The infraacetabular screw versus the antegrade posterior column screw in acetabulum fractures with posterior column involvement: a biomechanical comparison.

INTRODUCTION: Traditionally, plate osteosynthesis of the anterior column combined with an antegrade posterior column screw is used for fixation of anterior column plus posterior hemitransverse (ACPHT) acetabulum fractures. Replacing the posterior column screw with an infraacetabular screw could improve the straightforwardness of acetabulum surgery, as it can be inserted using less invasive approaches, such as the AIP/Stoppa approach, which is a well-established standard approach. However, the biomechanical stability of a plate osteosynthesis combined with an infraacetabular screw instead of an antegrade posterior column screw is unknown. MATERIAL AND METHODS: Two osteosynthesis constructs were compared in a synthetic hemipelvis model with an ACPHT fracture: Suprapectineal plate + antegrade posterior column screw (APCS group) vs. suprapectineal plate + infraacetabular screw (IAS group). A single-leg stance test protocol with an additional passive muscle force and a cyclic loading of 32,000 cycles with a maximum effective load of 2400 N was applied. Interfragmentary motion and rotation of the three main fracture lines were measured. RESULTS: At the posterior hemitransverse fracture line, interfragmentary motion perpendicular to the fracture line (p < 0.001) and shear motion (p < 0.001) and at the high anterior column fracture line, interfragmentary motion longitudinal to the fracture line (p = 0.017) were significantly higher in the IAS group than in the APCS group. On the other hand, interfragmentary motion perpendicular (p = 0.004), longitudinal (p < 0.001) and horizontal to the fracture line (p = 0.004) and shear motion (p < 0.001) were significantly increased at the low anterior column fracture line in the APCS group compared to the IAS group. CONCLUSIONS: Replacing the antegrade posterior column screw with an infraacetabular screw is not recommendable as it results in an increased interfragmentary motion, especially at the posterior hemitransverse component of an ACPHT fracture.

Postoperative lymphedema after primary total hip arthroplasty: prospective analysis of bikini incision-type direct anterior approach versus established standard approaches.

BACKGROUND: Minimally invasive approaches to the hip joint for total hip arthroplasty such as the DAA ("Direct Anterior Approach with bikini incision") are increasingly utilized. According to the literature, this approach is more muscle-sparing, results in less postoperative pain, and achieves higher patient satisfaction. The existence of postoperative lymphedema after hip arthroplasty is hardly considered. The aim of this paper is to contribute to the evaluation of the different access methods related to postoperative lymphedema and their functional outcomes. METHODS: This is a prospective non-randomized study at an orthopedic specialist clinic in Northern Europe. The surgeons that performed the arthroplasties are high-volume surgeons in private practice affiliated to the clinic. The study included 188 patients with primary hip arthroplasty in a 1:1 ratio (DAA: standard accesses (posterior, transgluteal, and anterolateral access)). Epidemiologic data, Harris Hip Score, Oxford Hip Score, European Quality of Life 5, and Visual Analog Scale were collected preoperatively on admission day, 3rd and 5th postoperative day, and follow-up after 1 year. Furthermore, the range of motion, gait, and ability to climb stairs, as well as the presence of hypesthesia were assessed. To evaluate the edema situation, both legs were measured on the 3rd and 5th postoperative day. The prescription of manual lymphatic drainage and remaining swelling conditions 1 year postoperatively were recorded. RESULTS: For each group, 94 patients with a mean age of 61.7 years (DAA 60.7 and standard access 62.6) were included. All but one patient in the DAA group showed postoperative lymphedema (n: 93/94; 98.9%). In the standard surgery group, only n: 37/94 (39.4%) showed swelling symptoms requiring treatment. After 1 year, lymphedema persisted in 20 patients in the DAA group and 0 patients in the standard-OR group. Hypesthesia at the ventral thigh persisted in 16/94 (= 17%) patients of the DAA group versus 0/94 patients of the standard group after 12 months. Of these 16 cases, 10 had concomitant edema (62.5%). The DAA showed better results than the standard accesses in terms of Oxford Hip Score (p < 0.05) and ability to climb stairs (p < 0.05). In contrast, the Visual Analog Scale and patient quality of life results showed no significant difference (p > 0.05). CONCLUSION: The present study demonstrated the increased incidence of postoperative lymphedema in patients operated on via DAA access using a Bikini-type skin incision. In the follow-up, significantly more hypesthesia of the ventral thigh occurred in the DAA group. Otherwise, the DAA proved to be superior to the standard approaches from a functional point of view at short-term follow-up. Future research is needed to compare the horizontally oblique to the longitudinal oblique skin incision technique in direct anterior hip surgery regarding the above-mentioned adverse effects found in this study.

