Evaluation of adhesive properties and enzymatic activity at the hybrid layer of a simplified adhesive loaded with 0.2 % Cu and 5 % ZnO nanoparticles: A Randomized Clinical Trial and ex vivo analysis.

OBJECTIVE: The aim of this study was to evaluate the effect of an adhesive loaded with 0.2 % copper (Cu) and 5 % zinc oxide (ZnO) nanoparticles (Nps) on its adhesive properties and enzymatic activity at the hybrid layer ex vivo in a randomized clinical model. METHODS: Fifteen patients participated in this study, and a total of 30 third molars were used. Occlusal cavities (4 × 4 × 2 mm) were made in each tooth, and randomly divided into 2 groups: (i) Experimental group: commercial adhesive loaded with 0.2wt % CuNps and 5wt % ZnONps; and (ii) Control Group: non-loaded commercial adhesive. Teeth were restored with resin composite. Thirty days later, extractions were performed. Extracted teeth were longitudinally sectioned. Nps in powder were characterized by field emission scanning electron microscope (FE-SEM) and energy dispersive X-ray (EDX) analysis. Microtensile bond strength (µTBS), degree of conversion (DC), and nanoleakeage (NL) tests were executed. In situ zymography (Zym) was performed to evaluate the gelatinolytic activity at the hybrid layer. Student's t-test (α = 0.05) was applied for all tests. RESULTS: µTBS and DC did not show significant differences (p > 0.05) between both groups. However, NL and gelatinolytic activity at the hybrid layer showed significant values (p < 0.05) for experimental group in comparison with control group. CONCLUSION: The addition of 0.2 % CuNps and 5 % ZnONps to a universal adhesive decreases NL and gelatinolytic activity at the hybrid layer, without jeopardizing its adhesive properties. SIGNIFICANCE: This randomized clinical trial with ex vivo analysis demonstrate that a commercial adhesive modified with 0.2wt % Cu and 5wt % ZnO Nps that does not affect its adhesive properties, reducing gelatinolytic activity and nanoleakage at the hybrid layer, which should contribute to an improvement of long term bonding-dentine clinical performance.

Longitudinal study of the role of salivary proteins on radiation-related caries onset in head and neck cancer patients using 5000 ppm fluoride dentifrice up to one-year post-intensity modulated radiotherapy.

OBJECTIVES: Longitudinal assessment of the role of specific proteins on radiotherapy caries (RC) onset in head and neck cancer patients(HNC) up to one-year post-IMRT using a 5000ppm fluoride paste daily. MATERIALS AND METHODS: Dental status/salivary protein data were obtained from 40 HNC patients pre-IMRT, six months (T1) and 12 months (T2) post-IMRT (ethical approval/consent). DMFT/salivary parameters were quantified, including flow rate, mucin 5B/7, Immunoglobulin A (IgA), cystatin S and α-amylase. RESULTS: 45% patients had at least one carious lesion at T2, a significant reduction in the number of remaining teeth (65% <21), salivary flow rate (< 50%) and, protein secretion (< 0.05) post-IMRT. T1 IgA concentration/secretion rate was associated with RC (p < 0.05). Finally, IgA and total protein concentration obtained at T1 could provide a predictive pattern (AUC 82.3%) for the patients more predisposed to developing RC at T2. CONCLUSIONS: This study demonstrated the significant association of RC with salivary proteins in HNC patients treated with IMRT, revealing the potential role of salivary proteins in the early diagnosis of RC. CLINICAL RELEVANCE: This research contributes to revealing salivary proteins association with RC, and its role in early diagnosis. Therefore, this could be the first step towards personalized medicine approaches to improve this group quality-of-life.

Clinical performance of posterior restorations using a universal adhesive over moist and dry dentin: A 36-month double-blind split-mouth randomized clinical trial.

