In-air experimental achievement of high-voltage DC power supply to be installed in a tandem electrostatic accelerator system for boron neutron capture therapy application.

The boron neutron capture therapy (BNCT) system developed by the Korea Institute of Radiological and Medical Sciences is a compact neutron source that can be installed at medical institutes. The target energy was accelerated to a maximum of 2.4 MeV-20 mA by introducing a gas stripping device that converts negative hydrogen ions into positive ions. By using the tandem-type accelerator in this way, a high-voltage DC power supply was designed with 1.2 MV-45 mA as the maximum capability. The design was improved to reduce the number of stages of a Cockcroft-Walton voltage multiplier. Hence, the ripple risk of the DC flat top resulting from unwanted stray capacitance was lowered. The overall height and volume of the Cockcroft-Walton voltage multiplier were reduced to less than half those of the existing design method, making miniaturization possible. After such advanced design and manufacturing, performance tests were performed at 750 kV-45 mA under 23 stages of the Cockcroft-Walton voltage multiplier, which is the highest level that can perform at its maximum under in-air conditions. It demonstrated stable performance under in-air conditions without breakdown for 2 h, even at 620 kV-35 mA. To reach the final target of 1.2 MV-45 mA, the groundwork is laid for achieving experimental performance while satisfying the optimal requirements in SF6 gas.

Optimal design of high-voltage DC power supply of 1.2 MV/45 mA applied to boron neutron capture therapy system.

To build a proton beam accelerator that can be applied to a boron neutron capture therapy system based on an electrostatic accelerator, a high-voltage direct-current (DC) power supply system equivalent to the generation of neutrons should be provided. The symmetrical Cockcroft-Walton voltage multiplier method is suitable for stable acceleration of the proton beam in the tandem electrostatic accelerator in this system. Before the second step-up with the Cockcroft-Walton circuit, the design of the inverter is prioritized by preponderantly considering the first voltage and resonance frequency. Moreover, the optimized stacking number is determined with consideration of the ripple voltage, voltage drop, average output voltage, and fundamental harmonics, and a design is performed to set related parameter values to be stable in the flat-top region of the voltage. A high-voltage DC power supply system of 1.2 MV/45 mA is needed for a stable terminal energy of 2.4 MeV/20 mA. Such a design can be optimized by securing reliable data using a simulation tool on the basis of theoretical calculations. This will become a formidable touchstone in manufacturing technology based on acquiring practical know-how for setting up a tandem electrostatic accelerator-based boron neutron capture therapy system in the future.

Performance of an impedance-variable pulsed high-power electron-beam accelerator based on energy efficient transmission.

Versatile high-power pulsed electron-beam accelerators that meet the requirements of pulsed high-power specifications are needed for appropriate applications in medical industry, defense, and other industries. The pulsed electron beam accelerator comprising a Marx generator and Blumlein pulse forming line (PFL) is designed to accelerate the electron beams at the level of 1 MeV when electrostatically discharging. The performance specifications of Marx generators consisting of a 100 kV DC power supply, R-L-C circuit, and high voltage switch are at a maximum 800 kV. At this time, by using the capacitance mismatching principle between the Marx generator and the Blumlein PFL under the law of preserving the amount of charge, it is possible to generate a high voltage in the form of a square pulse up to about 1.1 MV, as much as 1.37 times the charged voltage of the Marx generator. As a result, energy transmission from the Marx generator with a high efficiency of about 85% to the Blumlein PFL is possible. The aim of this study is that the pulsed high-power electron-beam accelerator can be used to change the diode impedance, and the energy of the accelerated electron beam reaches a level of 1 MeV with the square pulse width of about 100 ns at the flat-top in the range of relativistic electron beam generation. Performance tests were securely carried out by installing a dummy load based on CuSO4 solution varying the diode impedance to deter damage to the circuit by preventing reflected waves from being generated in the load.

Experimental study of an initially pressurized water target irradiated by a proton beam.

This experimental visualization study was conducted to investigate and define the phenomena of an initially pressurized liquid water target that can prevent the boiling of water when the target is irradiated with a 30-MeV proton beam produced using the MC-50 Cyclotron at Korea Institute of Radiological and Medical Sciences. At various initial pressures and proton beam currents, the behavior of the target water was investigated using a complementary metal-oxide-semiconductor camera. We confirmed that an appropriate initial pressure could indeed prevent local bulk boiling, and be determined by solving Rayleigh's equation and the Clausius-Clapeyron equation for homogeneous bubble growth using the measured bubble size generated at the Bragg-peak region. The saturation temperature of the initial pressure must be higher than the calculated local water temperature at the Bragg-peak region. The final pressure of the water target increased proportionally with the initial pressure and proton beam current. The penetration depth of the beam varied with beam current and slightly with the final pressure, as evidenced by the emission of blue light in all experimental cases.

Pressure control of a proton beam-irradiated water target through an internal flow channel-induced thermosyphon.

A water target was designed to enhance cooling efficiency using a thermosyphon, which is a system that uses natural convection to induce heat exchange. Two water targets were fabricated: a square target without any flow channel and a target with a flow channel design to induce a thermosyphon mechanism. These two targets had the same internal volume of 8 ml. First, visualization experiments were performed to observe the internal flow by natural convection. Subsequently, an experiment was conducted to compare the cooling performance of both water targets by measuring the temperature and pressure. A 30-MeV proton beam with a beam current of 20 µA was used to irradiate both targets. Consequently, the target with an internal flow channel had a lower mean temperature and a 50% pressure drop compared to the target without a flow channel during proton beam irradiation.