ABSTRACT
Metal halide perovskite solar cells have achieved tremendous progress and have attracted enormous research and development efforts since the first report of demonstration in 2009. Due to fabrication versatility, many heat treatment methods can be utilized to achieve perovskite film crystallization. Herein, 10.6 µm carbon dioxide laser process is successfully developed for the first time for perovskite film crystallization. In addition, this is the first time formamidinium lead triiodide solar cells by laser annealing under ambient are demonstrated. The champion cell produces a power conversion efficiency of 21.8%, the highest for laser-annealed perovskite cells. And this is achieved without any additive, passivation, or post-treatment.
ABSTRACT
Two-dimensional (2D) organic-inorganic metal halide perovskites have gained immense attention as alternatives to three-dimensional (3D) perovskites in recent years. The hydrophobic spacers in the layered structure of 2D perovskites make them more moisture-resistant than 3D perovskites. Moreover, they exhibit unique anisotropic electrical transport properties due to a structural confinement effect. In this study, four lead-free Dion-Jacobson (DJ) Sn-based phase perovskite single crystals, 3AMPSnI4, 4AMPSnI4, 3AMPYSnI4, and 4AMPYSnI4 [AMP = (aminomethyl)-piperidinium, AMPY = (aminomethyl)pyridinium] are reported. Results reveal structural differences between them impacting the resulting optical properties. Namely, higher octahedron distortion results in a higher absorption edge. Density functional theory (DFT) is also performed to determine the trends in energy band diagrams, exciton binding energies, and formation energies due to structural differences among the four single crystals. Finally, a field-effect transistor (FET) based on 4AMPSnI4 is demonstrated with a respectable hole mobility of 0.57 cm2 V-1 s-1 requiring a low threshold voltage of only -2.5 V at a drain voltage of -40 V. To the best of our knowledge, this is the third DJ-phase perovskite FET reported to date.
ABSTRACT
The rapid development of organic-inorganic hybrid perovskite solar cells has resulted in laboratory-scale devices having power conversion efficiencies that are competitive with commercialised technologies. However, hybrid perovskite solar cells are yet to make an impact beyond the research community, with translation to large-area devices fabricated by industry-relevant manufacturing methods remaining a critical challenge. Here we report the first demonstration of hybrid perovskite solar cell modules, comprising serially-interconnected cells, produced entirely using industrial roll-to-roll printing tools under ambient room conditions. As part of this development, costly vacuum-deposited metal electrodes are replaced with printed carbon electrodes. A high-throughput experiment involving the analysis of batches of 1600 cells produced using 20 parameter combinations enabled rapid optimisation over a large parameter space. The optimised roll-to-roll fabricated hybrid perovskite solar cells show power conversion efficiencies of up to 15.5% for individual small-area cells and 11.0% for serially-interconnected cells in large-area modules. Based on the devices produced in this work, a cost of ~0.7 USD W-1 is predicted for a production rate of 1,000,000 m² per year in Australia, with potential for further significant cost reductions.
ABSTRACT
Metal halide perovskite materials demonstrate immense potential for photovoltaic and electronic applications. In particular, two-dimensional (2D) layered metal halide perovskites have advantages over their 3D counterparts in optoelectronic applications due to their outstanding stability, structural flexibility with a tunable bandgap, and electronic confinement effect. This review article first analyzes the crystallography of different 2D perovskite phases [the Ruddlesden-Popper (RP) phase, the Dion-Jacobson (DJ) phase, and the alternating cations in the interlayer space (ACI) phase] at the molecular level and compares their common electronic properties, such as out-of-plane conductivity, crucial to vertical devices. This paper then critically reviews the recent development of optoelectronic devices, namely solar cells, photodetectors and field effect transistors, based on layered 2D perovskite materials and points out their limitations and potential compared to their 3D counterparts. It also identifies the important application-specific future research directions for different optoelectronic devices providing a comprehensive view guiding new research directions in this field.