Operative versus conservative treatment in pelvic ring fractures with sacral involvement.

BACKGROUND: To evaluate the performance in activities of daily living (ADL), level of pain, mortality and rate of complications in patients with a pelvic ring fracture with sacral involvement who were treated conservatively compared to a surgically treated patient collective using percutaneous iliosacral screw fixation. HYPOTHESIS: Conservative treatment does not result in inferior clinical outcome compared to operative treatment. PATIENTS AND METHODS: A retrospective study of 112 conservatively (n=46) or operatively (n=66) treated patients with an isolated posterior or a combined posterior and anterior pelvic ring fracture was performed. The analysis included: age, sex, mechanism of injury, fracture type according to AO/OTA classification, energy of trauma sustained (no-, low-, high-energy trauma), type of treatment (operative or conservative), complications as well as duration of in-hospital stay. To assess clinical and activity outcome, the visual analog scale for pain (VAS), Barthel Scale, American Society of Anaesthesiologists (ASA) scores as well as mortality were assessed. The mean follow-up was 29.3±14.6 months. Furthermore, a geriatric subgroup (n=68, age≥60, low-energy trauma only) was analyzed. RESULTS: The majority of the patients were female (79%) and suffered from low-energy trauma (n=64, 58%). There were no significant differences in the operative and the conservative groups and subgroups concerning VAS, Barthel scores and ASA scores. The survival analyses showed a significantly lower survival rate in the conservative group (41.8±3.6 months) compared to the operative group (55.9±2 months, p=0.002). Similar findings were encountered in the geriatric subgroup analysis. CONCLUSION: This study demonstrates equivalent clinical outcome in conservatively and surgically treated patients using a percutaneous iliosacral screw fixation at a mid-term follow-up. However, operatively treated patients showed decreased mortality. This needs to be carefully considered in clinical decision-making but must be further explored using a prospective randomized study approach. LEVEL OF EVIDENCE: III.

Conservative versus operative treatment of FFP II fractures in a geriatric cohort: a prospective randomized pilot trial.

A clear recommendation regarding treatment strategy of fragility fractures of the pelvic ring is missing. The most typical fracture pattern is a lateral compression type injury with non-displaced fractures of the anterior pubic rami and a unilateral os sacrum fracture (FFP II). We hypothesized that operative treatment would be superior to conservative treatment. From October 2017 to April 2020, a randomized prospective non-blinded trial with n = 39 patients was carried out. Two arms with 17 operative versus 22 conservative cases were created. Inclusion criteria were a posterior pelvic ring fracture FFP type II, age over 60 years and acute fracture (< 3 weeks). Barthel index, pain level (VAS), quality of life (EQ-5D-3L), and Tinetti-Gait Test were determined on admission, at discharge, and after 3, 6, 12 and 24 months. Median follow-up was 12.9 months. The Barthel index (= 0.325), VAS (p = 0.711), quality of life (p = 0.824), and Tinetti-Gait Test (p = 0.913) showed no significant differences between the two groups after 12 months. Two patients switched from the conservative to the operative arm due to persistent immobilization and pain. The one-year mortality rate showed no significant difference (p = 0.175). Our hypothesis that surgical treatment is superior was refuted. No significant benefit was shown in terms of quality of life, mortality and pain levels. The results suggest a more differentiated treatment approach in the future, with initial conservative treatment preferred. A larger multi-center trial is required to confirm these findings.Trial registration: The study was retrospectively registered with the German Clinical Trials Registry (DRKS00013703) on 10/12/2018.

Comparison of different intraoperative reduction monitoring methods in a cadaveric intraarticular calcaneal fracture model: 3D scan vs arthroscopy vs nanoscopy.

