Effect of Different Primers on Shear Bond Strength of Base Metal Alloys and Zirconia Frameworks.

Ensuring a secure bond between a framework structure and layering composite resin veneer is essential for a long-lasting dental restoration. A variety of primer systems are available to facilitate the adhesive bonding. Nevertheless, the growing preference for efficiency and simplicity in dentistry has made the one-bottle universal primers a desirable option. This study aims to compare the effectiveness of universal primers on the shear bond strength (SBS) of base metal alloy (BMA) and zirconia to layering composite resin. Each 160 BMA and zirconia 20 × 10 × 5 mm test specimen was fabricated. Eight different primers (SunCera Metal Primer, Metal Primer Z, Reliance Metal Primer, Alloy Primer, MKZ Primer, Monobond Plus, ArtPrime Plus, and Clearfil Ceramic Primer Plus) were applied to 20 specimens in each group. Subsequently, a 5 × 2 mm composite resin build-up was applied. SBS tests were performed after 24 h of water storage and after thermocycling (25,000 cycles, 5-55 °C). On BMA, after water storage for 24 h, the bond strength values ranged from 26.53 ± 3.28 MPa (Metal Primer Z) to 29.72 ± 2.00 MPa (MKZ Primer), while after thermocycling, bond strength values ranged from 25.19 ± 1.73 MPa (MKZ Primer) to 27.69 ± 2.37 MPa (Clearfil Ceramic Primer Plus). On a zirconia base, after 24 h, the bond strengths values ranged from 22.63 ± 2.28 MPa (Reliance Primer) to 29.96 ± 2.37 MPa (MKZ Primer) and from 23.77 ± 3.86 MPa (Metal Primer Z) to 28.88 ± 3.09 MPa (Monobond Plus) after thermocycling. While no significant difference in bond strength was found between the primers on the BMA base, five primer combinations differed significantly from each other on zirconia (p = 0.002-0.043). All primers achieved a bond strength greater than 23 MPa on both framework materials after thermocycling. Thus, all primers tested can be applied to both framework materials with comparable results.

Association between periodontal health status and quality of life: a cross-sectional study.

Introduction: Attachment loss due to periodontal diseases is associated with functional limitations as well as physical pain and psychological discomfort, which may lead to a reduced quality of life. The purpose of this study is to determine if the oral health status, specifically the periodontal status, influences oral health-related quality of life. Materials and methods: Survey data were collected in a US dental school clinical setting in a cross-sectional study. Quality of life related to oral health was assessed with the Oral Health Impact Profile-49 (OHIP-49). In addition, DMFT index, periodontal status, and health literacy scores (dental and medical health literacy) were recorded, and the data of n = 97 subjects were statistically analyzed. Results: The DMFT index of the study population was 14.98 ± 6.21 (D: 4.72 ± 4.77; M: 3.19 ± 3.46; F: 7.12 ± 4.62). Of the subjects, 44% were identified as periodontitis cases. These periodontitis cases demonstrated significantly higher OHIP-49 scores (66.93 ± 30.72) than subjects without signs of periodontal diseases (NP) (32.40 ± 19.27, p < 0.05). There was also a significant difference between NP patients and patients with gingivitis (66.24 ± 46.12, p < 0.05). It was found that there was a statistically significant difference between Stage 3 (severe) periodontitis and periodontal health (p = 0.003). Pearson correlations were completed, and positive relationships were found with OHIP-49 and DMFT (0.206, p < 0.05), and periodontal risk self-assessment (0.237, p < 0.05). Age [odds ratio (OR) 4.46], smoking (OR 2.67), and the presence of mobile teeth (OR 2.96) are associated with periodontitis. Conclusions: Periodontal diseases may negatively impact the oral health-related quality of life. Patients suffering from periodontitis also showed more missing teeth, which might influence function. Age and smoking are associated with a higher prevalence of periodontitis. A good general health literacy was no guarantee for having an adequate oral literacy.

An in vitro analysis of the accuracy of static and robot-assisted implant surgery.

