ABSTRACT
Microfluidic flow reactors functionalized with immobilized human liver microsomes (HLM chips) represent a powerful tool for drug discovery and development by enabling mechanism-based enzyme inhibition studies under flow-through conditions. Additionally, HLM chips may be exploited in streamlined production of human drug metabolites for subsequent microfluidic in vitro organ models or as metabolite standards for drug safety assessment. However, the limited shelf life of the biofunctionalized microreactors generally poses a major barrier to their commercial adaptation in terms of both storage and shipping. The shelf life of the HLM chips in the wetted state is ca. 2-3 weeks only and requires cold storage at 4 °C. In this study, we developed a freeze-drying method for lyophilization of HLMs that are readily immobilized inside microfluidic pillar arrays made from off-stoichiometric thiol-ene polymer. The success of lyophilization was evaluated by monitoring the cytochrome P450 and UDP-glucuronosyltransferase enzyme activities of rehydrated HLMs for several months post-freeze-drying. By adapting the freeze-drying protocol, the HLM chips could be stored at room temperature (protected from light and moisture) for at least 9 months (n = 2 independent batches) and up to 16 months at best, with recovered enzyme activities within 60-120% of the non-freeze-dried control chips. This is a major improvement over the cold-storage requirement and the limited shelf life of the non-freeze-dried HLM chips, which can significantly ease the design of experiments, decrease energy consumption during storage, and reduce the shipping costs with a view to commercial adaptation.
Subject(s)
Freeze Drying , Microsomes, Liver , Humans , Microsomes, Liver/metabolism , Microsomes, Liver/chemistry , Cytochrome P-450 Enzyme System/metabolism , Sulfhydryl Compounds/chemistry , Sulfhydryl Compounds/metabolism , Microfluidic Analytical Techniques/instrumentationABSTRACT
To study and then harness the tumor-specific T cell dynamics after allogeneic hematopoietic stem cell transplant, we typed the frequency, phenotype, and function of lymphocytes directed against tumor-associated antigens (TAAs) in 39 consecutive transplanted patients, for 1 year after transplant. We showed that TAA-specific T cells circulated in 90% of patients but display a limited effector function associated to an exhaustion phenotype, particularly in the subgroup of patients deemed to relapse, where exhausted stem cell memory T cells accumulated. Accordingly, cancer-specific cytolytic functions were relevant only when the TAA-specific T cell receptors (TCRs) were transferred into healthy, genome-edited T cells. We then exploited trogocytosis and ligandome-on-chip technology to unveil the specificities of tumor-specific TCRs retrieved from the exhausted T cell pool. Overall, we showed that harnessing circulating TAA-specific and exhausted T cells allow to isolate TCRs against TAAs and previously not described acute myeloid leukemia antigens, potentially relevant for T cell-based cancer immunotherapy.
Subject(s)
Leukemia, Myeloid, Acute , T-Cell Exhaustion , Humans , Trogocytosis , Receptors, Antigen, T-Cell/genetics , T-Lymphocytes , Antigens, Neoplasm , Leukemia, Myeloid, Acute/therapyABSTRACT
Identification of HLA class I ligands from the tumor surface (ligandome or immunopeptidome) is essential for designing T-cell mediated cancer therapeutic approaches. However, the sensitivity of the process for isolating MHC-I restricted tumor-specific peptides has been the major limiting factor for reliable tumor antigen characterization, making clear the need for technical improvement. Here, we describe our work from the fabrication and development of a microfluidic-based chip (PeptiCHIP) and its use to identify and characterize tumor-specific ligands on clinically relevant human samples. Specifically, we assessed the potential of immobilizing a pan-HLA antibody on solid surfaces via well-characterized streptavidin-biotin chemistry, overcoming the limitations of the cross-linking chemistry used to prepare the affinity matrix with the desired antibodies in the immunopeptidomics workflow. Furthermore, to address the restrictions related to the handling and the limited availability of tumor samples, we further developed the concept toward the implementation of a microfluidic through-flow system. Thus, the biotinylated pan-HLA antibody was immobilized on streptavidin-functionalized surfaces, and immune-affinity purification (IP) was carried out on customized microfluidic pillar arrays made of thiol-ene polymer. Compared to the standard methods reported in the field, our methodology reduces the amount of antibody and the time required for peptide isolation. In this work, we carefully examined the specificity and robustness of our customized technology for immunopeptidomics workflows. We tested this platform by immunopurifying HLA-I complexes from 1 × 106 cells both in a widely studied B-cell line and in patients-derived ex vivo cell cultures, instead of 5 × 108 cells as required in the current technology. After the final elution in mild acid, HLA-I-presented peptides were identified by tandem mass spectrometry and further investigated by in vitro methods. These results highlight the potential to exploit microfluidics-based strategies in immunopeptidomics platforms and in personalized immunopeptidome analysis from cells isolated from individual tumor biopsies to design tailored cancer therapeutic vaccines. Moreover, the possibility to integrate multiple identical units on a single chip further improves the throughput and multiplexing of these assays with a view to clinical needs.