AIMS: Visualization of the subtalar joint surface in surgical management of calcaneal factures remains a big challenge and anatomic reduction of the articular surface is essential for a good clinical outcome. We hypothesize that video-assistance can provide superior fracture reduction compared to fluoroscopy and that nanoscopy (NSC) achieves more extensive visualization compared to fracturoscopy (FSC). METHODS: Ten human cadaveric feet with artificially pre-fractured intraarticular calcaneal fractures with involvement of the posterior facet were treated via a minimal invasive subtalar approach. After initial control of reduction by 2D fluoroscopy, the reduction was further analyzed intraoperatively by FSC and NSC. 3D Scan served as gold standard control of reduction. Need of revision of reduction after the different visualization techniques was recorded and the extent of visualization of the subtalar joint surface in the medio-lateral dimension was compared for FSC and NSC. To quantify access and visualization of the medial and posterior facet, a depth gauge was used to measure from laterally at the clinically widest portion of the calcaneus targeted to the sustentaculum tali. The distance in millimetres was referred to the complete medio-lateral distance seen on paracoronal CT at the widest portion of the calcaneus. RESULTS: Fracture analysis in preoperative CT-scans according to Sanders classification revealed four type IC, two IIA, three IIC and one IIIAC fractures. Mean visualization of the medial and posterior facet was significantly improved with NSC (30.4 ± 3.78 mm) compared to FSC (23.6 ± 6.17 mm) (p = 0.008). An imperfect reduction requiring revision was more often required with NSC compared to FSC. Insufficient reduction using video-assistance was found in two cases. CONCLUSION: In order to optimize subtalar joint reduction and congruency, video-assisted techniques, especially NSC, provide superior visualization and thus can improve reduction in the surgical treatment of intraarticular calcaneal fractures.

Epidemiology and socioeconomic consequences of work-related pelvic and acetabular fractures recorded in the German Social Accident Insurance.

INTRODUCTION: Pelvic and acetabular fractures can result from work-related accidents and frequently require lengthy medical treatments. Consequently, high medical costs as well as delayed or absent return to work can be the consequence. Therefore, we aimed to study the socioeconomic consequences of work-related pelvic and acetabular fractures. MATERIALS AND METHODS: This retrospective study investigated work-related pelvic and acetabular fractures recorded in the German Social Accident Insurance in 2011 and 2017, in terms of age, sex, type of accident, duration of incapacity to work, reductions in earning capacity, costs for outpatient and inpatient treatment and costs for pension and severance pay. RESULTS: Among a total of 606 injuries in 2011 and 619 injuries in 2017, male patients and patients between 40 and 65 years were predominantly affected. Acetabular fractures caused higher rates of long absence from work of 6-12 months (2011: 24.7% vs. 9.5-16.9%; 2017: 26.1% vs. 6.1-11.0%) and >12 months (2011: 15.8% vs. 9.8-10.2%; 2017: 13.3% vs. 1.9-8.2%) as well as more cases with a reduction in earning capacity of at least 20% (2011: 61 vs. ≤27 cases; 2017: 39 vs. ≤12 cases) compared to pelvic ring fractures. The total costs for pelvic ring and acetabular fractures in the German social accident insurances amounted € 18,726,630 and € 9637,189 in the periods 2011-2020 and 2017-2020, respectively. The average costs per case for treatment and rehabilitation until 2020 was € 19,079 for injuries from 2011 and € 13,629 for injuries from 2017. Acetabular fractures were found to be the most cost-intensive injuries compared to anterior, posterior or complex pelvic ring fractures. CONCLUSIONS: Work-related pelvic and especially acetabular fractures have a considerable socioeconomic impact in the German Social Accident Insurance. Measures to prevent work-related accidents and to improve treatment of pelvic injuries can help to reduce their socioeconomic burden.

The influence of 3D printing on inter- and intrarater reliability on the classification of tibial plateau fractures.

PURPOSE: Tibial plateau fractures continue to be a challenging task in clinical practice and current outcomes seem to provide the potential for further improvement. Especially presurgical understanding of the orientation of fracture lines and fracture severity is an essential key to sufficient surgical treatment. The object of this study was to evaluate the reliability of modern axial CT-based classification systems for tibial plateau fractures. In addition, the diagnostic-added value of 3D printing on the classification systems was investigated. METHODS: 22 raters were asked to classify 22 tibial plateau fractures (11 AO B- and 11 AO C-fractures) with the AO, the 10-Segment and the Revisited Schatzker classification in a three-step evaluation: first only using CT scans, second with 3D volumetric reconstructions and last with 3D-printed fracture models. Inter- and intraobserver agreement and the subjective certainty were analyzed. Statistics were done using kappa values, percentage match and a univariant one-way analysis of variance. RESULTS: The AO classifications interobserver percentage match and kappa values improved for all raters and recorded an overall value of 0.34, respectively, 43% for the 3D print. The 10-Segment classification interobserver agreement also improved with the 3D-printed models and scored an overall kappa value of 0.18 and a percentage match of 79%. Equally the Revisited Schatzker classification increased its values to 0.31 and 35%. The intraobserver agreement showed a moderate agreement for the AO (0.44) and Revisited Schatzker classification (0.42) whereas the 10-Segment classification showed a fair agreement (0.27). Additionally, the raters changed their classification in 36% of the cases after evaluating the fracture with the 3D-printed models and the subjective certainty regarding the decisions improved as categories of self-reliant diagnostic choices were selected 18% (p < 0.05) more often after using the 3D-printed models. CONCLUSION: Based on the measured outcomes it was concluded that the new classification systems show an overall slight to fair reliability and the use of 3D printing proved to be beneficial for the preoperative diagnostics of tibial plateau fractures. The 10-Segment classification system showed the highest percentage match evaluation of all classification systems demonstrating its high clinical value across all levels of user experience.