OBJECTIVES: Robot-assisted implant surgery (RAIS) is purported to improve the accuracy of implant placement. The objective of this study was to compare RAIS with static computer-assisted implant surgery (sCAIS) in a controlled environment. MATERIALS AND METHODS: A total of n = 102 implants were placed in the same modified typodont (n = 17 repeated simulated implant surgeries with each n = 3 implants per group) using robot-assisted or static computer-assisted implant surgery. The final implant positions were digitized utilizing cone-beam tomography and compared with the planned position. The angular deviation was the primary outcome parameter. 3D deviations at the implant platform level and the apex were secondary outcome parameters. Accuracy in terms of trueness and precision were assessed. Means, standard deviation, and 95%-confidence intervals were analyzed statistically. RESULTS: The overall angular deviation was 2.66 ± 1.83° for the robotic system and 0.68 ± 0.38° for guided surgery using static guides (p < .001), the 3D-deviation of the implant platform at crest level was for sCAIS 0.79 ± 0.28 mm and RAIS 1.51 ± 0.53 mm (p < .001) and at the apex for sCAIS 0.82 ± 0.26 mm and for RAIS 1.97 ± 0.79 mm (p < .001), respectively. CONCLUSIONS: Robotically guided implant surgery was less accurate in terms of trueness (planned vs. actual position) and precision (deviations among implants) than traditional static computer-assisted implant surgery in this in vitro study.

Functional Load Capacity of Teeth with Reduced Periodontal Support: A Finite Element Analysis.

The purpose of this study was to investigate the functional load capacity of the periodontal ligament (PDL) in a full arch maxilla and mandible model using a numerical simulation. The goal was to determine the functional load pattern in multi- and single-rooted teeth with full and reduced periodontal support. CBCT data were used to create 3D models of a maxilla and mandible. The DICOM dataset was used to create a CAD model. For a precise description of the surfaces of each structure (enamel, dentin, cementum, pulp, PDL, gingiva, bone), each tooth was segmented separately, and the biomechanical characteristics were considered. Finite Element Analysis (FEA) software computed the biomechanical behavior of the stepwise increased force of 700 N in the cranial and 350 N in the ventral direction of the muscle approach of the masseter muscle. The periodontal attachment (cementum-PDL-bone contact) was subsequently reduced in 1 mm increments, and the simulation was repeated. Quantitative (pressure, tension, and deformation) and qualitative (color-coded images) data were recorded and descriptively analyzed. The teeth with the highest load capacities were the upper and lower molars (0.4-0.6 MPa), followed by the premolars (0.4-0.5 MPa) and canines (0.3-0.4 MPa) when vertically loaded. Qualitative data showed that the areas with the highest stress in the PDL were single-rooted teeth in the cervical and apical area and molars in the cervical and apical area in addition to the furcation roof. In both single- and multi-rooted teeth, the gradual reduction in bone levels caused an increase in the load on the remaining PDL. Cervical and apical areas, as well as the furcation roof, are the zones with the highest functional stress. The greater the bone loss, the higher the mechanical load on the residual periodontal supporting structures.

An in-vitro analysis of the accuracy of different guided surgery systems - They are not all the same.

OBJECTIVES: Different static computer-assisted implant surgery (sCAIS) systems are available that are based on different design concepts. The objective was to assess seven different systems in a controlled environment. MATERIALS AND METHODS: Each n = 20 implants were placed in identical mandible replicas (total n = 140). The systems utilized either drill-handles (group S and B), drill-body guidance (group Z and C), had the key attached to the drill (group D and V), or combined different design concepts (group N). The achieved final implant position was digitized utilizing cone-beam tomography and compared with the planned position. The angular deviation was defined as the primary outcome parameter. The means, standard deviation, and 95%-confidence intervals were analyzed statistically with 1-way ANOVA. A linear regression model was applied with the angle deviation as predictor and the sleeve height as response. RESULTS: The overall angular deviation was 1.94 ± 1.51°, the 3D-deviation at the crest 0.54 ± 0.28 mm, and at the implant tip 0.67 ± 0.40 mm, respectively. Significant differences were found between the tested sCAIS systems. The angular deviation ranged between 0.88 ± 0.41° (S) and 3.97 ± 2.01° (C) (p < .01). Sleeve heights ≤4 mm are correlated with higher angle deviations, sleeve heights ≥5 mm with lower deviations from the planned implant position. CONCLUSIONS: Significant differences were found among the seven tested sCAIS systems. Systems that use drill-handles achieved the highest accuracy, followed by the systems that attach the key to the drill. The sleeve height appears to impact the accuracy.