OBJECTIVES: To evaluate the influence of dentin moisture on the clinical behavior of a universal adhesive on posterior teeth after 36 months of follow-up. METHODS: Forty-five patients participated in this study. Following a split-mouth design, three operators placed 90 Class I/Class II restorations over moist dentin (MD) or dry (DD) (n = 45) with resin composite (Filtek Bulk Fill) and a universal adhesive used in the etch-and-rinse mode (Single Bond Universal). Each restoration was evaluated according to the FDI and USPHS criteria (postoperative sensitivity, fracture and retention, marginal staining, marginal adaptation, and recurrence of caries) at baseline and after 6-, 12-, and 36 months. For statistical analysis, Kruskal Wallis analysis of variance rank (α = 0.05) and Kaplan-Meier survival analysis were used. RESULTS: No significant difference between groups was observed in each FDI criterion after 36 months of clinical evaluation (p > 0.05). The retention rates (confidence interval 95 %) were 97.37 % (86.5 - 99.5) for both MD and DD without significant difference between them (p > 0.05). Eight restorations (MD = 4; DD = 4) showed minimal marginal staining defects (p > 0.05). Two restorations were lost (MD = 1; DD = 1). Fifteen restorations (MD = 8; DD = 7) presented minor marginal discrepancies according to the FDI criteria (p > 0.05). CONCLUSION: The clinical performance of the universal adhesive when applied in etch-and-rinse mode was not influenced by dentin moisture in posterior bulk-fill composite restorations. CLINICAL SIGNIFICANCE: The level of dentin moisture appears not to influence the clinical efficacy of a universal adhesive when applied using the etch-and-rinse technique in posterior composite resin restorations.

Comparison of digitally assessed quality of posterior crown preparations performed with and without previous practice on patient-specific three-dimensional-printed teeth models.

INTRODUCTION: Three-dimensional (3D)-printing technology can provide customizable simulations, but its effects on patient care quality have not been well studied. This study aimed to assess the impact of practicing with patient-specific 3D-printed teeth models on the quality of patients' dental preparations performed by students transitioning to clinical training. Accordingly, the quality of posterior crown preparations was evaluated by objectively analyzing digital scans and grades in two groups: the study group, which practiced beforehand with patient-specific 3D-printed teeth models, and the control group, which did not practice with these models. METHODS: All 78 fourth-year dental students who had just finished their fixed prosthodontics course at the simulation laboratory with training on phantom heads and without previous clinical experience in crown preparations were invited to participate in the study. Sixty-eight agreed to take part and were randomly divided into a study group that practiced crown preparations on 3D-printed models of their own patient's teeth and a control group that did not practice with 3D-printed models and started their clinical work straightforwardly after simulation training. Students completed validated perception questionnaires on self-confidence and clinical skills before and after the protocol, which were compared using a chi-squared test. Crown preparations performed on 3D-printed models and then on patients were digitally scanned and objectively graded by prepCheck software for critical parameters, such as undercuts, taper, and occlusion reduction. Non-parametric tests were used to compare preparations on 3D-printed models and on patients performed by the study group and those on patients made by the control group. RESULTS: Initially, both groups reported similar perceptions of self-confidence and clinical skills levels. The study group significantly improved both aspects after the protocol. Analysis of the scanned preparations demonstrated that the study group removed less tooth structure from actual patients than from the initial 3D-printed models. In contrast, the control group showed excess occlusal clearance in their patients compared to the study group. CONCLUSIONS: Practicing patient-specific 3D-printed teeth before performing procedures clinically appears to enhance preparation quality and minimize unnecessary tooth reduction in early clinical experiences.

NME1 and DCC variants are associated with susceptibility and tumor characteristics in Mexican patients with colorectal cancer.

BACKGROUND: Colorectal cancer (CRC) ranks third in cancer incidence globally and is the second leading cause of cancer-related mortality. The nucleoside diphosphate kinase 1 (NME1) and netrin 1 receptor (DCC) genes have been associated with resistance against tumorigenesis and tumor metastasis. This study investigates the potential association between NME1 (rs34214448 G > T and rs2302254 C > T) and DCC (rs2229080 G > C and rs714 A > G) variants and susceptibility to colorectal cancer development. METHODS: Samples from 232 colorectal cancer patients and 232 healthy blood donors underwent analysis. Variants were identified using polymerase chain reaction-restriction fragment length polymorphism (PCR-RFLP) methodology. Associations were assessed using odds ratios (OR), and the p values were adjusted with Bonferroni test. RESULTS: Individuals carrying the G/T and T/T genotypes for the NME1 rs34214448 variant exhibited a higher susceptibility for develop colorectal cancer (OR = 2.68, 95% CI: 1.76-4.09, P = 0.001 and OR = 2.47, 95% CI: 1.37-4.47, P = 0.001, respectively). These genotypes showed significant associations in patients over 50 years (OR = 2.87, 95% CI: 1.81-4.54, P = 0.001 and OR = 2.99, 95% CI: 1.54-5.79, P = 0.001 respectively) and with early Tumor-Nodule-Metastasis (TNM) stage (P = 0.001), and tumor location in the rectum (P = 0.001). Furthermore, the DCC rs2229080 variant revealed that carriers of the G/C genotype had an increased risk for develop colorectal cancer (OR = 2.00, 95% CI: 1.28-3.11, P = 0.002) and were associated with age over 50 years, sex, and advanced TNM stages (P = 0.001). CONCLUSIONS: These findings suggest that the NME1 rs34214448 and DCC rs2229080 variants play a significant role in colorectal cancer development.

