verify the intended surface chemistries and revealed that the surface coverage of antibodies was sparse, yet the anti-CD34 antibody grafted surface-bound ECFCs very effectively. Moreover, it still captured the ECFCs after BSA passivation. However, cells also attached to oxidized HPG and immobilized mIgG1, though in much lower amounts. While our results confirm the effectiveness of attracting ECFCs via surface-bound anti-CD34 antibodies, our observation of a nonspecific binding component highlights the importance of considering its consequences in future studies.

Candida auris susceptibility on surfaces coated with the antifungal drug caspofungin.

Candida auris is known to survive for weeks on solid material surfaces. Its longevity contributes to medical device contamination and spread through healthcare facilities. We fabricated antifungal surface coatings by coating plastic and glass surfaces with a thin polymer layer to which the antifungal drug caspofungin was covalently conjugated. Caspofungin-susceptible and -resistant C. auris strains were inhibited on these surfaces by 98.7 and 81.1%, respectively. Cell viability studies showed that this inhibition was fungicidal. Our findings indicate that C. auris strains can be killed on contact when exposed to caspofungin that is reformulated as a covalently-bound surface layer. LAY SUMMARY: Candida auris is pathogenic, multidrug resistant yeast with the ability to survive on surfaces and remain transmissible for long periods of time in healthcare settings. In this study, we have prepared an antifungal surface coating and demonstrated its ability to kill adhering C. auris cells on contact.

Assessment of nonreleasing antifungal surface coatings bearing covalently attached pharmaceuticals.

There are many reports of antimicrobial coatings bearing immobilized active agents on surfaces; however, strong analytical evidence is required to verify that the agents are indeed covalently attached to the surface. In the absence of such evidence, antimicrobial activity could result from a release of active agents. We report a detailed assessment of antifungal surface coatings prepared using covalent attachment chemistries, with the aim of establishing a set of instrumental and biological evidence required to convincingly demonstrate antimicrobial activity due to nonreleasing, surface active compounds and to exclude the alternate possibility of activity due to release. The strongest biological evidence initially supporting permanent antifungal activity was the demonstration of the ability to reuse samples in multiple, sequential pathogen challenges. However, additional supporting evidence from washing studies and instrumental analysis is also required to probe the possibility of gradual desorption of strongly physisorbed compounds versus covalently attached compounds. Potent antifungal surface coatings were prepared from approved pharmaceutical compounds from the echinocandin drug class (caspofungin, anidulafungin, and micafungin) and assessed by microbiological tests and instrumental methods. Carbonyl diimidazole linking chemistry enabled covalent attachment of caspofungin, anidulafungin, and micafungin to plasma polymer surfaces, with antifungal surface activity likely caused by molecular orientations that present the lipophilic tail toward interfacing fungal cells. This study demonstrates the instrumental and biological evidence required to convincingly ascertain activity due to nonreleasing, surface active compounds and summarize these as three criteria for assessing other reports on surface-immobilized antimicrobial compounds.

Candida albicans Can Survive Antifungal Surface Coatings on Surfaces with Microcone Topography.

This study demonstrates the ability of Candida albicans, a medically significant human fungal pathogen, to minimize contact with an antifungal surface coating that on a flat surface is lethal on contact by growing on and between micron-sized surface topographical features, thus minimizing the contact area. Scanning electron microscopy showed that cells contacting the "floor" between microcones were killed, whereas cells attached to microcones survived and formed hyphal filaments. These spanned space between cones and avoided contact with the flat surface in-between cones. Thus, fungal cells managed to attach and grow despite the antifungal coating. This ability of Candida albicans to exploit topography features to minimize surface contact yet utilize the solid surface for anchoring reduces the effectiveness of the grafted antifungal surface coating. This suggests that biomedical devices with rough surfaces might be more challenging to protect against fungal biofilm formation via application of an antifungal coating.

Combatting fungal biofilm formation by diffusive release of fluconazole from heptylamine plasma polymer coating.