Wear pattern-associated color stability of prefabricated composite veneers versus ceramic veneers.

PURPOSE: To evaluate the effect of different surface wear patterns on the discoloration tendency of two different prefabricated composite veneers and lithium disilicate ceramic veneers. MATERIALS AND METHODS: Discoloration tendency of two prefabricated composite resin veneers (Visalys Veneer Chairside (VIS) and Componeer (COM)) were compared to lithium disilicate veneers (IPS) in vitro. For each material, n = 60 samples were allocated to different test groups, and therefore each n = 10 specimens per group went through different wear tests. Mechanical abrasion tests were conducted using a toothbrush simulator, while erosive effects were carried out by citric acid (pH 1.57). A combination of abrasion and erosion tests was conducted as well. Four groups of wear tests were implemented: (1) abrasion, (2) abrasion followed by erosion, (3) erosion, and (4) erosion followed by abrasion. Another group was stored in distilled water as the control and one group was stained without a prior wear test. The staining solution was made from a coffee-tobacco brew. Specimens were stored in the coffee-tobacco solution for 21 days. Color measurements were performed with VITA Easyshade. To evaluate intramaterial discoloration, one half of every specimen was protected with foil. After storage in the staining solution, the first measurement was carried out on the 'protected' (untreated) surface, followed by a second measurement on the 'processed' (treated) discolored surface. Euclidean distance (ΔE) of discoloration was calculated according to the CIE-L*C*h* system. Data were analyzed with ANOVA followed by Games-Howell post hoc test and paired t-test (α = 0.05). RESULTS: Highest changes in ΔE were found in COM after 'abrasion' (ΔE -2.55) and 'erosion followed by abrasion' (ΔE -1.41). The discoloration tendency of VIS was affected by all wear tests, but changes were below the perceptive threshold (ΔE -0.19-0.32). Only abrasion followed by erosion affected the discoloration of IPS significantly, but findings were below the perceptive threshold, as well (ΔE -0.09). CONCLUSIONS: Prefabricated composite resin veneers revealed a low level of discoloration tendency after different wear tests. Nevertheless, in most cases the lowest discoloration tendency was found in specimens made from lithium disilicate.

Effect of Individualized Oral Health Care Training Provided to 6-16-Year-Old Psychiatric In-Patients-Randomized Controlled Study.

BACKGROUND: To assess the effect of individualized oral health care training (IndOHCT) administered to 6-16-year-old psychiatric in-patients on dental plaque removal. METHODS: 74 in-patients with mental health disorders (49 males) aged 6-16 years with a mean age of 10.4 ± 2.3 years, were randomly divided into two equal groups. At the start of hospitalization, one calibrated dentist assessed the oral health status in the hospital setting. In-patients of the intervention group (IG) received IndOHCT, while those of the control group (CG) got an information flyer. Dental plaque was assessed by the Turesky modified Quigley-Hein-Index (TI) at the start (t0) and at the end of hospitalization before (t1a) and after (t1b) autonomous tooth brushing. RESULTS: During hospitalisation, the TI was reduced in both groups (t0→t1a: IG = -0.1; CG = -0.2, p = 0.71). However, in-patients receiving IndOHCT achieved significantly higher plaque reduction rates than the controls when plaque values before and after autonomous tooth brushing were compared (t1a→t1b: IG = -1.0; CG = -0.8; p = 0.02). The effect size (ES) demonstrates the efficacy of IndOHCT (ES = 0.53), especially in children with mixed dentition (ES = 0.89). CONCLUSIONS: IndOHCT enabled hospitalized children and adolescents with mental health disorders to achieve a better plaque reduction by tooth brushing but failed to improve self-controlled routine oral hygiene.