Clinical evaluation of posterior restorations over wet and dry dentin using an etch-and-rinse adhesive: A 36-month randomized clinical trial.

OBJECTIVES: To evaluate the clinical performance of posterior restorations over wet and dry dentin with an etch-and-rinse adhesive after 36 months of clinical service. METHODS: Forty-five participants were recruited, each one had at least two posterior teeth that needed restoration. Ninety restorations were placed on Class I or Class II cavities. For the restoration protocol, a simplified etch-and-rinse adhesive (Adper Single Bond 2) was applied over wet (WD) or dry dentin (DD) and later restored with a bulk-fill composite (Filtek Bulk Fill) under rubber dam isolation. Each restoration was evaluated using the World Dental Federation (FDI) criteria after 6, 12, and 36 months of clinical service, regarding the following principal restoration characteristics: postoperative sensitivity, marginal discoloration, marginal adaptation, fracture of material and retention, and recurrence of caries. Kruskal Wallis analysis of variance rank (α = 0.05) and Kaplan-Meier survival analysis were used for statistical analysis. RESULTS: After 36 months of clinical evaluation, no significant difference between groups was observed in each FDI criterion (p > 0.05). Twenty restorations (WD=10, DD=10) showed minor marginal staining, and twenty-two restorations (WD=11, DD=11) presented small marginal adaptation defects (p > 0.05). Four restorations were lost (WD = 2, DD = 2) and the fracture rates (95% confidence interval) were 94.9% for each one, without significant difference between wet and dry dentin (p > 0.05). SIGNIFICANCE: The degree of dentin moisture does not seem to affect the clinical performance of a simplified etch-and-rinse adhesive in posterior restorations when the adhesive is applied vigorously over the dentine surface.

Prolonged polymerization of a universal adhesive in non-carious cervical lesions: 36-month double-blind randomized clinical trial.

OBJECTIVE: To evaluate the effect of prolonged (P) polymerization time of a universal adhesive system applied in etch-and-rinse (ER) or self-etch (SE) strategies on the clinical performance of restorations in non-carious cervical lesions (NCCLs), after 36 months of clinical service. METHODS: A total of 140 restorations were randomly placed in 35 subjects according to the polymerization time groups: ER (10 s); ER-P (40 s); SE (10 s); and SE-P (40 s) at 1,200 mW/cm2. Composite resin was placed incrementally. The restorations were evaluated immediately and after 6, 12, 18, and 36 months using the FDI criteria. Data were analyzed using the Kaplan-Meier survival test for retention loss, and the Kruskal-Wallis' test for secondary outcomes (α = 0.05). RESULTS: After 36 months, 19 restorations were lost: ER 6, ER-P 2, SE 9, SE-P 2. The retention rates were 82.3% for ER; 94.1 % for ER-P; 73.5 % for SE; and 94.1 % for SE-P, with a significant difference between ER vs. ER-P and SE vs. SE-P, as well as ER vs. SE-P and ER-P vs. SE (p < 0.0001). Minor defects were observed in 18 restorations for the marginal staining criteria: ER 5, ER-P 2, SE 8, SE-P 3; and in 33 restorations for the marginal adaptation criteria: ER 11, ER-P 4, SE 12, and SE-P 6 (p > 0.05). No restorations showed recurrence of caries or postoperative sensitivity. CONCLUSIONS: A prolonged polymerization time of 40 s improves the clinical performance of the universal adhesive for both adhesive strategies evaluated, even after 36 months. CLINICAL SIGNIFICANCE: Prolonging the polymerization time of a universal adhesive from 10 to 40 s has been shown to improve its clinical performance when used in NCCLs.