ABSTRACT
Two-dimensional (2D) tin (Sn)-based perovskites have recently received increasing research attention for perovskite transistor application. Although some progress is made, Sn-based perovskites have long suffered from easy oxidation from Sn2+ to Sn4+ , leading to undesirable p-doping and instability. In this study, it is demonstrated that surface passivation by phenethylammonium iodide (PEAI) and 4-fluorophenethylammonium iodide (FPEAI) effectively passivates surface defects in 2D phenethylammonium tin iodide (PEA2 SnI4 ) films, increases the grain size by surface recrystallization, and p-dopes the PEA2 SnI4 film to form a better energy-level alignment with the electrodes and promote charge transport properties. As a result, the passivated devices exhibit better ambient and gate bias stability, improved photo-response, and higher mobility, for example, 2.96 cm2 V-1 s-1 for the FPEAI-passivated films-four times higher than the control film (0.76 cm2 V-1 s-1 ). In addition, these perovskite transistors display non-volatile photomemory characteristics and are used as perovskite-transistor-based memories. Although the reduction of surface defects in perovskite films results in reduced charge retention time due to lower trap density, these passivated devices with better photoresponse and air stability show promise for future photomemory applications.
ABSTRACT
Most of the reported 2D Ruddlesden-Popper (RP) lead halide perovskites with the general formula of An +1 Bn X3 n +1 (n = 1, 2, ) comprise layered perovskites separated by A-site-substituted organic spacers. To date, only a small number of X-site-substituted RP perovskites have been reported. Herein, the first inorganic-cation pseudohalide 2D phase perovskite single crystal, Cs2 Pb(SCN)2 Br2 , is reported. It is synthesized by the antisolvent vapor-assisted crystallization (AVC) method at room temperature. It exhibits a standard single-layer (n = 1) Ruddlesden-Popper structure described in space group of Pmmn (#59) and has a small separation (d = 1.69 Å) between the perovskite layers. The SCN- anions are found to bend the 2D Pb(SCN)2 Br2 framework slightly into a kite-shaped octahedron, limiting the formation of a quasi-2D perovskite structure (n > 1). This 2D single crystal exhibits a reversible first-order phase transformation to 3D CsPbBr3 (Pm3m #221) at 450 K. It has a low exciton binding energy of 160 meV-one of the lowest for 2D perovskites (n = 1). A Cs2 Pb(SCN)2 Br2 -single-crystal photodetector is demonstrated with respectable responsivity of 8.46 mA W-1 and detectivity of ≈1.2 × 1010 Jones at a low bias voltage of 0.5 V.
ABSTRACT
The power conversion efficiency (PCE) of solution-processed organic-inorganic mixed halide perovskite solar cells has achieved rapid improvement. However, it is imperative to minimize the voltage deficit (Woc = Eg /q - Voc ) for their PCE to approach the theoretical limit. Herein, the strategy of depositing homologous bromide salts on the perovskite surface to achieve a surface and bulk passivation for the fabrication of solar cells with high open-circuit voltage is reported. Distinct from the conclusions given by previous works, that homologous bromides such as FABr only react with PbI2 to form a large-bandgap perovskite layer on top of the original perovskite, this work shows that the bromide also penetrates the perovskite film and passivates the perovskite in the bulk. This is confirmed by the small-bandgap enlargement observed by absorbance and photoluminescence, and the bromide element ratio increasing in the bulk by time-of-flight secondary-ion mass spectrometry and depth-resolved X-ray photoelectron spectroscopy. Furthermore, a clear suppression of non-radiative recombination is confirmed by a variety of characterization methods. This work provides a simple and universal way to reduce the Woc of single-junction perovskite solar cells and it will also shed light on developing other high-performance optoelectronic devices, including perovskite-based tandems and light-emitting diodes.