A Register Analysis after Tibial Plateau Fracture in Statutory Accident Insurance. / Ergebnisse und Kosten nach Tibiakopffraktur in der gesetzlichen Unfallversicherung ­ eine Registeranalyse.

OBJECTIVE: To analyse the results after tibial plateau fractures with a focus on socioeconomic consequences. METHODS: On the basis of the data from the rehabilitation documentation of the German Statutory Accident Insurance (DGUV) on tibial plateau fractures (Code 83), a retrospective anonymised evaluation of the injuries which occurred in 2010 and 2016 was carried out. The registry data allowed subdivision into 3 groups: Medial, lateral and bicondylar tibial plateau fractures. The data have been analysed with regard to the following parameters: age, gender, treatment, time of return to work (AU), costs per case, total costs, workers compensation (MdE) and total payments. RESULTS: The analysis includes 1046 isolated tibial plateau fractures for 2010 and 1072 for 2016. In 2016, 798 fractures could be assigned to the medial, lateral or bicondylar fracture groups. In 551 cases, both condyles were involved. In another 221 cases, the lateral plateau and in 26 the medial plateau was injured. There were 476 (59.7%) men and 322 (40.4%) women. The mean age was 43.4 (SD ± 16.7) years with a peak of 180 cases in the 55-60 year subgroup and 98 aged 15-20 years. The mean age of the cases with isolated lateral plateau involvement was 48.1 (SD ± 13.8) and was 47.5 (SD ± 16.6) in those with medial plateau fractures and 41.4 (SD ± 17.2) years in the subgroup with bicondylar patterns. The mean time of return to work was 39.4 (SD ± 25.3) weeks for the bicondylar tibial plateau fractures, 28.1 (SD ± 27.2) weeks for the medial and 24.5 (SD ± 22.8) weeks for the lateral groups. For the 2016 group, the mean costs were 5212 € for outpatient, 10358 € for inpatient and 7622 € for rehab costs per case (total costs over three years of 4247443 € for outpatient and 7506508 € for acute inpatient treatment). The highest costs per case were caused by the inpatient acute treatment of bicondylar tibial plateau fractures, at a mean of 22292 €. 17.6% of the 2016 casualty group resulted in compensation of at least 20%. The treatment costs for the 2010 group over 9 years (2010-2019) amounted to 4190855 € for outpatient treatments and € 9565313 for inpatient treatments. In addition, compensations of 8632448 € and lump-sum payments of 483289 € were paid from 2010 to 2019. Over a period of 9 years, 456 (66%) of 692 patients needed another in patient follow-up treatment. A total of 51% (n = 353) needed these treatments within the first year. CONCLUSION: Tibial plateau fractures, in particular bicondylar tibial plateau fractures, show long-term, cost-intensive healing processes with reduced occupational capacity. Tibial plateau fractures are of economic importance in the statutory accident insurance in the long term. Preventive measures, optimal care and rehabilitation are therefore essential, together with innovative research to improve clinical outcomes.

Does the COVID-19 personal protective equipment impair the surgeon's performance?