A drug-eluting coating applied onto biomedical devices and implants is an appropriate way to ensure that an inhibitory concentration of antimicrobial drugs is present at the device surface, thus preventing surface colonization and subsequent biofilm formation. In this study, a thin polymer coating was applied to materials, and it acted as a drug-delivery reservoir capable of surface delivery of the antifungal drug fluconazole to amounts up to 21 µg/cm2. The release kinetics into aqueous solution were quantified by UV spectroscopy and conformed to the Ritger-Peppas and Korsmeyer-Peppas model. Complementary microbiological assays were used to determine effectiveness against Candida albicans attachment and biofilm formation, and against the control heptylamine plasma polymer coating without drug loading, on which substantial fungal growth occurred. Fluconazole release led to marked antifungal activity in all assays, with log 1.6 reduction in CFUs/cm2. Cell viability assays and microscopy revealed that fungal cells attached to the fluconazole-loaded coating remained rounded and did not form hyphae and biofilm. Thus, in vitro screening results for fluconazole-releasing surface coatings showed efficacy in the prevention of the formation of Candida albicans biofilm.

Modulation of substrate van der Waals forces using varying thicknesses of polymer overlayers.

Thin polymeric coatings are commonly used for altering surface properties and modulating the interfacial performance of materials. Possible contributions from the substrate to the interfacial forces and effects are, however, usually ignored and are not well understood, nor is it established how the coating thickness modulates and eventually eliminates contributions from substrates to the van der Waals (vdW) interfacial force. In this study we quantified, by colloid-probe atomic force microscope (AFM) and by theoretical calculations, the interfacial vdW contributions from substrates acting through ethanol plasma polymer (EtOHpp) coatings of a range of thicknesses on Au and Si bulk materials. In approach force curves against EtOHpp-coated Au substrates the magnitude of the vdW force decreased as the EtOHpp coating thickness increased to 18 nm and then plateaued with further increases in coating thickness, providing direct evidence for a contribution to the total interfacial vdW force from the Au substrate acting through thin coatings. The experimental observations accord with theoretical calculations of the thickness dependence of Hamaker coefficients derived from rigorous simulation using the Lifshitz theory. In addition, the measured forces agree well with theoretical predictions including correction for finite roughness. Thus, our experimental and theoretical results establish how the thickness of polymer thin film coatings modulates the total interfacial vdW force and how this can be used to tune the net vdW force so as to either contain a large substrate contribution or arise predominantly from the polymeric overlayer. Our findings enable rational design of coating thickness to tailor interfacial interactions and material performance.

Bacterial membrane permeability of antimicrobial polymethacrylates: Evidence for a complex mechanism from super-resolution fluorescence imaging.

Amphiphilic polymers bearing cationic moieties are an emerging alternative to traditional antibiotics given their broad-spectrum activity and low susceptibility to the development of resistance. To date, however, much remains unclear regarding their mechanism of action. Using functional assays (ATP leakage, cell viability, DNA binding) and super-high resolution structured illumination microscopy (OMX-SR) of fluorescently tagged polymers, we present evidence for a complex mechanism, involving membrane permeation as well as cellular uptake, interaction with intracellular targets and possible complexation with bacterial DNA. STATEMENT OF SIGNIFICANCE: This manuscript details the first study to systematically and directly investigate the mechanism of action of antimicrobial polymers, using super-resolution fluorescence imaging as well as functional assays. While many in the field cite membrane permeation as the sole mechanism underlying the activity of such polymers, we present evidence for multimodal actions including high cellular uptake and interaction with intracellular targets. It is also the first report to show competitive binding of antimicrobial polymers with bacterial DNA in a dose-dependent manner.

Surface-Grafted Hyperbranched Polyglycerol Coating: Varying Extents of Fouling Resistance across a Range of Proteins and Cells.