Protocol to Induce the Temporary Opening of the Blood-Brain Barrier with Short-Time Focused Ultrasound in Rats.

Brain neurodegenerative diseases are central nervous system (CNS) affections typically common in older adults. A new therapeutic approach for them consists of providing specific drugs to the CNS through blood circulation; however, the Blood-Brain Barrier (BBB) prevents almost 100% of neurotherapeutics from reaching the brain. There are indications that Focused Ultrasound (FUS), temporarily placed in the BBB, can achieve a controlled increase in temperature at its focus, allowing temporary, localized, and reversible opening of this barrier, which facilitates the temporary delivery of specific drugs. This work presents a FUS-based protocol for the local, temporary, and reversible opening of the BBB in Wistar rats. The proposed protocol specifies certain power, treatment times, and duty cycle to controllably increase the temperature at the region of interest, i.e., the substantia nigra. Numerical simulations using commercial software based on the finite element method were carried out to determine the optimal size of the craniotomies for nearly full-acoustic transmission. Experiments in rats were performed with the parameters used during computational simulations to determine the adequate opening of the BBB. For this, craniotomies of different sizes were made at coordinates of the substantia nigra, and FUS was applied from the exterior. The opening of the BBB was evaluated using Evans Blue (EB) as an indicator of the crossing of the dye from the blood vessels to brain tissue. Numerical simulations demonstrated a major distance reached by the ultrasound focus with a bigger diameter. Experimental results show the local, temporary, and reversible opening of the BBB through a 10 mm diameter craniotomy, which effectively allowed placing the ultrasound focus over the substantia nigra, unlike a 6 mm diameter craniotomy in which there is a deviation of the focus through that window. Moreover, from these results, it was also determined that the disruption of the BBB was reversible, with an opening duration of 6 h after FUS application. The experimental work developed in this study resulted in a minimally invasive method for the temporary opening of the BBB.

Effect of upper lip compression on pain reduction during local anesthesia. A split-mouth randomized clinical trial

Objectives: To evaluate the effect of pressure on the skin of upper lip in decreasing pain perception during a local maxillary anesthetic injection. Material and Methods: A split-mouth crossover randomized clinical trial was designed. Seventy-one volunteer students (23.6±1.9 years old, 53.5% women) were selected. A group chosen at random had their left or right side of upper lip compressed by a wooden clothes peg as the compression instrument and 0.6 ml of lidocaine 2% with epinephrine 1:100,000 was administered at the buccal apex level of the lateral incisors tooth. Two weeks later anesthesia was administered on the opposite side of the lip according to the randomization recorded. The intensity of perceived pain level between the two injections using a 100 mm visual analog scale (VAS) and co-variable effect were compared (Wilcoxon test p < 0.05, RStudio). Results: The average of the perceived pain with and without upper lip compression was 27.6±14.5 mm (range 0-80 mm) and 36.33±17.9 mm (range 10-90 mm) respectively (p= 0.002). No significant differences were recorded according the covariance analysis with the sex (p = 0.55) and age (p = 0.89). Conclusion: The upper lip compression significantly reduces the perception of pain during a local maxillary anesthetic technique.

5-year clinical performance of posterior bulk-filled resin composite restorations: A double-blind randomized controlled trial.

OBJECTIVES: The aim of this double-blind, and randomized controlled clinical trial was to evaluate the 5-year clinical performance of posterior resin composite restorations placed with the incremental filling technique [IF] or the bulk-fill technique [BF]. Two different adhesive systems were used: etch-&-rinse (ER) or self-etch (SE). METHODS: Posterior dental teeth of 72 participants (n = 236), with a cavity depth of at least 3 mm, were randomly divided into four groups. Restorations were applied with either Tetric N-Bond or Tetric N-Bond SE. The composite resin Tetric N-Ceram Bulk-Fill was placed either with IF or BF. Restorations were evaluated using FDI criteria at baseline and after 1, 2, 3, 4, and 5 years. Statistical analysis was performed using the Wilcoxon Signed rank test (a=0.05). RESULTS: Two hundred and four restorations were evaluated after 5 years. Eleven restorations were considered 'failed', ten due to fracture (4 IF and 6 BF) and one due to secondary caries (IF). The annual failure rate was 1.2% for BF and 1% for IF (p = 0.35). When comparing BF and IF, no significant differences were found for any of the parameters evaluated (p > 0.05). Regarding the adhesive systems, 44 and 51 restorations showed minor problems in terms of marginal adaptation and staining, with significantly more marginal discoloration when the self-etch adhesive was used (p = 0.002). SIGNIFICANCE: The bulk-fill restorative technique showed good clinical behavior compared to the incremental filling technique, especially when using an etch-&-rinse adhesive, after 5 years of clinical evaluation.