Subject(s)
Histocompatibility Antigens Class I , Microfluidics , Antigens, Neoplasm , Humans , Ligands , PeptidesABSTRACT
The superfamily of hepatic cytochrome P450 (CYP) enzymes is responsible for the intrinsic clearance of the majority of therapeutic drugs in humans. However, the kinetics of drug clearance via CYPs varies significantly among individuals due to both genetic and external factors, and the enzyme amount and function are also largely impacted by many liver diseases. In this study, we developed a new methodology, based on digital microfluidics (DMF), for rapid determination of individual alterations in CYP activity from human-derived liver samples in biopsy-scale. The assay employs human liver microsomes (HLMs), immobilized on magnetic beads to facilitate determination of the activity of microsomal CYP enzymes in a parallelized system at physiological temperature. The thermal control is achieved with the help of a custom-designed, inkjet-printed microheater array modularly integrated with the DMF platform. The CYP activities are determined with the help of prefluorescent, enzyme-selective model compounds by quantifying the respective fluorescent metabolites based on optical readout in situ. The selectivity and sensitivity of the assay was established for four different CYP model reactions, and the diagnostic concept was validated by determining the interindividual variation in one of the four model reaction activities, that is, ethoxyresorufin O-deethylation (CYP1A1/2), between five donors. Overall, the developed protocol consumes only about 15 µg microsomal protein per assay. It is thus technically adaptable to screening of individual differences in CYP enzyme function from biopsy-scale liver samples in an automated fashion, so as to support tailoring of medical therapies, for example, in the context of liver disease diagnosis.
Subject(s)
Cytochrome P-450 Enzyme System/metabolism , Enzyme Assays/instrumentation , Lab-On-A-Chip Devices , Liver/enzymology , Cytochrome P-450 Enzyme System/chemistry , Enzymes, Immobilized/chemistry , Enzymes, Immobilized/metabolism , Equipment Design , HumansABSTRACT
Three-dimensional (3D) printing has recently emerged as a cost-effective alternative for rapid prototyping of microfluidic devices. The feature resolution of stereolithography-based 3D printing is particularly well suited for manufacturing of continuous flow cell culture platforms. Poor cell adhesion or material-induced cell death may, however, limit the introduction of new materials to microfluidic cell culture. In this work, we characterized four commercially available materials commonly used in stereolithography-based 3D printing with respect to long-term (2 month) cell survival on native 3D printed surfaces. Cell proliferation rates, along with material-induced effects on apoptosis and cell survival, were examined in mouse embryonic fibroblasts. Additionally, the feasibility of Dental SG (material with the most favored properties) for culturing of human hepatocytes and human-induced pluripotent stem cells was evaluated. The strength of cell adhesion to Dental SG was further examined over a shear force gradient of 1-89 dyne per cm2 by using a custom-designed microfluidic shear force assay incorporating a 3D printed, tilted and tapered microchannel sealed with a polydimethylsiloxane lid. According to our results, autoclavation of the devices prior to cell seeding played the most important role in facilitating long-term cell survival on the native 3D printed surfaces with the shear force threshold in the range of 3-8 dyne per cm2.
Subject(s)
Lab-On-A-Chip Devices , Stereolithography , Animals , Cell Adhesion , Cell Proliferation , Fibroblasts , Mice , Printing, Three-DimensionalABSTRACT
We have identified the most likely reaction mechanism for oxidizing heptafulvenes to the corresponding tropones by experimental and theoretical investigations. The experimental studies were done by coupling a three-dimensional printed miniaturized reactor with an integrated electrospray ionization needle to a mass spectrometer. Using the experimentally observed ions as a basis, nine alternative reaction pathways were investigated with density functional theory calculations. The lowest energy reaction pathway starts with the formation of an epoxide that is opened upon the addition of a second equivalent of the oxidizing species meta-chloroperoxybenzoic acid. The adduct formed then undergoes a Criegee-like rearrangement to yield a positively charged hemiketal, which on deprotonation dissociates into acetone and tropone. Overall, the reaction mechanism resembles a Hock-like rearrangement.