ABSTRACT
This work reports strategies for improving the power conversion efficiency (PCE) by capitalizing on temporal changes through the storage effect and immediate improvements by interface passivation. It is demonstrated that both strategies can be combined as shown by PCE improvement in passivated perovskite solar cells (PSCs) upon ambient storage because of trap density reduction. By analyzing the dominant charge recombination process, we find that lead-related traps in perovskite bulk, rather than at the surface, are the recombination centers in both as-fabricated and ambient-stored passivated PSCs. This emphasizes the necessity to reduce intrinsic defects in the perovskite bulk. Furthermore, storage causes temporal changes in band alignment even in passivated PSCs, contributing to PCE improvement. Building on these findings, composition engineering was employed to produce further immediate PCE improvements because of defect reduction in the bulk, achieving a PCE of 22.2%. These results show that understanding the dominant recombination mechanisms within a PSC is important to inform strategies for producing immediate and temporal PCE enhancements either by interface passivation, storage, composition engineering, or a combination of them all to fabricate highly efficient PSCs.
ABSTRACT
Large magnetic optical rotary dispersion (Faraday rotation) has been demonstrated recently in methylammonium lead bromide. Here, we investigate the prospect of extending the active spectral range by altering the halogen. We also investigate the origins of large Faraday rotation in these diamagnetic materials using magnetic circular dichroism (MCD) spectroscopy and the Kramers-Kronig relations. We find that, while MAPbCl3 (MA = methylammonium) single crystals exhibit a large Verdet constant in the blue, no appreciable Faraday rotation is observed in the red/near infra-red for MAPbI3 single crystals. However, in all film samples, we find clear evidence of large MCD resulting from the Zeeman splitting of the highly resonant 1s exciton state. Our Kramers-Kronig calculations of Faraday rotation based on MCD data matches well with the dispersion of our experimental data for MAPbCl3 and MAPbBr3 , with some deviation in magnitude-demonstrating the excitonic nature of Faraday rotation in these materials. However, our calculations predict significant Faraday rotation in MAPbI3 , contrary to our experimental results, indicating a potential discrepancy between the properties of the thin film and single crystal.
ABSTRACT
All-inorganic CsPbI3 perovskite quantum dots have received substantial research interest for photovoltaic applications because of higher efficiency compared to solar cells using other quantum dots materials and the various exciting properties that perovskites have to offer. These quantum dot devices also exhibit good mechanical stability amongst various thin-film photovoltaic technologies. We demonstrate higher mechanical endurance of quantum dot films compared to bulk thin film and highlight the importance of further research on high-performance and flexible optoelectronic devices using nanoscale grains as an advantage. Specifically, we develop a hybrid interfacial architecture consisting of CsPbI3 quantum dot/PCBM heterojunction, enabling an energy cascade for efficient charge transfer and mechanical adhesion. The champion CsPbI3 quantum dot solar cell has an efficiency of 15.1% (stabilized power output of 14.61%), which is among the highest report to date. Building on this strategy, we further demonstrate a highest efficiency of 12.3% in flexible quantum dot photovoltaics.
ABSTRACT
Although perovskite solar cells have produced remarkable energy conversion efficiencies, they cannot become commercially viable without improvements in durability. We used gas chromatography-mass spectrometry (GC-MS) to reveal signature volatile products of the decomposition of organic hybrid perovskites under thermal stress. In addition, we were able to use GC-MS to confirm that a low-cost polymer/glass stack encapsulation is effective in suppressing such outgassing. Using such an encapsulation scheme, we produced multi-cation, multi-halide perovskite solar cells containing methylammonium that exceed the requirements of the International Electrotechnical Commission 61215:2016 standard by surviving more than 1800 hours of the Damp Heat test and 75 cycles of the Humidity Freeze test.