Precision and trueness of computer-assisted implant placement using static surgical guides with open and closed sleeves: An in vitro analysis.

OBJECTIVES: The aim of this in vitro study was to determine accuracy defined by trueness and precision of computer-assisted implant surgery comparing two guided surgery kits designed for either closed sleeves or open sleeves with a lateral window. MATERIAL AND METHODS: Each n=20 implants were placed fully guided (sleeve-bone distance of 2 or 4 mm) in identical replicas using a surgical guide with both closed sleeve or an open sleeve, partially guided, or free hand. The achieved implant position was digitized and compared with the planned position. Trueness and precision were determined. The angular deviation was defined as the primary outcome parameter. The means, standard deviation, and 95%-confidence intervals were analyzed statistically with 1-way ANOVA and the Scheffé procedure. RESULTS: The accuracy of guided implant placement using closed and open sleeves was comparable when the sleeve-bone distance was 2 mm. Accuracy decreased when the sleeve-bone distance increased in both fully guided groups, more so in the open than in the closed sleeve group. The least accurate method was the free-hand group. Partially guided implant surgery was more accurate than free-hand placement, but less accurate than the fully guided groups with 2-mm sleeve-bone distance. CONCLUSIONS: The closer the sleeve to the bone, the more accurate and precise is computer-assisted implant surgery using a closed system and a system using open sleeves. Partially guided implant surgery using only the static guide for the pilot drill is less accurate than both fully guided approaches, but more accurate than free-hand surgery.

Inhibition of Candida albicans and Mixed Salivary Bacterial Biofilms on Antimicrobial Loaded Phosphated Poly(methyl methacrylate).

Biofilms play a crucial role in the development of Candida-associated denture stomatitis. Inhibition of microbial adhesion to poly(methyl methacrylate) (PMMA) and phosphate containing PMMA has been examined in this work. C. albicans and mixed salivary microbial biofilms were compared on naked and salivary pre-conditioned PMMA surfaces in the presence or absence of antimicrobials (Cetylpyridinium chloride [CPC], KSL-W, Histatin 5 [His 5]). Polymers with varying amounts of phosphate (0-25%) were tested using four C. albicans oral isolates as well as mixed salivary bacteria and 24 h biofilms were assessed for metabolic activity and confirmed using Live/Dead staining and confocal microscopy. Biofilm metabolism was reduced as phosphate density increased (15%: p = 0.004; 25%: p = 0.001). Loading of CPC on 15% phosphated disks showed a substantial decrease (p = 0.001) in biofilm metabolism in the presence or absence of a salivary pellicle. Salivary pellicle on uncharged PMMA enhanced the antimicrobial activity of CPC only. CPC also demonstrated remarkable antimicrobial activity on mixed salivary bacterial biofilms under different conditions displaying the potent efficacy of CPC (350 µg/mL) when combined with an artificial protein pellicle (Biotene half strength).

Influence of Progressive Versus Minimal Canal Preparations on the Fracture Resistance of Mandibular Molars: A 3-Dimensional Finite Element Analysis.

INTRODUCTION: This study compared the residual tooth strength and stress distribution of a mandibular molar prepared with different variable tapered file systems using finite element analysis (FEA). METHODS: Two preaccessed mandibular molar TruTeeth (Endo 3DP; Acadental, Lenexa, KS) were subjected to simulated endodontic treatment in this study. One tooth was instrumented with ProTaper Gold (Dentsply Tulsa Dental Specialties, Tulsa, OK), and the other was instrumented with V-Taper 2H (SS White Dental, Lakewood, NJ). The 2 teeth were scanned using micro-computed tomographic imaging, and stereolithographic surface meshes were developed for FEA. Each model was subjected to a 200-N multipoint load-simulating mastication. The results of the FEA provided quantitative and qualitative measurements for von Mises stress distribution and total deformation. RESULTS: The maximum von Mises stress was greater in the ProTaper Gold-prepared model than the V-Taper 2H prepared model. In both models, total deformation values were highest in the clinical crown on the buccal aspect of the tooth. The highest stress values were found in the pericervical dentin, and stress decreased apically through the root. CONCLUSIONS: Within the limitations of this study, it can be concluded that the maximum stress values within the tooth prepared by ProTaper Gold were higher than those in the tooth prepared by V-Taper 2H. Canal preparation with the V-Taper 2H system preserves more pericervical dentin, which may increase the resistance to fracture.