Hyperbranched polyglycerol (HPG) was previously investigated as a nonfouling hydrophilic grafted layer on biomaterial surfaces, analogous to the well-known poly(ethylene oxide) (PEO), but the range of adsorbing cells and proteins tested was limited and at times the assays used were not the most sensitive. Thus, the questions arise whether HPG-grafted layers can indeed efficiently resist adsorption of a wider range of adsorbing biological entities, and how would different biological entities interact with such a coating. An HPG coating of 25 nm thickness was grafted onto a spin-coated and plasma-treated polystyrene (PS) layer on a silicon wafer substrate; this provided a well-suited system for surface analyses by X-ray photoelectron spectroscopy (XPS), time-of-flight secondary ion mass spectrometry (ToF-SIMS), and atomic force microscopy (AFM), which verified the presence of a uniform, smooth grafted HPG layer. Adsorption of bovine serum albumin, lysozyme, fibrinogen, and endothelial cell growth medium 2 (EGM2) was reduced by >90%, with the adsorbed amounts close to the detection limit of XPS but still detectable by ToF-SIMS using principal component analysis. With human serum, however, the reduction in adsorption was slightly less pronounced. Smooth muscle cells (SMCs) and fibroblasts were virtually unable to attach onto the grafted HPG layer, with >99% reductions at 6 h compared with plasma-treated PS; the few attached cells remaining rounded and unable to spread. Their attachment might have resulted from coating defects. Testing with full blood showed that unlike for the control surface (plasma-treated PS), platelets did not adhere to the HPG surface, but there was attachment of some cells that stained CD11b positive and likely are neutrophils. Cells of the fungal organism Candida albicans were also able to attach onto the HPG surface to a limited extent, but in contrast to the control surface, the attached cells on HPG did not form hyphal extensions and thus seem to be compromised in their ability to invade and to form biofilms. Our data suggest that "low-fouling" is a better term than nonfouling for a grafted HPG layer as the resistance to adsorption is not uniform across a range of proteins and cells. It is also important in future work to study whether the cells that do attach can still exert their normal functions; our observation of the absence of hyphal extensions for C. albicans suggests that this may not be so. Hence, the potential utility of a grafted HPG layer may be not just a function of adsorbed amounts but also of the functionality of adsorbed proteins and cells.

The Physics of Plasma Ion Chemistry: A Case Study of Plasma Polymerization of Ethyl Acetate.

Deposition chemistry from plasma is highly dependent on both the chemistry of the ions arriving at surfaces and the ion energy. Typically, when measuring the energy distribution of ions arriving at surfaces from plasma, it is assumed that the distributions are the same for all ionic species. Using ethyl acetate as a representative organic precursor molecule, we have measured the ion chemistry and ion energy as a function of pressure and power. We show that at low pressure (<2 Pa) this assumption is valid; however, at elevated pressures ion-molecule collisions close to the deposition surface affect both the energy and chemistry of these ions. Smaller ions are formed close to the surface and have lower energy than larger ionic species which are formed in the bulk of the plasma. The changes in plasma chemistry therefore are closely linked to the physics of the plasma-surface interface.

Interfacial Forces at Layered Surfaces: Substrate Electrical Double-Layer Forces Acting through Ultrathin Polymer Coatings.

Manipulating the surface properties of materials via the application of coatings is a widely used strategy to achieve desired interfacial interactions, implicitly assuming that the interfacial forces of coated samples are determined exclusively by the surface properties of the coatings. However, interfacial interactions between materials and their environments operate over finite length scales. Thus, the question addressed in this study is whether interactions associated with bulk substrate materials could act through thin coatings or, conversely, how thick a coating needs to be to completely screen subsurface forces contributed by underlying substrates. Plasma polymer layers were deposited on silicon wafer substrates from ethanol vapor, with identical chemical composition, ultrasmooth surfaces, and varying thicknesses. Using colloid-probe atomic force microscopy, electrical double-layer forces were determined in solutions of various ionic strengths and fitted using the Derjaguin-Landau-Verwey-Overbeek theory. For the thicker ethanol plasma polymers, the fitted surface potentials reflected the presence of surface carboxylate groups and were invariant with thickness. In contrast, for coatings <18 nm thick, the surface potentials increased steadily with decreasing film thickness; the measured electrical double-layer forces contained contributions from both the coating and the substrate. Theoretical calculations were in agreement with this model. Thus, our observations indicate that the higher surface potential of the underlying SiO2 surface can influence the interactions between a colloid particle and the multilayer structure if coatings are sufficiently thin. Such superposition needs to be factored into the design of coatings aimed at the control of material interactions via surface forces.

Antibacterial Performance of Terpenoids from the Australian Plant Eremophila lucida.