ABSTRACT
Lead halide perovskites (LHPs) have become a promising alternative for a wide range of optoelectronic devices, thanks to their solution-processability and impressive optical and electrical properties. More recently, LHPs have been investigated in magneto-optic studies and have exhibited spin-polarized emission, photoinduced magnetization, and long spin lifetimes. Here, the viability of methylammonium lead bromide (MAPbBr3) single crystals as solution-processed Faraday rotators is demonstrated. Compared to terbium gallium garnet, the industry standard in the visible, it is found that MAPbBr3 exhibits Verdet constants (i.e., strength of Faraday effect) of similar or greater magnitude (up to 2.5x higher), with lower temperature dependence. Due to its low trap absorption, it is calculated that an optical isolator made from MAPbBr3, with appropriate antireflection coatings, should reach ≈95% transmission and achieve 40 dB isolation for incoming powers of over 2 W. It is also shown that the Verdet constant of MAPbBr3 can be calculated accurately from its dispersion in refractive index, allowing the possibility to predict similar effects in other perovskite materials.
ABSTRACT
Improving the quality of perovskite poly-crystalline film is essential for the performance of associated solar cells approaching their theoretical limit efficiency. Pinholes, unwanted defects, and nonperovskite phase can be easily generated during film formation, hampering device performance and stability. Here, a simple method is introduced to prepare perovskite film with excellent optoelectronic property by using acetic acid (Ac) as an antisolvent to control perovskite crystallization. Results from a variety of characterizations suggest that the small amount of Ac not only reduces the perovskite film roughness and residual PbI2 but also generates a passivation effect from the electron-rich carbonyl group (C=O) in Ac. The best devices produce a PCE of 22.0% for Cs0.05FA0.80MA0.15Pb(I0.85Br0.15)3 and 23.0% for Cs0.05FA0.90MA0.05Pb(I0.95Br0.05)3 on 0.159 cm2 with negligible hysteresis. This further improves device stability producing a cell that maintained 96% of its initial efficiency after 2400 h storage in ambient environment (with controlled relative humidity (RH) <30%) without any encapsulation.
ABSTRACT
For the fabrication of perovskite solar cells (PSCs) using a solution process, it is essential to understand the characteristics of the perovskite precursor solution to achieve high performance and reproducibility. The colloids (iodoplumbates) in the perovskite precursors under various conditions were investigated by UV-visible absorption, dynamic light scattering, photoluminescence, and total internal reflection fluorescence microscopy techniques. Their local structure was examined by in situ X-ray absorption fine structure studies. Perovskite thin films on a substrate with precursor solutions were characterized by transmission electron microscopy, X-ray diffraction analysis, space-charge-limited current, and Kelvin probe force microscopy. The colloidal properties of the perovskite precursor solutions were found to be directly correlated with the defect concentration and crystallinity of the perovskite film. This work provides guidelines for controlling perovskite films by varying the precursor solution, making it possible to use colloid-engineered lead halide perovskite layers to fabricate efficient PSCs.
ABSTRACT
Halide perovskite materials are excellent light harvesters that have generated enormous interest for photovoltaic technology and an increasing number of other optoelectronic applications. Very recently, their use for miniaturized chemical sensors has shown a promising room-temperature response. Here, we present some insights on the use of CsPbBr2I (CPBI) perovskites for self-powered room-temperature sensing of several environmentally and medically relevant compounds demonstrating rapid detection of down to concentrations of 1 ppm. Notably, the photocurrent of these self-powered CPBI-based devices increases under exposure to both reducing (e.g. acetone, propane) and oxidizing (e.g. NO2, O2) gas molecules and decreases rapidly upon reverting to an inert atmosphere. In situ photoluminescence (PL) analysis of the CPBI during exposure to oxidizing molecules reveals a strongly increased PL intensity and longer lifetime indicating a prevalent role of CPBI trap states in the sensing mechanism. These findings provide new insights for the engineering of perovskite-based materials for their future chemical sensing applications.