Comparison of Wear Resistance of Prefabricated Composite Veneers Versus Ceramic and Enamel.

PURPOSE: To measure surface roughness before and after wear-tests of two different prefabricated composite veneers and compare them to ceramic veneers and human dental enamel. MATERIALS AND METHODS: Roughness (Ra-values) of two prefabricated composite veneers (Visalys Veneer Chairside (VIS) and Componeer (COM)) were compared to lithium disilicate Veneers (e.max CAD) and dental enamel (DENT) in vitro. In total n = 45 specimens per material and enamel samples were used for wear-tests. Wear-out tests were conducted by abrasion tests with a toothbrush simulator (22,000 strokes/ 100 g load; approximately equal to two years of cleansing) and erosion tests were carried out using citric acid (pH 1.57). Ra- and Sa-values were detected by white light interferometer before and after wear-tests. Data were analyzed with ANOVA followed by Games-Howell post hoc test and t-test (α = 0.05). RESULTS: At baseline the lowest Ra- and Sa-values were found in VIS (Ra: 0.01 µm; Sa: 0.04 µm) while DENT revealed significantly higher surface roughness (Ra: 0.11 µm, p < 0.05; Sa: 0.30, p = 0.186). COM had significantly higher Ra-values (Ra: 0.10 µm; Sa: 0.22 µm) after abrasion, while e.max CAD was most resistant to the treatments (Ra: 0.01 µm, p < 0.05; Sa: 0.05 µm, p < 0.05). Compared to DENT all veneers were significantly less affected by citric acid (p < 0.001). CONCLUSIONS: Prefabricated composite veneers have demonstrated less wear after abrasion and erosion tests compared to DENT, nevertheless, they revealed more wear compared to e.max CAD.

Antibiotics against Periodontal Biofilms.

The systemic administration of antibiotics in conjunction with mechanical biofilm disruption results in reduced numbers of subgingival periodontal pathogens and improved clinical outcomes. Penicillins, tetracyclines, macrolides, quinolones, and nitroimidazoles were used in laboratory and clinical studies. The current literature was reviewed and studies investigating the effect of antibiotics on periodontal pathogens in biofilm models or in clinical trials were analyzed. While there is only a limited number of in vitro studies, numerous clinical studies reported microbiological outcomes. The combination of amoxicillin and metronidazole seems to provide superior antimicrobial effects when used in biofilm models or in clinical trials. In vitro studies using biofilm models showed that antibiotics alone have only limited effects on the bacterial load in biofilms but might be effective in reducing specific species. These results imply that mechanical biofilm disruption is indicated to allow antibiotics to be effective. Clinical trials also demonstrated that the combination therapy of amoxicillin and metronidazole might result in more superior microbiological effects than amoxicillin or metronidazole alone. The results of clinical studies investigating azithromycin are contrary. While it seems to be appropriate to use in chronic periodontitis (comparable to the new classification: stage 3 or 4, grade B generalized periodontitis), there was no superior effect observed in aggressive periodontitis (comparable to the new classification: stage 3 or 4, grade C generalized periodontitis). Doxycycline cannot be recommended for chronic periodontitis (stage 3 or 4, grade B) patients. Antibiotics as drugs come with side effects. Common adverse effects of antibiotics are opportunistic yeast infection and gastrointestinal complications (e.g., nausea, diarrhea, and colitis). The development of resistance suggests a role for microbiological analysis and antibiotic susceptibility testing in the selection of systemic periodontal antibiotic therapy.