INTRODUCTION: Despite increasing vaccination rates, new viral variants of SARS-CoV-2 (severe acute respiratory syndrome coronavirus type 2) are advancing the COVID 19 (coronavirus disease 2019) pandemic and continue to challenge the entire world. Surgical care of SARS-CoV-2 positive patients requires special protective measures. We hypothesized that "COVID-19" personal protective equipment (PPE) during surgery of SARS-CoV-2 positive or potentially positive patients would negatively affect the surgeon and thus the surgical outcome. MATERIALS AND METHODS: Ten experienced trauma surgeons participated in the study. Each surgeon performed two simulated surgeries of a distal tibial fracture on a Sawbone® under standardized conditions either wearing regular PPE or special COVID-19 PPE. Baseline values at rest were acquired for heart rate, blood pressure, saturation of peripheral oxygen (SpO2), respiratory rate and capillary blood gas (CBG) analysis including capillary partial pressure of oxygen (pO2) and carbon dioxide (pCO2), followed by four different standardized tests of attentional performance (TAP). Subsequently, the surgeon performed the first surgery according to a randomly determined order, with regular or COVID-19 PPE conditions in an operation theatre. After each surgery vital signs were acquired and CBG and TAP were performed again. RESULTS: In our simulated surgical procedure heart rate, respiratory rate, systolic and diastolic blood pressure did not show relevant differences. Percutaneously measured SpO2 decreased with additional layers of PPE, while CBG parameters were not affected. TAP tests showed a significant impairment of attention if PPEs were compared to the baseline, but both PPEs had similar results and no meaningful differences could be measured. CONCLUSIONS: According to our results, for surgical procedures additional PPE required during COVID-19 pandemic does not relevant affect the surgeon's mental and physical performance. Surgeries under COVID-19 PPE conditions appear safe and do not increase patient risk. LEVEL OF EVIDENCE: Level I.

Full endoscopic anterior intrapelvic plate osteosynthesis: a cadaveric feasibility study.

In this investigation, it was assumed that it must be possible to visualize the intrapelvic aspect as accustomed by pelvic surgeons using the anterior intrapelvic (modified Stoppa) approach. Moreover, it was hypothesized, that plate mountings will not only be possible for the symphysis but also at the supra- and infrapectineal aspect as well as to the posterior column. Ten anonymized cadaveric specimens were included in this study. A standard laparoscopic totally extraperitoneal (TEP) approach was used. A total of 10 landmarks were defined that are usually within reach in the open anterior intrapelvic (AIP) approach. Moreover, five different plate mountings were tested. The locations were chosen in accordance with the indication spectrum suitable for open surgery through the traditional AIP approach. It was possible to gain intrapelvic visibility in seven of ten cases. In all of those seven cases, it was technically possible to place plates to the symphysis, superior pubic ramus, as well as longer anterior column plates up to the aspect posterior of the acetabulum. In the last four of the seven cases, it was possible to mount plates to the infrapectineal aspect as well as the posterior column, too. The team, previously trained in arthroscopic surgical techniques as well as pelvic trauma surgery, observed a steep learning curve. This investigation demonstrated, that endoscopic anterior intrapelvic plate osteosynthesis was feasible in the majority of the cases in a series of ten cadaveric models. New instruments will be needed such as extra-long rasp elevators, ball-spikes as well as devices to hold and position plates and extra-long self-holding screwdrivers. With these, endoscopic pelvic surgery will likely be a realistic option for selected pelvic trauma cases in the future.

Anterolateral versus modified posterolateral approach for tibial plateau fractures with involvement of the posterior column: a cadaveric study.

INTRODUCTION: The aim of this study was to compare the reduction quality of the anterolateral (AL) and modified posterolateral approach (PL) in lateral tibial plateau fractures involving the posterior column and central segments. METHODS: Matched pairs of pre-fractured cadaveric tibial plateau fractures were treated by either AL approach (supine position) or PL approach (prone position). Reduction was controlled by fluoroscopy and evaluated as satisfying or unacceptable. Afterwards, the reduction was examined by 3D scan. RESULTS: 10 specimens (3 pairs 41B3.1, 2 pairs 41C3.3) were evaluated. PL approach achieved significantly (p 0.00472) better fracture reduction results (0.4 ± 0.7 mm) of the posterior column compared to the AL group (2.1 ± 1.4 mm). Fracture steps involving the central area of the lateral plateau were insufficiently reduced after fluoroscopy using both approaches. CONCLUSION: Optimal reduction of displaced tibial plateau fractures involving the posterolateral column necessitates a posterior approach, which can be conducted in prone or lateral positioning. The anterolateral approach is indicated in fractures with minor displacement of the posterolateral rim but fracture extension in the latero-central segments. In these cases, an additional video-assisted reduction or extended approaches are helpful.

Neurogenic gluteus medius and minimus muscle atrophy with Trendelenburg's sign after a displaced acetabular fracture of the posterior column - A case report.