Functional electrical stimulation therapy controlled by a P300-based brain-computer interface, as a therapeutic alternative for upper limb motor function recovery in chronic post-stroke patients. A non-randomized pilot study.

Introduction: Up to 80% of post-stroke patients present upper-limb motor impairment (ULMI), causing functional limitations in daily activities and loss of independence. UMLI is seldom fully recovered after stroke when using conventional therapeutic approaches. Functional Electrical Stimulation Therapy (FEST) controlled by Brain-Computer Interface (BCI) is an alternative that may induce neuroplastic changes, even in chronic post-stroke patients. The purpose of this work was to evaluate the effects of a P300-based BCI-controlled FEST intervention, for ULMI recovery of chronic post-stroke patients. Methods: A non-randomized pilot study was conducted, including 14 patients divided into 2 groups: BCI-FEST, and Conventional Therapy. Assessments of Upper limb functionality with Action Research Arm Test (ARAT), performance impairment with Fugl-Meyer assessment (FMA), Functional Independence Measure (FIM) and spasticity through Modified Ashworth Scale (MAS) were performed at baseline and after carrying out 20 therapy sessions, and the obtained scores compared using Chi square and Mann-Whitney U statistical tests (𝛼 = 0.05). Results: After training, we found statistically significant differences between groups for FMA (p = 0.012), ARAT (p < 0.001), and FIM (p = 0.025) scales. Discussion: It has been shown that FEST controlled by a P300-based BCI, may be more effective than conventional therapy to improve ULMI after stroke, regardless of chronicity. Conclusion: The results of the proposed BCI-FEST intervention are promising, even for the most chronic post-stroke patients often relegated from novel interventions, whose expected recovery with conventional therapy is very low. It is necessary to carry out a randomized controlled trial in the future with a larger sample of patients.

48-month clinical evaluation of a copper-containing universal adhesive in non-carious cervical lesions: A double-blind randomised clinical trial.

OBJECTIVES: This study aimed to evaluate the effect of copper nanoparticles (CuNp) on the clinical performance of a universal adhesive system used as an etch-and-rinse or self-etch strategy. METHODS: A total of 216 class V (non-carious lesions) restorations were randomly placed in 36 subjects according to the following groups: ERcu, adhesive in etch-and-rinse with 0.1% CuNp; ERct, adhesive in etch-and-rinse without CuNp; SEcu, adhesive in self-etch with 0.1% CuNp; and Sect, adhesive in self-etch without CuNp. Restorations were evaluated at baseline and at 6, 12, 18, 36, and 48 months, using the FDI and USPHS criteria. Appropriate statistical analyses were performed (α = 0.05). RESULTS: After 48 months, 14 restorations were lost (two for ERcu, five for SEcu, and seven for SEct) and the retention rates (95% confidence interval [CI]) were 74.1% for ERcu (95% CI 61.1-83.8); 81.5% for ERct (95% CI 69.2-89.6); 64.8% (95% CI 51.5-76.2) for SEcu; and 64.8% (95% CI 51.5-76.2) for SEct, with statistical differences between SEct vs. ERct and SEcu vs. ERct (p < 0.05). No significant differences between the groups were observed when the secondary parameters were evaluated (p > 0.05). Nineteen restorations (two for ERcu, two for ERct, six for SEcu, and nine for SEct) showed minor marginal staining, and 44 restorations (7 for ERcu, 8 for ERct, 14 for SEcu, and 15 for SEct) presented minimal marginal adaptation defects. SIGNIFICANCE: This is the first long-term clinical trial to show that the addition of CuNp to a universal adhesive system does not affect clinical performance.

Trifocal intraocular lenses versus bifocal intraocular lenses after cataract extraction among participants with presbyopia.