Plants in the Australian genus Eremophila (Scrophulariaceae) have attracted considerable recent attention for their antimicrobial compounds, which possess a wide range of chemical structures. As they are typically associated with the oily-waxy resin layer covering leaves and green branchlets, and Eremophila lucida is prominent among the species containing a pronounced sticky resin layer, this species was considered of interest for assessing its antibacterial constituents. The n-hexane fraction of the crude acetone extract of the leaves exhibited antibacterial activity against Staphylococcus aureus. Isolation led to the known compounds cembratriene, (3Z, 7E, 11Z)-15-hydroxycembra-3,7,11-trien-19-oic acid (1), the sesquiterpenoid, farnesal (2) and the viscidane diterpenoid, 5α-hydroxyviscida-3,14-dien-20-oic acid (3). The purified compounds were tested for antibacterial activity with 2 and 3 showing moderate antibacterial activity against Gram-positive bacteria.

Antifungal Activity in Compounds from the Australian Desert Plant Eremophila alternifolia with Potency Against Cryptococcus spp.

Plant metabolites that have shown activity against bacteria and/or environmental fungi represent valuable leads for the identification and development of novel drugs against clinically important human pathogenic fungi. Plants from the genus Eremophila were highly valued in traditional Australian Aboriginal medicinal practices, and E. alternifolia was the most prized among them. As antibacterial activity of extracts from E. alternifolia has been documented, this study addresses the question whether there is also activity against infectious fungal human pathogens. Compounds from leaf-extracts were purified and identified by 1- and 2-D NMR. These were then tested by disk diffusion and broth microdilution assays against ten clinically and environmentally relevant yeast and mould species. The most potent activity was observed with the diterpene compound, 8,19-dihydroxyserrulat-14-ene against Cryptococcus gattii and Cryptococcus neoformans, with minimum inhibition concentrations (MIC) comparable to those of Amphotericin B. This compound also exhibited activity against six Candida species. Combined with previous studies showing an antibacterial effect, this finding could explain a broad antimicrobial effect from Eremophila extracts in their traditional medicinal usage. The discovery of potent antifungal compounds from Eremophila extracts is a promising development in the search for desperately needed antifungal compounds particularly for Cryptococcus infections.

Visualizing Biomaterial Degradation by Candida albicans Using Embedded Luminescent Molecules To Report on Substrate Digestion and Cellular Uptake of Hydrolysate.

Microbial pathogens use hydrolases as a virulence strategy to spread disease through tissues and colonize medical device surfaces; however, visualizing this process is a technically challenging problem. To better understand the role of secreted fungal hydrolases and their role in Candida albicans virulence, we developed an in situ model system using luminescent Re(I) and Ir(III) containing probe molecules embedded in a biodegradable (poly(lactic-co-glycolic acid), PLGA) polymer and tracked their uptake using epifluorescent imaging. We found that secretion of esterases can explain how physically embedded probes are acquired by fungal cells through the degradation of PLGA since embedded probes could not be liberated from nonbiodegradable polystyrene (PS). It was important to verify that epifluorescent imaging captured the fate of probe molecules rather than naturally occurring fungal autofluorescence. For this, we exploited the intense luminescent signals and long spectral relaxation times of the Re and Ir containing probe molecules, resolved in time using a gated imaging system. Results provide a visual demonstration of a key virulence trait of C. albicans: the use of hydrolases as a means to degrade materials and acquire hydrolysis products during fungal growth and hyphal development. These results help to explain the role of nonspecific hydrolases using a degradable material that is relevant to the study of fungal pathogenesis on biotic (tissues) surfaces. Additionally, understanding how fungal pathogens condition surfaces by using nonspecific hydrolases is important to the study of fungal attachment on abiotic surfaces, the first step in biofilm formation on medical devices.

Surface coatings with covalently attached anidulafungin and micafungin prevent Candida albicans biofilm formation.

Objectives: Fungal biofilms caused by Candida spp. are a major contributor to infections originating from infected biomaterial implants. Since echinocandin-class molecules interfere with the integrity of the fungal cell wall, it was hypothesized that surface-immobilized anidulafungin and micafungin could play a role in preventing fungal adhesion and biofilm formation on surfaces. Methods: Anidulafungin and micafungin were covalently coupled to biomaterial surfaces and washed. Surface-sensitive instrumental analysis quantitatively and qualitatively confirmed their presence. Analysis after washing experiments provided evidence of their covalent immobilization. The in vitro antifungal properties of surfaces were confirmed using static biofilm assays and fluorescence microscopy kinetic studies. Results: Antifungal surface coatings eliminated 106 cfu/cm2 inoculations of Candida albicans and prevented biofilm formation and hyphal development on coated surfaces. Surfaces were successively exposed to fresh inoculum and were effective for at least five challenges in eliminating adherent yeasts. Conclusions: We have observed antifungal and anti-biofilm activity of surfaces bearing conjugated echinocandins, which operate through surface contact. The analytical and biological evidence suggests an antifungal mechanism for echinocandins that does not rely upon freely diffusing molecules.