Traumatic or iatrogenic sciatic nerve injury, but not superior gluteal nerve injury, is a well described complication after acetabular fractures. Most often, sciatic nerve injuries occur in fractures involving the posterior column/wall with a hip dislocation and posterior fracture displacement resulting in narrowing of the greater sciatic foramen and injuring the sciatic nerve passing through. In this case report, a case of abductor mechanism deficiency with positive Trendelenburg's sign after an acetabular fracture of the posterior column with hip dislocation is presented. Postoperative clinical and MRI examination revealed a neurogenic atrophy of gluteus medius and minimus muscles suggesting a superior gluteal nerve injury due to initial subtotal incarceration of the greater sciatic foramen by a displaced posterior fracture fragment. An additional mild sciatic nerve injury resolved in the early postoperative course, while intensive physiotherapy improved the patient's complaints and muscular atrophy caused by the superior gluteal nerve injury within 12 months. This case report intends to raise awareness for rare neurological complications after acetabular fractures for their early detection.

Biomechanical in vitro analysis of a novel flexible implant for pubic symphysis disruption using an ultra-high molecular weight polyethylene fiber cord.

BACKGROUND: Plate osteosynthesis depicts the gold standard to surgically treat pubic symphysis disruptions. However, high rates of implant failure after plate osteosynthesis are reported, probably because of the iatrogenic arthrodesis of this fibrocartilaginous joint. Therefore, flexible implants for treatment of pubic symphysis disruptions appear to be a sensible solution. METHODS: In this biomechanical screening study, we designed and investigated a flexible implant, which consists of two plates connected with an ultra-high molecular weight polyethylene fiber cord. We mechanically tested eye splices as a possible fixation method of the cords by performing tensile load to failure tests. Afterwards, we developed a biomechanically appropriate plate design and cord routing between the plates. Finally, we biomechanically tested the flexible implant under tensile and shear loading until failure. FINDINGS: When fixing a 1 mm ultra-high molecular weight polyethylene fiber cord with eye splices, a load at failure of 1570.74 N was detected under tensile loading. None of the eye splices failed but the cords itself ruptured. The load at failure of the designed cord routing in criss-cross technique and fixation within the plates amounts 4742.09 N under tensile and 2699.77 N under shear load. INTERPRETATION: We developed a novel flexible implant for repair of pubic symphysis disruptions using ultra-high molecular weight polyethylene fiber cords connected to osteosynthesis plates. We identified eye splices as a mechanically optimal fixation method and proved that the ultra-high molecular weight polyethylene fiber cord routing and fixation of the flexible implant clearly withstands physiological forces acting on the pubic symphysis.

Biomechanical analysis of fixation methods in acetabular fractures: a systematic review of test setups.

PURPOSE: Optimal anatomical reduction and stable fixation of acetabular fractures are important in avoiding secondary dislocation and osteoarthritis. Biomechanical studies of treatment options of acetabular fractures aim to evaluate the biomechanical properties of different fixation methods. As the setup of the biomechanical test can influence the experimental results, this review aimed to analyze the characteristics, comparability and clinical implications of studies on biomechanical test setups and finite element analyses in the fixation of acetabular fractures. METHODS: A systematic literature research was conducted according to the PRISMA guidelines, using the PubMed/MEDLINE and Web of Science databases. 44 studies conducting biomechanical analyses of fixation of acetabular fractures were identified, which met the predefined inclusion and exclusion criteria and which were published in English between 2000 and April 16, 2021. The studies were analyzed with respect to distinct parameters, including fracture type, material of pelvis model, investigated fixation construct, loading direction, loading protocol, maximum loading force, outcome parameter and measurement method. RESULTS: In summary, there was no standardized test setup within the studies on fixation constructs for acetabular fractures. It is therefore difficult to compare the studies directly, as they employ a variety of different test parameters. Furthermore, the clinical implications of the biomechanical studies should be scrutinized, since several test parameters were not based on observations of the human physiology. CONCLUSION: The limited comparability and restricted clinical implications should be kept in mind when interpreting the results of biomechanical studies and when designing test setups to evaluate fixation methods for acetabular fractures.

Stresses and deformations of an osteosynthesis plate in a lateral tibia plateau fracture.

This study has the aim to investigate the strain and stress in an anterolateral locking plate applied for the fixation of a lateral split fracture. To simulate a complex fracture situation, three segments were separated. With a FEM analysis, representative places for strain and stress measurement were determined. A locked osteosynthesis plate was instrumented with strain gauges and tested on a fractured and a non-fractured Saw Bone model. To simulate different loading situations, four different points of force application, from the center of the condyles to a 15 mm posterior position, were used with a medial-lateral load distribution of 60:40. The simulations as well as the biomechanical tests demonstrated that two deformations dominate the load on the plate: a bending into posterior direction and a bulging of the plate head. Shifting the point of application to the posterior direction resulted in increasing maximum stress, from 1.16 to 6.32 MPa (FEM analysis) and from 3.04 to 7.00 MPa (biomechanical study), respectively. Furthermore, the comparison of the non-fractured and fractured models showed an increase in maximum stress by the factor 2.06-2.2 (biomechanical investigation) and 1.5-3.3 (FEM analysis), respectively.