Precision and trueness of implant placement with and without static surgical guides: An in vitro study.

STATEMENT OF PROBLEM: Malpositioning of implants is one of the main factors leading to hard- and soft-tissue deficiencies. Whether static computer-guided implant placement increases accuracy and prevents malpositioning is unclear. PURPOSE: The purpose of this in vitro study was to determine accuracy defined by trueness and precision (according to International Organization for Standardization 5725) of computer-assisted implant surgery (fully guided and partially guided) in comparison with freehand single implant placement. MATERIAL AND METHODS: Implants (n=20) were placed fully guided (sleeve-bone distance of 2, 4, or 6 mm), partially guided (guide used for pilot drill), or free hand in identical replicas produced from a cone beam computed tomography (CBCT) scan of a partially edentulous patient. The achieved implant position was digitized by using a laboratory scanner and compared with the planned position. Trueness (planned versus actual position) and precision (difference among implants) were determined. The 3D-offset at the crest of the implant (root mean square between virtual preoperative planning and postoperative standard tessellation language file) was defined as the primary outcome parameter. The means, standard deviation, and 95% confidence intervals were analyzed statistically with 1-way ANOVA and the Scheffé procedure. RESULTS: Fully guided implant surgery achieved significantly lower 3D deviations between the planned and actual implant position with 0.22 ±0.07 mm (2-mm sleeve-bone distance) than partially guided 0.69 ±0.15 mm and freehand placement 0.80 ±0.35 mm at the crest (P<.001). The distance among the implants in each group was again lowest in the fully guided group and highest in the freehand group. CONCLUSIONS: The static computer-assisted implant surgery showed high trueness and precision. The closer the sleeve to the bone, the more accurate and precise the method. Freehand implant placement was less accurate and precise than computer-assisted implant surgery (partially or fully).

Effect of biomimetic mineralization on enamel and dentin: A Raman and EDX analysis.

OBJECTIVE: To investigate the effect of an experimental biomimetic mineralization kit (BIMIN) on the chemical composition and crystallinity of caries-free enamel and dentin samples in vitro. METHODS: Enamel and dentin samples from 20 human teeth (10 for enamel; 10 for dentin) were divided into a control group without treatment and test samples with BIMIN treatment. Quantitative analysis of tissue penetration of fluoride, phosphate, and calcium was performed using energy-dispersive X-ray spectroscopy (EDX). Mineralization depth was measured by Raman spectroscopy probing the symmetric valence vibration near 960cm-1 as a marker for crystallinity. EDX data was statistically analyzed using a paired t-test and Raman data was analyzed using the Student's t-test. RESULTS: EDX analysis demonstrated a penetration depth of fluoride of 4.10±3.32µm in enamel and 4.31±2.67µm in dentin. Calcium infiltrated into enamel 2.65±0.64µm and into dentin 5.58±1.63µm, while the penetration depths for phosphate were 4.83±2.81µm for enamel and 6.75±3.25µm for dentin. Further, up to 25µm of a newly mineralized enamel-like layer was observed on the surface of the samples. Raman concentration curves demonstrated an increased degree of mineralization up to 5-10µm into the dentin and enamel samples. SIGNIFICANCE: Biomimetic mineralization of enamel and dentin samples resulted in an increase of mineralization and a penetration of fluoride into enamel and dentin.

Comparison of Gingival Retraction Materials Using a New Gingival Sulcus Model.