ABSTRACT
A simple flow chemistry microreactor with an electrospray ionization tip for real time mass spectrometric reaction monitoring is introduced. The microreactor was fabricated by a laser-based additive manufacturing technique from acid-resistant stainless steel 316L. The functionality of the microreactor was investigated by using an inverse electron demand Diels-Alder and subsequent retro Diels-Alder reaction for testing. Challenges and problems encountered are discussed and improvements proposed. Adsorption of reagents to the rough stainless steel channel walls, short length of the reaction channel, and making a proper ESI tip present challenges, but the microreactor is potentially useful as a disposable device.
ABSTRACT
A new heated capillary photoionization (CPI) ion source design was developed to photoionize analytes inside a transfer capillary between a gas chromatograph (GC) and a mass spectrometer (MS). The CPI setup included a wide, oval-shaped vacuum-ultraviolet (VUV) transparent magnesium fluoride (MgF2) window to maximize photoionization efficiency and thus sensitivity. The source contained a nitrogen housing around the ionization chamber inlet to avoid undesirable hydrolysis and oxidation reactions with ambient air and to maximize the proportion of formed molecular radical cations of analytes. The feasibility of the ion source was studied by analyzing 18 endogenous steroids in urine as their trimethylsilyl (TMS) derivatives with gas chromatography-tandem mass spectrometry (GC-MS/MS). The method was validated and applied to human urine samples. To our best knowledge, this is the first time that a capillary photoionization ion source has been applied for quantitative analysis of biological samples. The GC-CPI-MS/MS method showed good chromatographic resolution (peak half-widths between 3.1 to 5.3 s), acceptable linearity (coefficient of determination between 0.981 to 0.996), and repeatability (relative standard deviation (RSD%) between 5 to 18%). Limits of detection (LOD) were between 2 to 100 pg mL-1 and limits of quantitation (LOQ) were between 0.05 to 2 ng mL-1. In total, 15 steroids were quantified either as a free steroid or glucuronide conjugate from the urine of volunteers. The new CPI source design showed excellent sensitivity for analysis of steroids in complex biological samples.
Subject(s)
Gas Chromatography-Mass Spectrometry , Steroids/urine , Urinalysis/methods , Humans , Limit of Detection , Reproducibility of Results , Tandem Mass SpectrometryABSTRACT
This is the first report on capillary photoionization (CPI) interfacing a liquid chromatograph (LC) and mass spectrometer (MS). A new heated CPI ion source was developed, including a heated transfer capillary, a wide oval-shaped and low-depth ionization chamber with a vacuum ultraviolet (VUV) transparent magnesium fluoride (MgF2) window to increase the photoionization efficiency and thus the sensitivity. As both analytes and eluent are first vaporized and then photoionized inside the CPI ion source between the atmosphere and the vacuum of MS, the ion transfer efficiency into the MS and thus the sensitivity is improved. The effect of the most important operation parameters, the eluent flow rate and temperature of the CPI source, on the signal intensity was studied with selected steroids. The feasibility of LC-CPI-MS/MS for the quantitative analysis of steroids was also studied in terms of linearity, repeatability, and limits of detection. The method showed good quantitative performance and sensitivity down to the low femto-mole level.
ABSTRACT
This work describes the interfacing of electrowetting-on-dielectric based digital microfluidic (DMF) sample preparation devices with ambient mass spectrometry (MS) via desorption atmospheric pressure photoionization (DAPPI). The DMF droplet manipulation technique was adopted to facilitate drug distribution and metabolism assays in droplet scale, while ambient mass spectrometry (MS) was exploited for the analysis of dried samples directly on the surface of the DMF device. Although ambient MS is well-established for bio- and forensic analyses directly on surfaces, its interfacing with DMF is scarce and requires careful optimization of the surface-sensitive processes, such as sample precipitation and the subsequent desorption/ionization. These technical challenges were addressed and resolved in this study by making use of the high mechanical, thermal, and chemical stability of SU-8. In our assay design, SU-8 served as the dielectric layer for DMF as well as the substrate material for DAPPI-MS. The feasibility of SU-8 based DMF devices for DAPPI-MS was demonstrated in the analysis of selected pharmaceuticals following on-chip liquid-liquid extraction or an enzymatic dealkylation reaction. The lower limits of detection were in the range of 1â»10 pmol per droplet (0.25â»1.0 µg/mL) for all pharmaceuticals tested.