A comparison between Asians and Caucasians in the dimensions of the femoral isthmus based on a 3D-CT analysis of 1189 adult femurs.

INTRODUCTION: For successful intramedullary implant placement at the femur, such as nailing in unstable proximal femur fractures, the use of an implant that at least reaches or exceeds the femoral isthmus and yields sufficient thickness is recommended. A number of complications after intramedullary femoral nailing have been reported, particularly in Asians. To understand the anatomical features of the proximal femur and their ethnic differences, we aimed to accurately calculate the femoral isthmus dimensions and proximal distance of Asians and Caucasians. METHODS: In total, 1189 Asian and Caucasian segmented 3D CT data sets of femurs were analyzed. The individual femoral isthmus diameter was precisely computed to investigate whether gender, femur length, age, ethnicity or body mass index have an influence on isthmus diameters. RESULTS: The mean isthmus diameter of all femurs was 10.71 ± 2.2 mm. A significantly larger diameter was found in Asians when compared to Caucasians (p < 0.001). Age was a strong predictor of the isthmus diameter variability in females (p < 0.001, adjusted r2 = 0.299). With every year of life, the isthmus showed a widening of 0.08 mm in women. A Matched Pair Analysis of 150 female femurs showed a significant difference between isthmus diameter in Asian and Caucasian femurs (p = 0.05). In 50% of the cases the isthmus was found in a range of 2.4 cm between 16.9 and 19.3 cm distal to the tip of the greater trochanter. The female Asian femur differs from Caucasians as it is wider at the isthmus. CONCLUSIONS: In absolute values, the proximal isthmus distance did not show much variation but is more proximal in Asians. The detailed data presented may be helpful in the development of future implant designs. The length and thickness of future standard implants may be considered based on the findings.

The influence of bone quality on radiological outcome in 50 consecutive acetabular fractures treated with a pre-contoured anatomic suprapectineal plate.

PURPOSE: To investigate the range of indications of an anatomical-preshaped three-dimensional suprapectineal plate and to assess the impact of the bone mass density on radiologic outcomes in different types of acetabular fractures. PATIENTS AND METHODS: A consecutive case series of 50 acetabular fractures (patient age 69 ± 23 years) treated with suprapectineal anatomic plates were analyzed in a retrospective study. The analysis included: Mechanism of injury, fracture pattern, surgical approach, need for additional total hip arthroplasty, intra- or postoperative complications, as well as bone mass density and radiological outcome on postoperative computed tomography. RESULTS: Most frequently, anterior column fracture patterns with and without hemitransverse components as well as associated two column fractures were encountered. The anterior intrapelvic approach (AIP) was used in 98% (49/50) of the cases as primary approach with additional utilization of the first window of the ilioinguinal approach in 13/50 cases (26%). Determination of bone density revealed impaired bone quality in 70% (31/44). Postoperative steps and gaps were significantly greater in this subgroup (p < 0.05). Fracture reduction quality for postoperative steps revealed anatomic results in 92% if the bone quality was normal and in 46% if impaired (p < 0.05). In seven cases (14%), the plate was utilized in combination with acute primary arthroplasty. CONCLUSION: A preshaped suprapectineal plate provides good radiological outcomes in a variety of indications in a predominantly geriatric cohort. Impaired bone quality has a significantly higher risk of poor reduction results. In cases with extensive joint destruction, the combination with total hip arthroplasty was a valuable option.

Improved Visualization by Central Subluxation of the Lateral Meniscus in Comminuted Lateral Tibial Plateau Fractures.

The goal of surgical reconstruction of comminuted tibial plateau fractures is an anatomical reconstruction and stable fixation of the articular surface. This can be difficult due to poor visualization of the posterolateral and central segments of the articular surface of the proximal tibia. To improve visualization, the lateral approach can be extended with an osteotomy of the femoral epicondyle. In most cases, use of the extended lateral approach allows the whole lateral plateau to be visualized. Nevertheless, in some cases, an osteotomy alone is not enough to expose the entire fracture, especially the central segments of the tibial plateau. For these specific cases, we developed an additional technical trick that significantly improves articular visualization; the lateral meniscocapsular fibers are dissected allowing for central subluxation of the lateral meniscus, while leaving the anterior and posterior roots intact. With central subluxation of the lateral meniscus in comminuted tibial plateau fractures, the joint surface can be completely visualized, allowing an anatomical reduction even in highly complex fractures.

