ABSTRACT
Human joints support us to reduce the impact on our body and move them smoothly. As they are composed of gel-like structures, gel materials with soft and resilient properties are expected, as lubricants, to provide high efficiency and a long lifetime for mechanical parts. While double network gels including ionic liquids as swelling agents possess high mechanical strength and stable low friction under high temperature or vacuum, their fabrication process is complex and time-consuming. In this study, we applied one-pot synthesis to a double network ion gel (DNIG) to obtain a thin gel film by a simple coating method and examined its thermal, mechanical and tribological properties. The DNIG was obtained by one-pot synthesis (DNIG-1) combining polycondensation of tetraethoxysilane and radical polymerization of methyl methacrylate to form silica and poly(methyl methacrylate) as a 1st and 2nd network, respectively. Such obtained DNIG-1 was characterized and compared with DNIG obtained by a conventional two-step process (DNIG-2). Thermogravimetric analysis and the compressive stress-strain test showed high thermal stability and mechanical strength of DNIG-1. As friction at the glass/DNIG-1 interface showed high friction compared with that at glass/DNIG-2, various counterface materials were applied to examine their effect on the friction of DNIG-1. As SUS304/DNIG-1 showed much lower friction compared with glass/DNIG-1, the difference in the friction was presumably due to the different adsorption forces and compatibility between the materials.
ABSTRACT
In this paper, in situ surface-initiated atom-transfer radical polymerization (SI-ATRP) based on both an open and a coated system, without using volatile reagents, was developed to overcome the limited usage of ATRP due to the necessity of sealing. Nonvolatile ionic liquid (IL)-type components were used, specifically N,N-diethyl-N-(2-methacryloylethyl)-N-methylammonium bis(trifluoromethylsulfonyl)imide as the polymerizable monomer and N,N-diethylmethyl(2-methoxyethyl)ammonium bis(trifluoromethylsulfonyl)imide as the polymerization solvent. In the experiment, the reversible-deactivation radical polymerization characteristics are properly ensured in nonvolatile ATRP solution coated on silicon wafer as thin liquid film, to form concentrated polymer brushes (CPBs). The average molecular weight and molecular-weight distribution of the polymer produced in the liquid film and formed on silicon wafer were measured by gel permeation chromatography, which confirms that the polymerization reaction occurred as designed. Furthermore, it is clarified that the surface of the polymer brush synthesized in situ swollen by IL also exhibited low friction characteristics, comparable to that synthesized in a typical immersion process. This paper is the first to establish the effectiveness of in situ preparation for CPBs by using the coating technique.
ABSTRACT
A polymerizable ionic liquid, N,N-diethyl-N-(2-methacryloylethyl)-N-methylammonium bis(trifluoromethylsulfonyl)imide (DEMM-TFSI), was polymerized via copper-mediated atom transfer radical polymerization (ATRP). The polymerization proceeded in a living manner producing well-defined poly(DEMM-TFSI) of target molecular weight up to about 400 K (including a polycation and an counter anion). The accurate molecular weight as determined by a GPC analysis combined with a light scattering measurement, and the molecular weight values obtained exhibited good agreement with the theoretical values calculated from the initial molar ratio of DEMM-TFSI and the monomer conversion. Surface-initiated ATRP on the surface of monodisperse silica particles (SiPs) with various diameters was successfully performed, producing SiPs grafted with well-defined poly(DEMM-TFSI) with a graft density as high as 0.15 chains/nm². Since the composite film made from the silica-particle-decorated polymer brush and ionic liquid shows a relatively high ionic conductivity, we have evaluated the relationship between the grafted brush chain length and the ionic conductivity.
ABSTRACT
To evaluate the friction properties of new lubrication systems, two types of ammonium-based ionic liquids (ILs), N,N-diethyl-N-methyl-N-(2-methoxyethyl) ammonium tetrafluoroborate ([DEME][BF4]) and N,N-diethyl-N-methyl-N-(2-methoxyethyl) ammonium bis(trifluoromethanesulfonyl) imide ([DEME][TFSI]), were investigated by resonance shear measurements (RSM) and reciprocating type tribotests between silica (glass) surfaces. RSM revealed that an IL layer of ca. 2 nm in thickness was maintained between the silica surfaces under an applied load of 0.40 mN â¼ 1.2 mN. The relative intensity of the RMS signal indicated that the friction of the system was lower for [DEME][BF4], 0.12, than that of [DEME][TFSI], 0.18. On the other hand, the friction coefficients µk obtained from the tribotests of [DEME][BF4] were lower than that of [DEME][TFSI] for sliding velocities in the range of 5.0 × 10(-4) m s(-1) to 3.0 × 10(-2) m s(-1) under applied loads of 196-980 mN. The friction coefficients obtained by the tribotest are discussed with reference to the RSM results.