PURPOSE: To investigate the pressure generated by different retraction materials using a novel gingival sulcus model. MATERIALS AND METHODS: A gingival sulcus model was made using a polymer frame filled with silicon. A pressure sensor and a sulcus-fluid simulation were embedded into the silicon chamber to evaluate the pressure generated by different retraction materials. Six sizes of Ultrapak retraction cords (Ultradent, sizes #000 - 3), 4 retraction pastes (Expazen, Expasyl, Acteon, Access Edge, Traxodent) and 2 retraction gels (Sulcus Blue, Racegel) were analyzed. The mean and median pressure, interquartile range, and standard deviation (SD) of n = 10 repeated measurements were calculated. Statistical analysis was conducted by Kruskal-Wallis test for differences between the main groups of retraction materials, and Mann-Whitney U-test was performed to analyze differences between the single retraction materials. RESULTS: Pressure (mean ± SD) generated by retraction cords increased with increasing size (48.26 ± 11.29 kPa, size #000 to 149.27 ± 28.75 kPa for #3). There was a significant difference between sizes (p < 0.01), except in #0 versus #1, and #2 versus #3. Retraction pastes generated pressures that ranged from 82.74 ± 29.29 kPa (Traxodent) to 524.35 ± 113.88 kPa (Expasyl). Retraction gels generated pressures from 38.96 ± 14.68 kPa (Racegel) to 95.15 ± 24.18 kPa (Sulcus Blue). Pressure generated by Expasyl was significantly higher than pressure generated by all other tested materials (p < 0.001). CONCLUSION: Pressure generated by retraction pastes and gels depends on the consistency of the retraction material, while pressure generated by retraction cords increased with increasing size of cords. Expasyl was found to generate the highest pressure compared to all other retraction materials.

Quality of Postoperative Pain Management After Maxillofacial Fracture Repair.

BACKGROUND: Effective pain management is an essential component in the perioperative care of surgical patients. However, postoperative pain after maxillofacial fracture repair and its optimal therapy has not been described in detail. MATERIALS AND METHODS: In a prospective cohort study, 95 adults rated their pain on the first postoperative day after maxillofacial fracture repair using the questionnaire of the Quality Improvement in Postoperative Pain Management (QUIPS) project. Quality Improvement in Postoperative Pain Management allowed for a standardized assessment of patients' characteristics and pain-related parameters. RESULTS: Overall, the mean maximal pain and pain on activity (numeric rating scales) were significantly higher in patients with mandibular fractures than in patients with midface fractures (P = 0.002 and P = 0.045, respectively). In patients with mandibular fractures, a longer duration of surgery was significantly associated with higher satisfaction with pain intensity (P = 0.015), but was more frequently associated with postoperative vomiting (P = 0.023). A shorter duration of surgery and an absence of preoperative pain counseling in these patients were significantly correlated to desire for more pain medication (P = 0.049 and P = 0.004, respectively). Patients with mandibular fractures that received opioids in the recovery room had significantly higher strain-related pain (P = 0.017). In patients with midface fractures, a longer duration of surgery showed significantly higher levels of decreased mobility (P = 0.003). Patients receiving midazolam for premedication had significantly less minimal pain (P = 0.021). CONCLUSIONS: Patients with mandibular fractures seem to have more postoperative pain than patients with midface fractures. Monitoring of postsurgical pain and a procedure-specific pain-treatment protocol should be performed in clinical routine.

Bilateral sagittal split osteotomy-parameters and correlations of postoperative pain management.

OBJECTIVES: Postoperative pain management is of utmost interest for patients undergoing orthognathic surgery. Currently, there is a lack of information regarding process and outcome parameters of postoperative pain management after bilateral sagittal split osteotomy. MATERIALS AND METHODS: In a prospective clinical study, 31 adults were evaluated on the first postoperative day following bilateral sagittal split osteotomy using the standardized questionnaire of the Germany-wide project Quality Improvement in Postoperative Pain Management (QUIPS). It allows a standardized assessment of patients' characteristics, pain parameters, outcome, and pain therapy process parameters. RESULTS: Pain management consisted mainly of premedication with midazolam, sufentanil, and metamizol intraoperatively; piritramide in the recovery room; and metamizol and tramadol on ward. Twenty patients (64.5%) showed inadequate pain management with pain levels ≥4. Patients receiving tramadol as opioid on ward presented significantly higher maximum pain levels (p = .037). Significantly lower satisfaction with postoperative pain intensity (p > .001) and significantly higher desire for additional pain medication (p = .023) were detected, when duration of surgery was above the median of 107.5 min. CONCLUSIONS: Inadequate pain management on the first postoperative day following bilateral sagittal split osteotomy was widespread on our ward. QUIPS helped us to identify it and thereby gave us the possibility to improve the situation. Prolonged duration of surgery seems to be a predictor of an elevated postoperative pain medication demand. CLINICAL RELEVANCE: Only the establishment of an ongoing monitoring of postoperative pain management can help to reduce or even avoid inadequate postoperative pain management. In accordance to the existing literature, we found inadequate postoperative pain management more widespread than thought.