Biomechanical analysis of anterior pelvic ring fractures with intact peripelvic soft tissues: a cadaveric study.

PURPOSE: Biomechanical studies of the pelvis are usually performed using dissected pelvic specimens or synthetic bones. Thereby the stabilising effect of the surrounding soft tissues is analysed insufficiently. Biomechanical data for isolated anterior pelvic ring fractures are currently missing. Therefore, the purpose of this study was to develop a novel testing device for biomechanical analyses of the pelvis and to investigate two different anterior pelvic ring fractures in a cadaveric model with intact peripelvic soft tissues. METHODS: A new biomechanical table construction which enables the fixation and testing of complete cadaveric specimens was developed. It was used to investigate the relative motion and stiffness changes due to unilateral osteotomy of the superior and inferior pubic ramus. Five cadavers with a mean age of 55.6 years (± 15.53 years) were included and loaded with a sinusoidal, cyclic (1 Hz), compressive force of up to 365 N over ten cycles for each condition. RESULTS: Biomechanical testing of the pelvis with complete appended soft tissues was feasible. Native stiffness without a pelvic fracture was 64.31 N/mm (± 8.33 N/mm). A standardised unilateral osteotomy of the superior pubic ramus reduced the stiffness under isolated axial load by 2% (63.05 N/mm ± 7.45 N/mm, p = 0.690). Additional osteotomy of the inferior pubic ramus caused a further, statistically not significant, decrease by 5% (59.57 N/mm ± 6.84 N/mm, p = 0.310). CONCLUSIONS: The developed test device was successfully used for biomechanical analyses of the pelvis with intact peripelvic soft tissues. In a first study, isolated unilateral fractures of the anterior pelvic ring showed no relevant biomechanical variation compared to the intact situation under isolated axial load. Only 7% of the measured stiffness was created by both unilateral pubic rami. Therefore, the clinical practice to treat unilateral anterior pelvic ring fractures conservatively is supported by the results of this study.

Clinical results after surgical treatment of posterolateral tibial plateau fractures ("apple bite fracture") in combination with ACL injuries.

PURPOSE: The anterior cruciate ligament (ACL)-tear is a common injury in orthopaedic trauma. Depending on the energy of impact fractures of the posterolateral tibial plateau are often associated. Different morphologic variants of posterolateral tibial plateau impaction fractures have been described in the setting of an ACL-tear. Up to now an algorithm of treatment for a combined injury of a posterolateral tibial head fracture and an injury to the anterior cruciate ligament is missing. METHODS: We present a retrospective study with clinical and radiological analysis of posterolateral fractures in combination with ACL-tear. Impressions with a depth of more than 2 mm and/or a width that outreaches more than half of the posterior horn of the lateral meniscus with additional 3. degree positive pivot-shift-test indicated surgical treatment of the fracture with additional ACL repair or reconstruction. Clinical evaluation included follow-up examination, Visual Analog Scale (VAS), International Knee Documentation Committee Score (IKDC), functional and radiological Rasmussen score. RESULTS: 20 patients were included with a mean age of 43.6 ± 12.4 years. Mean follow-up was 18,2 ± 13,5 months. The fracture was arthroscopically reduced and percutaneously fixed with a screw osteosynthesis (Group 1), reduced via a dorsal approach without (Group 2) or with an autologous bone graft (Group 3). Subjective IKDC score was 79,15 ± 6,07. Functional Rasmussen scores ranged from 27 to 30 (mean 28 ± 2.71). Radiological Rasmussen scores ranged from 16 to 18 points (mean 16.75 ± 1.33). According to IKDC score (p = 0.60), functional Rasmussen score (p = 0.829) and radiological Rasmussen score (p = 0.679) no significant discrepancy between the groups were seen. There was no failure of the ACL graft recorded. CONCLUSIONS: Posterolateral tibial plateau fractures in combination with an ACL-tear, can cause persistent instability and increase rotational instability. Indication for treatment of these fractures is still under debate. From the biomechanical aspect the lack of more than 50% of the posterior horn of the lateral meniscus and dislocation/depression of more than 2 mm results in an increased rotational instability of the ACL deficient knee. Combined surgical treatment with ACL repair or reconstruction is a safe procedure that results in good, short-term clinical outcome, if our algorithm is followed. In addition this study shows, that majority of posterolateral tibial plateau fractures can be treated arthroscopically.