BACKGROUND: Presbyopia occurs when the lens of the eyes loses its elasticity leading to loss of accommodation. The lens may also progress to develop cataract, affecting visual acuity and contrast sensitivity. One option of care for individuals with presbyopia and cataract is the use of multifocal or extended depth of focus intraocular lens (IOL) after cataract surgery. Although trifocal and bifocal IOLs are designed to restore three and two focal points respectively, trifocal lens may be preferable because it restores near, intermediate, and far vision, and may also provide a greater range of useful vision and allow for greater spectacle independence in individuals with presbyopia. OBJECTIVES: To assess the effectiveness and safety of implantation with trifocal versus bifocal IOLs during cataract surgery among people with presbyopia. SEARCH METHODS: We searched the Cochrane Central Register of Controlled Trials (CENTRAL) (which contains the Cochrane Eyes and Vision Trials Register) (2022, Issue 3); Ovid MEDLINE; Embase.com; PubMed; ClinicalTrials.gov; and the World Health Organization (WHO) International Clinical Trials Registry Platform (ICTRP). We did not use any date or language restrictions in the electronic search for trials. We last searched the electronic databases on 31 March 2022.  SELECTION CRITERIA: We included randomized controlled trials that compared trifocal and bifocal IOLs among participants 30 years of age or older with presbyopia undergoing cataract surgery. DATA COLLECTION AND ANALYSIS: We used standard Cochrane methodology and graded the certainty of the body of evidence according to the GRADE classification. MAIN RESULTS: We identified seven studies conducted in Europe and Turkey with a total of 331 participants. All included studies assessed visual acuity using a logarithm of the minimum angle of resolution (LogMAR chart). Of them, six (86%) studies assessed uncorrected distance visual acuity (the primary outcome of this review). Some studies also examined our secondary outcomes including uncorrected near, intermediate, and best-corrected distance visual acuity, as well as contrast sensitivity. Study characteristics All participants had bilateral cataracts with no pre-existing ocular pathologies or ocular surgery. Participants' mean age ranged from 55 to 74 years. Three studies reported on gender of participants, and they were mostly women. We assessed all of the included studies as being at unclear risk of bias for most domains. Two studies received financial support from manufacturers of lenses evaluated in this review, and at least one author of another study reported receiving payments for delivering lectures with lens manufacturers. Findings All studies compared trifocal versus bifocal IOL implantation on visual acuity outcomes measured on a LogMAR scale. At one year, trifocal IOL showed no evidence of effect on uncorrected distance visual acuity (mean difference (MD) 0.00, 95% confidence interval (CI) -0.04 to 0.04; I2 = 0%; 2 studies, 107 participants; low-certainty evidence) and uncorrected near visual acuity (MD 0.01, 95% CI -0.04 to 0.06; I2 = 0%; 2 studies, 107 participants; low-certainty evidence). Trifocal IOL implantation may improve uncorrected intermediate visual acuity at one year (MD -0.16, 95% CI -0.22 to -0.10; I2 = 0%; 2 studies, 107 participants; low-certainty evidence), but showed no evidence of effect on best-corrected distance visual acuity at one year (MD 0.00, 95% CI -0.03 to 0.04; I2 = 0%; 2 studies, 107 participants; low-certainty evidence). No study reported on contrast sensitivity or quality of life at one-year follow-up. Data from one study at three months suggest that contrast sensitivity did not differ between groups under photopic conditions, but may be worse in the trifocal group in one of the four frequencies under mesopic conditions (MD -0.19, 95% CI -0.33 to -0.05; 1 study; I2 = 0%, 25 participants; low-certainty evidence). One study examined vision-related quality of life using the 25-item National Eye Institute Visual Function Questionnaire (NEI-VFQ-25) at six months, and suggested no evidence of a difference between trifocal and bifocal IOLs (MD 1.41, 95% CI -1.78 to 4.60; 1 study, 40 participants; low-certainty evidence). Adverse events Adverse events reporting varied among studies. Of five studies reporting information on adverse events, two studies observed no intraoperative and postoperative complications or no posterior capsular opacification at six months. One study reported that glare and halos were similar to the preoperative measurements. One study reported that 4 (20%) and 10 (50%) participants had glare complaints at 6 months in trifocal and bifocal group, respectively (risk ratio 0.40, 95% CI 0.15 to 1.07; 40 participants). One study reported that four eyes (11.4%) in the bifocal group and three eyes (7.5%) in the trifocal group developed significant posterior capsular opacification requiring YAG capsulotomy at one year. The certainty of the evidence for adverse events was low. AUTHORS' CONCLUSIONS: We found low-certainty of evidence that compared with bifocal IOL, implantation of trifocal IOL may improve uncorrected intermediate visual acuity at one year. However, there was no evidence of a difference between trifocal and bifocal IOL for uncorrected distance visual acuity, uncorrected near visual acuity, and best-corrected visual acuity at one year. Future research should include the comparison of both trifocal IOL and specific bifocal IOLs that correct intermediate visual acuity to evaluate important outcomes such as contrast sensitivity, quality of life, and vision-related adverse effects.