ABSTRACT
An insight into the analogies, state-of-the-art technologies, concepts, and prospects under the umbrella of perovskite materials (both inorganic-organic hybrid halide perovskites and ferroelectric perovskites) for future multifunctional energy conversion and storage devices is provided. Often, these are considered entirely different branches of research; however, considering them simultaneously and holistically can provide several new opportunities. Recent advancements have highlighted the potential of hybrid perovskites for high-efficiency solar cells. The intrinsic polar properties of these materials, including the potential for ferroelectricity, provide additional possibilities for simultaneously exploiting several energy conversion mechanisms such as the piezoelectric, pyroelectric, and thermoelectric effect and electrical energy storage. The presence of these phenomena can support the performance of perovskite solar cells. The energy conversion using these effects (piezo-, pyro-, and thermoelectric effect) can also be enhanced by a change in the light intensity. Thus, there lies a range of possibilities for tuning the structural, electronic, optical, and magnetic properties of perovskites to simultaneously harvest energy using more than one mechanism to realize an improved efficiency. This requires a basic understanding of concepts, mechanisms, corresponding material properties, and the underlying physics involved with these effects.
ABSTRACT
This paper provides deep understanding of the formation mechanism of perovskite film fabricated by sequential solution-based methods. It compares two sequential spin-coating methods for Cs0.15 (MA0.7 FA0.3 )0.85 PbI3 perovskite. First is the "static process," with a stoppage between the two spin-coating steps (1st PbI2 -CsI-dimethyl sulfoxide (DMSO)-dimethylformamide (DMF) and 2nd methylammonium iodide (MAI)-formamidinium iodide (FAI)-isopropyl alcohol). Second is the "dynamic process," where the 2nd precursor is dispensed while the substrate is still spinning from the 1st step. For the first time, such a dynamic process is used for Cs0.15 (MA0.7 FA0.3 )0.85 PbI3 perovskite. Characterizations reveal improved film formation with the dynamic process due to the "retainment" of DMSO-complex necessary for the intermediate phase which i) promotes intercalation between precursors and ii) slows down perovskite crystallization for full conversion. The comparison on as-deposited perovskite before annealing indicates a more ordered film using this dynamic process. This results in a thicker, more uniform film with higher degree of preferred crystal orientation and higher carrier lifetime after annealing. Therefore, dynamic-processed devices present better performance repeatability, achieving a higher average efficiency of 17.0% compared to static ones (15.0%). The new insights provided by this work are important for perovskite solar cells processed sequentially as the process has greater flexibility in resolving solvent incompatibility, allowing separate optimizations and allowing different deposition methods.
ABSTRACT
Organic-inorganic metal halide perovskites have gained considerable attention for next-generation photovoltaic cells due to rapid improvement in power conversion efficiencies. However, fundamental understanding of underlying mechanisms related to light- and bias-induced effects at the nanoscale is still required. Here, structural variations of the perovskites induced by light and bias are systematically investigated using scanning probe microscopy techniques. We show that periodically striped ferroelastic domains, spacing between 40 to 350 nm, exist within grains and can be modulated significantly under illumination as well as by electric bias. Williamson-Hall analysis of X-ray diffraction results shows that strain disorder is induced by these applied external stimuli. We show evidence that the structural emergence of domains can provide transfer pathways for holes to a hole transport layer with positive bias. Our findings point to potential origins of I-V hysteresis in halide perovskite solar cells.
ABSTRACT
Hybrid halide perovskite is one of the promising light absorber and is intensively investigated for many optoelectronic applications. Here, the first prototype of a self-powered inorganic halides perovskite for chemical gas sensing at room temperature under visible-light irradiation is presented. These devices consist of porous network of CsPbBr3 (CPB) and can generate an open-circuit voltage of 0.87 V under visible-light irradiation, which can be used to detect various concentrations of O2 and parts per million concentrations of medically relevant volatile organic compounds such as acetone and ethanol with very quick response and recovery time. It is observed that O2 gas can passivate the surface trap sites in CPB and the ambipolar charge transport in the perovskite layer results in a distinct sensing mechanism compared with established semiconductors with symmetric electrical response to both oxidizing and reducing gases. The platform of CPB-based gas sensor provides new insights for the emerging area of wearable sensors for personalized and preventive medicine.