ABSTRACT
We report the development and characterization of digital microfluidic (DMF) immobilized enzyme reactors (IMERs) for studying cytochrome P450 (CYP)-mediated drug metabolism on droplet scale. The on-chip IMERs consist of porous polymer (thiol-ene) monolith plugs prepared in situ by photopolymerization and functionalized with recombinant CYP1A1 isoforms (an important detoxification route for many drugs and other xenobiotics). The DMF devices also incorporate inexpensive, inkjet-printed microheaters for on-demand regio-specific heating of the IMERs to physiological temperature, which is crucial for maintaining the activity of the temperature-sensitive CYP reaction. For on-chip monitoring of the CYP activity, the DMF devices were combined with a commercial well-plate reader, and a custom fluorescence quantification method was developed for detection of the chosen CYP1A1 model activity (ethoxyresorufin-O-deethylation). The reproducibility of the developed assay was examined with the help of ten parallel CYP-IMERs. All CYP-IMERs provided statistically significant difference (in fluorescence response) compared to any of the negative controls (including room-temperature reactions). The average (n = 10) turnover rate was 20.3 ± 9.0 fmol resorufin per minute. Via parallelization, the concept of the droplet-based CYP-IMER developed in this study provides a viable approach to rapid and low-cost prediction of the metabolic clearance of new chemical entities in vitro.
Subject(s)
Cytochrome P-450 Enzyme System/chemistry , Lab-On-A-Chip Devices , Microfluidics , Printing , Reproducibility of ResultsABSTRACT
In mass spectrometry imaging of tissues, the size of structures that can be distinguished is determined by the spatial resolution of the imaging technique. Here, the spatial resolution of IR laser ablation is markedly improved by increasing the distance between the laser and the focusing lens. As the distance between the laser and the lens is increased from 1 to 18 m, the ablation spot size decreases from 440 to 44 µm. This way, only the collimated center of the divergent laser beam is directed on the focusing lens, which results in better focusing of the beam. Part of the laser energy is lost at longer distance, but this is compensated by focusing of the radiation to a smaller area on the sample surface. The long distance can also be achieved by a set of mirrors, between which the radiation travels before it is directed to the focusing lens and the sample. This method for improving the spatial resolution can be utilized in mass spectrometry imaging of tissues by techniques that utilize IR laser ablation, such as laser ablation electrospray ionization, laser ablation atmospheric pressure photoionization, and matrix-assisted laser desorption electrospray ionization. Graphical Abstract á .
ABSTRACT
Desorption atmospheric pressure photoionization (DAPPI) allows surface analysis in the open atmosphere and is thus an appropriate method for the direct coupling of thin-layer chromatography (TLC) and mass spectrometry (MS). Here, the capability of DAPPI-MS for ionizing and detecting lipids, namely, cholesterol, triacylglycerols, 1,2-diol diesters, wax esters, cholesteryl esters, and hydrocarbons, from TLC and high-performance thin-layer chromatography (HPTLC) plates in MS and MS2 modes was tested. Limits of detection for lipid standards separated using normal-phase (NP)-TLC and NP-HPTLC were established. TLC/DAPPI-MS was applied for lipids of vernix caseosa, a white creamy proteolipid biofilm that progressively coats the fetus during the last trimester of the pregnancy, and plant oils including caraway, parsley, safflower, and jojoba oils. Various lipids were identified by means of high resolution/accurate mass measurement of Orbitrap and comparison of the retardation factors with standards. Lipid class separation was carried out on the NP-HPTLC plates, whereas individual triacylglycerol and wax ester species were separated on the reversed-phase HPTLC plates. DAPPI-MS was found to be a simple, rapid, and efficient approach for detecting lipids separated by TLC.