Biodiesel Production Using Lithium Metasilicate Synthesized from Non-Conventional Sources.

A facile and versatile process to produce lithium metasilicate (Li2SiO3) from non-conventional silicon sources (two different sand sources from the central area of México) was developed. The synthesis protocol based on a solid-state reaction followed by a hydrothermal treatment resulted in highly pure lithium metasilicate, as corroborated by XRD, SEM-EDS, and XPS analysis. Furthermore, lithium metasilicate was used as a heterogeneous catalyst for biodiesel production from soybean oil, where conversion yields were compared according to the silicon source used (based on chemical purity, stability, and yield efficiency). The best performing metasilicate material displayed a maximum of 95.5% of biodiesel conversion under the following conditions: 180 min, 60 °C, 5% catalyst (wt./wt., catalyst-to-oil), and 18:1 (methanol:oil). This contribution opens up alternatives for the production of lithium metasilicate using non-conventional precursors and its use as an alternative catalyst in biodiesel production, displaying better chemical stability against humidity than conventional heterogeneous catalysts.

Devices and Technology in Transcranial Magnetic Stimulation: A Systematic Review.

The technology for transcranial magnetic stimulation (TMS) has significantly changed over the years, with important improvements in the signal generators, the coils, the positioning systems, and the software for modeling, optimization, and therapy planning. In this systematic literature review (SLR), the evolution of each component of TMS technology is presented and analyzed to assess the limitations to overcome. This SLR was carried out following the PRISMA 2020 statement. Published articles of TMS were searched for in four databases (Web of Science, PubMed, Scopus, IEEE). Conference papers and other reviews were excluded. Records were filtered using terms about TMS technology with a semi-automatic software; articles that did not present new technology developments were excluded manually. After this screening, 101 records were included, with 19 articles proposing new stimulator designs (18.8%), 46 presenting or adapting coils (45.5%), 18 proposing systems for coil placement (17.8%), and 43 implementing algorithms for coil optimization (42.6%). The articles were blindly classified by the authors to reduce the risk of bias. However, our results could have been influenced by our research interests, which would affect conclusions for applications in psychiatric and neurological diseases. Our analysis indicates that more emphasis should be placed on optimizing the current technology with a special focus on the experimental validation of models. With this review, we expect to establish the base for future TMS technological developments.

Students' and tutors' perceptions of a deliberate simulated practice using patient-specific virtual and three-dimensional printed teeth models: A pilot study.

OBJECTIVE: This pilot study aimed to investigate the perceptions of dental students and their tutors of a deliberate simulated practice using patient-specific virtual and three-dimensional (3D) printed teeth models. This is before they perform their first indirect posterior tooth restoration on their patients. METHODS: Seventy-eight fourth-year dental students from the 2021 Comprehensive Clinic I course at the University of the Andes, Chile, were invited to participate in a deliberate practice protocol. This consisted of digitally scanning their patients' teeth, printing the files three-dimensionally, and loading them into a virtual reality (VR) dental simulator to create patient-specific models. Subsequently, they practiced the same indirect posterior restorations on these models before performing them on their actual patients. Perceptions about students' preparedness to perform tooth preparations before and after the protocol were collected from students and their tutors through surveys. RESULTS: Sixty-three students (43 female) and six clinical tutors (all male) participated in the study. Before practicing with their patient-specific models, most students believed they had the knowledge, practical skills, and self-confidence to perform indirect restorations on their patients. However, after the protocol, most students thought their self-confidence increased and felt better prepared to treat their patients. Most students preferred the 3D-printed models over the VR models to practice but mentioned that it did not feel like drilling dental enamel. Tutors believed that participating students had higher self-confidence when treating their patients and were more autonomous. CONCLUSIONS: This study demonstrated that students and clinical tutors had positive perceptions of practicing with patient-specific virtual and 3D-printed teeth models before students performed their first indirect restorations on their patients.

