Recycled Precast Concrete Kerbs and Paving Blocks, a Technically Viable Option for Footways.

The linear economy paradigm in place to date has to be seriously challenged to give way to a new school of thought known as the circular economy. In this research work, precast kerbs and paving blocks made with recycled concrete (RACC-mixture) bearing 50 wt% mixed recycled aggregate (masonry content of 33%) and an eco-efficient cementitious material as 25 wt% conventional binder replacement were evaluated to assess their intrinsic potential to replace traditional raw materials, in keeping with circular economy criteria. Therefore, precast products were subjected to mechanical strength, durability and microstructure tests and were compared to conventional concrete units (CC-mixture and commercially available precast elements). Although a class demotion was observed for water absorption and some decreases in flexural strength (26%), splitting tensile strength (12.8%) and electrical resistivity (45%) and a lower class water absorption were registered, and the recycled mixture also exhibited a greater performance in terms of compressive strength (6%), a better abrasion resistance classification and a comparable porosity and microstructure, which ensures a good concrete durability. In any case, the results showed that precast pieces were European standard-compliant, thus supporting the viability of the mixed recycled aggregates and eco-efficient cementitious replacement in footways.

Use of Mixed Microbial Cultures to Protect Recycled Concrete Surfaces: A Preliminary Study.

One approach to tackle the problems created by the vast amounts of construction and demolition waste (CDW) generated worldwide while at the same time lengthening concrete durability and service life is to foster the use of recycled aggregate (RA) rather than natural aggregate (NA). This article discusses the use of polyhydroxyalkanoates (PHAs)-producing mixed microbial cultures (MMCs) to treat the surface of recycled concrete with a view to increase its resistance to water-mediated deterioration. The microorganisms were cultured in a minimal medium using waste pinewood bio-oil as a carbon source. Post-application variations in substrate permeability were determined with the water drop absorption and penetration by water under pressure tests. The significant reduction in water absorption recorded reveals that this bioproduct is a promising surface treatment for recycled concrete.

Use of Bioproducts Derived from Mixed Microbial Cultures Grown with Crude Glycerol to Protect Recycled Concrete Surfaces.

The large increase in the world population has resulted in a very large amount of construction waste, as well as a large amount of waste glycerol from transesterification reactions of acyl glycerides from oils and fats, in particular from the production of biodiesel. Only a limited percentage of these two residues are recycled, which generates a large management problem worldwide. For that reason, in this study, we used crude glycerol as a carbon source to cultivate polyhydroxyalkanoates (PHA)-producing mixed microbial cultures (MMC). Two bioproducts derived from these cultures were applied on the surface of concrete with recycled aggregate to create a protective layer. To evaluate the effect of the treatments, tests of water absorption by capillarity and under low pressure with Karsten tubes were performed. Furthermore, SEM-EDS analysis showed the physical barrier caused by biotreatments that produced a reduction on capillarity water absorption of up to 20% and improved the impermeability of recycled concrete against the penetration of water under pressure up to 2.7 times relative to the reference. Therefore, this bioproduct shown to be a promising treatment to protect against penetration of water to concrete surfaces increasing its durability and useful life.

Influence of the use of External Carbon Fiber Reinforcement on the Flexural Behavior of Prismatic Concrete Test Specimens. An Application for Repairing of Deteriorated Agricultural Structures.

This manuscript reports a study of the capacity of polymer composites to increase flexural strength in concrete. The polymer composites reinforced with carbon fiber and bonded with epoxy adhesive were used in prismatic test specimens of mass concrete corresponding to two different morphologies. The aim was to simulate the restoration of deteriorating concrete agricultural structures in order to explore the viability of this alternative against replacing them. An increase was found in the strength of the elements tested, with a higher strength being observed in those test specimens presenting a modified geometry.

Paving with Precast Concrete Made with Recycled Mixed Ceramic Aggregates: A Viable Technical Option for the Valorization of Construction and Demolition Wastes (CDW).

This research aimed to prove the feasibility of producing two types of precast elements widely used in construction, such as curbstones and paving blocks, using recycled concrete made with a 50% substitution of the natural gravel by recycled mixed aggregates with a significant ceramic content (>30%). In order to prove the quality of such mass concrete recycled precast elements, two different mixes were used: the first one was a conventional concrete mix provided by Prefabricados de Hormigón Pavimentos Páramo S.L., one of the collaborating companies in this study, and the other was a mixture in which wt 50% of the natural coarse aggregates were substituted for recycled mixed aggregates ceramic (RMAc). This recycled aggregate is a heterogeneous mixture of unbound aggregates, concrete, ceramic, etc., used as a secondary recycled aggregate and commonly produced in a lot of recycling plants in many European countries. This material was supplied by Tecnología y Reciclado S.L., the other collaborating company. Both mixtures were representative in order to establish the comparative behavior between them, taking into account that smaller percentages of replacement of the natural with recycled aggregates will also produce good results. This percentage of substitution represents a high saving of natural resources (gravel) and maintains a balanced behavior of the recycled concrete, so this new material can be considered to be a viable and reliable option for precast mass concrete paving elements. The characterization of the recycled precast elements, covering mechanical, microstructural, and durability properties, showed mostly similar behavior when compared to the analogous industrially-produced pieces made with conventional concrete.