QCM-D and XPS study of protein adsorption on plasma polymers with sulfonate and phosphonate surface groups.

As some proteins are known to interact with sulfated and phosphated biomolecules such as specific glycosaminoglycans, this study derives from the hypothesis that sulfonate and phosphonate groups on solid polymer surfaces might cause specific interfacial interactions. Such surfaces were prepared by plasma polymerization of heptylamine (HA) and subsequent grafting of sulfonate or phosphonate groups via Michael-type addition of vinylic compounds. Adsorption of the proteins fibrinogen, albumin (HSA) and lysozyme on these functionalised plasma polymer surfaces was studied by XPS and quartz crystal microbalance with dissipation (QCM-D). It was also studied whether pre-adsorption with HSA would lead to a passivated surface against further adsorption of other proteins. XPS confirmed grafting of vinyl sulfonate and vinyl phosphonate onto the amine surface and showed that the proteins adsorbed to saturation at between 1 and 2 h. QCM-D showed rapid and irreversible adsorption of albumin on all three surfaces, while lysozyme could be desorbed with PBS to substantial extents from the sulfonated and phosphonated surfaces but not from the amine surface. Fibrinogen showed rapid initial adsorption followed by slower additional mass gain over hours. Passivation with albumin led to small and largely reversible subsequent adsorption of lysozyme, whereas with fibrinogen partial displacement yielded a mixed layer, regardless of the surface chemistry. Thus, protein adsorption onto these sulfonated and phosphonated surfaces is complex, and not dominated by electrostatic charge effects.

Surface-grafted antimicrobial drugs: Possible misinterpretation of mechanism of action.

Antimicrobial surface coatings that act through a contact-killing mechanism (not diffusive release) could offer many advantages to the design of medical device coatings that prevent microbial colonization and infections. However, as the authors show here, to prevent arriving at an incorrect conclusion about their mechanism of action, it is essential to employ thorough washing protocols validated by surface analytical data. Antimicrobial surface coatings were fabricated by covalently attaching polyene antifungal drugs to surface coatings. Thorough washing (often considered to be sufficient to remove noncovalently attached molecules) was used after immobilization and produced samples that showed a strong antifungal effect, with a log 6 reduction in Candida albicans colony forming units. However, when an additional washing step using surfactants and warmed solutions was used, more firmly adsorbed compounds were eluted from the surface as evidenced by XPS and ToF-SIMS, resulting in reduction and complete elimination of in vitro antifungal activity. Thus, polyene molecules covalently attached to surfaces appear not to have a contact-killing effect, probably because they fail to reach their membrane target. Without additional stringent washing and surface analysis, the initial favorable antimicrobial testing results could have been misinterpreted as evidencing activity of covalently grafted polyenes, while in reality activity arose from desorbing physisorbed molecules. To avoid unintentional confirmation bias, they suggest that binding and washing protocols be analytically verified by qualitative/quantitative instrumental methods, rather than relying on false assumptions of the rigors of washing/soaking protocols.

Promiscuous hydrogen in polymerising plasmas.

Historically, there have been two opposing views regarding deposition mechanisms in plasma polymerisation, radical growth and direct ion deposition, with neither being able to fully explain the chemistry of the resultant coating. Deposition rate and film chemistry are dependent on the chemistry of the plasma phase and thus the activation mechanisms of species in the plasma are critical to understanding the relative contributions of various chemical and physical routes to plasma polymer formation. In this study, we investigate the roles that hydrogen plays in activating and deactivating reactive plasma species. Ethyl trimethylacetate (ETMA) is used as a representative organic precursor, and additional hydrogen is added to the plasma in the form of water and deuterium oxide. Optical emission spectroscopy confirms that atomic hydrogen is abundant in the plasma. Comparison of the plasma phase mass spectra of ETMA/H2O and ETMA/D2O reveals that (1) proton transfer from hydronium is a common route to charging precursors in plasma, and (2) hydrogen abstraction (activation) and recombination (deactivation) processes are much more dynamic in the plasma than previously thought. Consideration of the roles of hydrogen in plasma chemistry may then provide a more comprehensive view of deposition processes and bridge the divide between the two disparate schools of thought.