Is the use of a potassium nitrate dentifrice effective in reducing tooth sensitivity related to in-office bleaching? A randomized triple-blind clinical trial.

OBJECTIVE: The aims of this study were to evaluate whether the use of a dentifrice containing 5% potassium nitrate (KNO3 ) prior to and during in-office dental bleaching reduces bleaching-induced tooth sensitivity and affects bleaching efficiency. MATERIALS AND METHODS: Thirty-eight individuals were randomly distributed into two groups (n = 19). The experimental group performed toothbrushing using a dentifrice containing 5% KNO3 , one week before treatment and before the first and second bleaching sessions. In the control group, a placebo dentifrice without KNO3 was applied as described for the first group. Tooth sensitivity was recorded on visual analog scales (VAS) and numeric rating scales (NRS) immediately and up to 48 h after bleaching sessions. Color change at different time intervals, was evaluated with shade guide units (∆SGU) and a digital spectrophotometer (∆E CIELab 1976 and CIEDE2000) at baseline and 7, 15, and 30 days post-bleaching. Mann-Whitney test and t-test were used to evaluate TS intensity for NRS and VAS scales, respectively, and T-test was used for color difference evaluation. RESULTS: No significant difference in tooth sensitivity's absolute risk and intensity were observed between tested groups in any evaluated treatment time for NRS (p = 0.91) or VAS scales (p = 0.48). T-test showed no significant difference in both ∆E and ∆SGU tooth color among the experimental and control groups during the different evaluation times (p = 0.27). CONCLUSION: The use of a dentifrice containing 5% KNO3 does not prevent post-operatory tooth sensitivity but allows the same whitening efficiency as a regular dentifrice. CLINICAL SIGNIFICANCE: The use of a dentifrice-containing KNO3 did not prevent bleaching-induced tooth sensitivity when high-concentrated hydrogen peroxide was used for in-office bleaching.

Effect of laterotrusive occlusal scheme on chewing duration, external intercostal muscular activity, heart rate, and oxygen saturation.

Objective: To evaluate the effect of the laterotrusive occlusal scheme on chewing duration, external intercostal (EIC) electromyographic (EMG) activity, heart rate (HR), and oxygen saturation (OS) during different tasks in the upright seated position.Methods: Fifty young participants, 25 with canine guidance and 25 with group function, were included. Chewing duration, bilateral EIC EMG activity, HR, and OS were recorded during the following tasks: 1) chewing until swallowing threshold; 2) laterotrusive teeth grinding.Results: Chewing duration, bilateral EIC EMG activity, HR, and OS showed no significant differences between the two laterotrusive occlusal schemes during the tasks studied.Conclusion: These results suggest that chewing duration, EIC muscle activity, HR, and OS were not significantly influenced by the laterotrusive occlusal scheme. Therefore, when a modification of the laterotrusive occlusal scheme is needed during oral rehabilitation or orthodontic treatment, canine guidance or group function should not significantly change EMG activity of EIC muscles.

Do subjects with forced lip closure have different perioral and jaw muscles activity?

Objective: To evaluate the activity of mentalis (MN), buccinator (BC), and suprahyoid (SH) muscles among participants with different lip competence..Methods: Sixty-three participants were classified clinically and assigned to the following groups of 21 each: 1) competent lips (competent), 2) incompetent lips (incompetent), or 3) forced lip closure (forced). Activity was recorded at rest, swallowing, speaking, reciprocal compression of the lips, and chewing.Results: MN activity in incompetent was significantly higher than competent at rest, and it was significantly higher in incompetent and forced when compared with competent during swallowing (p< .05). No differences among incompetent and forced were observed (p> .05). During speaking, reciprocal compression of the lips, and chewing, MN activity did not show significant differences among groups. BC and SH activity did not show significant differences (p> .05).Conclusion: MN activity during swallowing can be considered a relevant biomarker to differentiate between forced and competent participants.