ABSTRACT
RATIONALE: Neonicotinoids are widely used insecticides which have been shown to affect the memory and learning abilities of honey bees, and are suspected to play a part in the unexplainable, large-scale loss of honey bee colonies. Fast methods, such as ambient mass spectrometry (MS), for their analysis from a variety of matrices are necessary to control the use of forbidden products and study the spreading of insecticides in nature. METHODS: The feasibilities of two ambient MS methods, desorption electrospray ionization (DESI) and desorption atmospheric pressure photoionization (DAPPI), for the analysis of five most used neonicotinoid compounds, thiacloprid, acetamiprid, clothianidin, imidacloprid and thiamethoxam, were tested. In addition, DAPPI was used to analyze fresh rose leaves treated with commercially available thiacloprid insecticide and dried and powdered turnip rape flowers, which had been collected from a field treated with thiacloprid-containing insecticide. RESULTS: DAPPI was found to be more sensitive than DESI, with 2-11 times better signal-to-noise ratios, and limits of detection at 0.4-5.0 fmol for the standard compounds. DAPPI was able to detect thiacloprid from the rose leaves even 2.5 months after the treatment and from the turnip rape flower samples collected from a field. The analysis of plant material by DAPPI did not require extraction or other sample preparation. CONCLUSIONS: DAPPI was found to be suitable for the fast and direct qualitative analysis of thiacloprid neonicotinoid from plant samples. It shows promise as a fast tool for screening of forbidden insecticides, or studying the distribution of insecticides in nature.
Subject(s)
Flowers/chemistry , Insecticides/analysis , Plant Leaves/chemistry , Pyridines/analysis , Spectrometry, Mass, Electrospray Ionization/methods , Sulfur Compounds/analysis , Brassica napus/chemistry , Limit of Detection , Rosa/chemistryABSTRACT
Many insects use chemicals synthesized in exocrine glands and stored in reservoirs to protect themselves. Two chemically defended insects were used as models for the development of a new rapid analytical method based on desorption atmospheric pressure photoionization-mass spectrometry (DAPPI-MS). The distribution of defensive chemicals on the insect body surface was studied. Since these chemicals are predominantly nonpolar, DAPPI was a suitable analytical method. Repeatability of DAPPI-MS signals and effects related to non-planarity and roughness of samples were investigated using acrylic sheets uniformly covered with an analyte. After that, analytical figures of merit of the technique were determined. The spatial distribution of (E)-1-nitropentadec-1-ene, a toxic nitro compound synthesized by soldiers of the termite Prorhinotermes simplex, was investigated. Then, the spatial distribution of the unsaturated aldehydes (E)-hex-2-enal, (E)-4-oxohex-2-enal, (E)-oct-2-enal, (E,E)-deca-2,4-dienal and (E)-dec-2-enal was monitored in the stink bug Graphosoma lineatum. Chemicals present on the body surface were scanned along the median line of the insect from the head to the abdomen and vice versa, employing either the MS or MS(2) mode. In this fast and simple way, the opening of the frontal gland on the frons of termite soldiers and the position of the frontal gland reservoir, extending deep into the abdominal cavity, were localized. In the stink bug, the opening of the metathoracic scent glands (ostiole) on the ventral side of the thorax as well as the gland reservoir in the median position under the ventral surface of the anterior abdomen were detected and localized. The developed method has future prospects in routine laboratory use in life sciences.
Subject(s)
Aldehydes/analysis , Heteroptera/chemistry , Isoptera/chemistry , Mass Spectrometry/instrumentation , Nitro Compounds/analysis , Animals , Atmospheric Pressure , Equipment Design , Heteroptera/anatomy & histology , Isoptera/anatomy & histologyABSTRACT
A new ambient mass spectrometry method, solvent jet desorption capillary photoionization (DCPI), is described. The method uses a solvent jet generated by a coaxial nebulizer operated at ambient conditions with nitrogen as nebulizer gas. The solvent jet is directed onto a sample surface, from which analytes are extracted into the solvent and ejected from the surface in secondary droplets formed in collisions between the jet and the sample surface. The secondary droplets are directed into the heated capillary photoionization (CPI) device, where the droplets are vaporized and the gaseous analytes are ionized by 10 eV photons generated by a vacuum ultraviolet (VUV) krypton discharge lamp. As the CPI device is directly connected to the extended capillary inlet of the MS, high ion transfer efficiency to the vacuum of MS is achieved. The solvent jet DCPI provides several advantages: high sensitivity for nonpolar and polar compounds with limit of detection down to low fmol levels, capability of analyzing small and large molecules, and good spatial resolution (250 µm). Two ionization mechanisms are involved in DCPI: atmospheric pressure photoionization, capable of ionizing polar and nonpolar compounds, and solvent assisted inlet ionization capable of ionizing larger molecules like peptides. The feasibility of DCPI was successfully tested in the analysis of polar and nonpolar compounds in sage leaves and chili pepper.