The importance of fungal pathogens and antifungal coatings in medical device infections.

In recent years, increasing evidence has been collated on the contributions of fungal species, particularly Candida, to medical device infections. Fungal species can form biofilms by themselves or by participating in polymicrobial biofilms with bacteria. Thus, there is a clear need for effective preventative measures, such as thin coatings that can be applied onto medical devices to stop the attachment, proliferation, and formation of device-associated biofilms. However, fungi being eukaryotes, the challenge is greater than for bacterial infections because antifungal agents are often toxic towards eukaryotic host cells. Whilst there is extensive literature on antibacterial coatings, a far lesser body of literature exists on surfaces or coatings that prevent attachment and biofilm formation on medical devices by fungal pathogens. Here we review strategies for the design and fabrication of medical devices with antifungal surfaces. We also survey the microbiology literature on fundamental mechanisms by which fungi attach and spread on natural and synthetic surfaces. Research in this field requires close collaboration between biomaterials scientists, microbiologists and clinicians; we consider progress in the molecular understanding of fungal recognition of, and attachment to, suitable surfaces, and of ensuing metabolic changes, to be essential for designing rational approaches towards effective antifungal coatings, rather than empirical trial of coatings.

Caspofungin on ARGET-ATRP grafted PHEMA polymers: Enhancement and selectivity of prevention of attachment of Candida albicans.

There is a need for coatings for biomedical devices and implants that can prevent the attachment of fungal pathogens while allowing human cells and tissue to appose without cytotoxicity. Here, the authors study whether a poly(2-hydroxyethylmethacrylate) (PHEMA) coating can suppress attachment and biofilm formation by Candida albicans and whether caspofungin terminally attached to surface-tethered polymeric linkers can provide additional benefits. The multistep coating scheme first involved the plasma polymerization of ethanol, followed by the attachment of α-bromoisobutyryl bromide (BiBB) onto surface hydroxyl groups of the plasma polymer layer. Polymer chains were grafted using surface initiated activators regenerated by electron transfer atom transfer radical polymerization with 2-hydroxyethylmethacrylate, yielding PHEMA layers with a dry thickness of up to 89 nm in 2 h. Hydroxyl groups of PHEMA were oxidized to aldehydes using the Albright-Goldman reaction, and caspofungin was covalently immobilized onto them using reductive amination. While the PHEMA layer by itself reduced the growth of C. albicans biofilms by log 1.4, the addition of caspofungin resulted in a marked further reduction by >4 log units to below the threshold of the test. The authors have confirmed that the predominant mechanism of action is caused by antifungal drug molecules that are covalently attached to the surface, rather than out-diffusing from the coating. The authors confirm the selectivity of surface-attached caspofungin in eliminating fungal, not mammalian cells by showing no measurable toxicity toward the myeloid leukaemia suspension cell line KG-1a.

3D printed lattices as an activation and expansion platform for T cell therapy.

One of the most significant hurdles to the affordable, accessible delivery of cell therapy is the cost and difficulty of expanding cells to clinically relevant numbers. Immunotherapy to prevent autoimmune disease, tolerate organ transplants or target cancer critically relies on the expansion of specialized T cell populations. We have designed 3D-printed cell culture lattices with highly organized micron-scale architectures, functionalized via plasma polymerization to bind monoclonal antibodies that trigger cell proliferation. This 3D technology platform facilitate the expansion of therapeutic human T cell subsets, including regulatory, effector, and cytotoxic T cells while maintaining the correct phenotype. Lentiviral gene delivery to T cells is enhanced in the presence of the lattices. Incorporation of the lattice format into existing cell culture vessels such as the G-Rex system is feasible. This cell expansion platform is user-friendly and expedites cell recovery and scale-up, making it ideal for translating T cell therapies from bench to bedside.