Cross-Sectional Study of four Serological Bone Turnover Markers for the Risk Assessment of Medication-Related Osteonecrosis of the Jaw.

BACKGROUND: Despite the benefits related to the use of bisphosphonates and denosumab, medication-related osteonecrosis of the jaw (MRONJ) is a serious complication. The purpose of this study was to investigate the utility of 4 biochemical markers including serum c-terminal telopeptide cross-link of type I collagen (s-CTX), serum osteocalcin (s-OC), serum parathormon (s-PTH), and serum bone-specific alkaline phosphatase (s-BAP) as useful clinical tools to help assess the risk for MRONJ prior to invasive oral surgery. MATERIALS AND METHODS: Twenty patients diagnosed with MRONJ and 20 controls who have been on antiresorptive therapies with no occurrence of MRONJ were included in this 2-arm cross-sectional study. The s-CTX, s-OC, s-PTH, and s-BAP values were measured. Mann-Whitney U test compared the s-CTX, s-OC, s-PTH, and s-BAP values of the MRONJ group and the controls (P < 0.05). RESULTS: Lower values were observed in the MRONJ group compared with the control group for s-CTX (130.00 pg/mL versus 230.0 pg/mL; P = 0.12) and for s-OC (10.6 ng/mL versus 14.80 ng/mL; P = 0.051) both without significance and for s-BAP (0.23 µkat/L versus 0.31 µkat/L; P = 0.002) with significance. By contrast, the median s-PTH value of the MRONJ group was higher (30.65 ng/L versus 25.50 ng/L; P = 0.89), but without significance. CONCLUSIONS: The evaluation of the 4 biochemical markers showed that only the value of s-BAP was significantly decreased in the MRONJ patients compared with the controls. Presently, because of the lack of evidence, a routine check prior to oral surgery for the risk assessment of MRONJ cannot be recommended.

Salivary MMP-9 in the detection of oral squamous cell carcinoma

BACKGROUND: Oral squamous cell carcinoma (OSCC) is the most common malignant tumour of the oral cavity. Detection of OSCC is currently based on clinical oral examination combined with histopathological evaluation of a biopsy sample. Direct contact between saliva and the oral cancer makes measurement of salivary metalloproteinase- 9 (MMP-9) an attractive alternative. MATERIAL AND METHODS: In total, 30 OSCC patients and 30 healthy controls were included in this prospective study. Saliva samples from both groups were collected, centrifuged and supernatant fluid was subjected to ELISA for assessment of MMP-9. The median salivary MMP-9 values with interquartile range (IQR) of OSCC patients and the control group were statistically analysed using the Mann-Whitney U-test. The receiver operating characteristic (ROC) curve was constructed and the area under curve (AUC) was computed. RESULTS: The median absorbance MMP-9 value of the OSCC group was 0.186 (IQR = 0.158) and that of control group was 0.156 (IQR = 0.102). MMP-9 was significantly increased in the OSCC patients than in the controls by +19.2% (p = 0.008). Median values in patients with recurrence and in patients with primary event were 0.233 (IQR = 0.299) and 0.186 (IQR = 0.134) respectively. MMP-9 was significantly increased in patients with primary event (p = 0.017) compared to controls by +19.2%. No significant increase of MMP-9 level was detected when comparing patients with recurrence and healthy controls (+49.4%; p = 0.074). The sensitivity value of MMP-9 was 100% whereas the specificity value was 26.7% with AUC of 0.698. CONCLUSIONS: The present data indicates that the elevation of salivary levels of MMP-9 may be a useful adjunctive diagnostic tool for detection of OSCC. However, further studies are necessary to provide scientific and clinical validation