Subject(s)
Mass Spectrometry/methods , Solvents/chemistry , Capsicum/chemistry , Feasibility Studies , Mass Spectrometry/instrumentation , Nebulizers and Vaporizers , Salvia officinalis/chemistry , VolatilizationABSTRACT
The capability of employing synthesized zwitterionic silica-based monolithic capillary columns (140 mm × 0.1mm) for separation of highly polar and hydrophilic nucleobases, nucleosides, and nucleotides in hydrophilic interaction chromatography is reported. The suitability of the columns for on-line conjunction with electrospray tandem mass spectrometry was explored. Our results show that the grafted layer of zwitterionic monomer ([2-(methacryloyloxy)ethyl]-dimethyl-(3-sulfopropyl)-ammonium hydroxide or 2-methacryloyloxyethyl phosphorylcholine) on the silica monolithic surface significantly improved the separation selectivity and reproducibility, as compared to the bare silica monolith. The stepwise elution from 90% to 70% of acetonitrile enabled separation of a complex sample mixture containing 21 compounds with a total analysis time less than 40 min.
Subject(s)
Nucleosides/isolation & purification , Nucleotides/isolation & purification , Spectrometry, Mass, Electrospray Ionization/methods , Tandem Mass Spectrometry/methods , Chromatography, High Pressure Liquid/methods , Hydrophobic and Hydrophilic Interactions , Nucleosides/chemistry , Nucleotides/chemistry , Reproducibility of Results , Silicon Dioxide/chemistry , Spectrometry, Mass, Electrospray Ionization/instrumentation , Surface Properties , Tandem Mass Spectrometry/instrumentationABSTRACT
A gas chromatography-microchip atmospheric pressure photoionization-tandem mass spectrometry (GC-µAPPI-MS/MS) method was developed for the analysis of anabolic androgenic steroids in urine as their trimethylsilyl derivatives. The method utilizes a heated nebulizer microchip in atmospheric pressure photoionization mode (µAPPI) with chlorobenzene as dopant, which provides high ionization efficiency by producing abundant radical cations with minimal fragmentation. The performance of GC-µAPPI-MS/MS was evaluated with respect to repeatability, linearity, linear range, and limit of detection (LOD). The results confirmed the potential of the method for doping control analysis of anabolic steroids. Repeatability (RSD<10%), linearity (R(2)≥0.996) and sensitivity (LODs 0.05-0.1ng/mL) were acceptable. Quantitative performance of the method was tested and compared with that of conventional GC-electron ionization-MS, and the results were in good agreement.
Subject(s)
Anabolic Agents/urine , Chlorobenzenes/chemistry , Gas Chromatography-Mass Spectrometry/methods , Anabolic Agents/chemistry , Androgens/chemistry , Androgens/urine , Humans , Limit of Detection , Linear Models , Methyltestosterone/chemistry , Methyltestosterone/urine , Models, Molecular , Nandrolone/chemistry , Nandrolone/urine , Photochemical Processes , Reproducibility of Results , Tandem Mass Spectrometry/methodsABSTRACT
A new and simple APPI interface employing commercially available hardware is used to combine GC to MS. The feasibility of the method is demonstrated in the analysis of urine samples for neurosteroids as their trimethylsilyl (TMS) derivatives. The effect of different dopants (chlorobenzene, toluene, anisole) on the ionization of the TMS derivatives was investigated. With chlorobenzene, the TMS derivatives produced intense molecular ions with minimal fragmentation, and chlorobenzene was selected as best dopant. Protonated molecules in addition to intense molecular ions were produced with toluene and anisole. The performance of the method was verified in the analysis of human urine samples. Chromatographic performance was good with peak half-widths of 3.6-4.3s, linearity (r(2)>0.990) was acceptable, limits of detection (LODs) were in the range of 0.01-10ngmL(-1), and repeatability was good with relative standard deviations (rsd%) below 22%. The results show that the method is well suited for the determination of neurosteroids in biological samples.