Evaluation of centrifugal blood pump performances for biventricular support in the virtual simulation model.

BACKGROUND: Despite the advances in the left ventricular assist device (LVAD), there are still situations that require a biventricular assist device (BVAD) system. The purpose of this study was to explore and compare the system performance interactions with the HeartMate3 (HM3) and HeartWare (HVAD) in a BVAD configuration using the virtual mock loop (VML) simulation tool. METHODS: The VML simulation tool is an in silico implementation of a lumped parameter model of the cardiovascular system with mechanical circulatory support. Patients with ejection fractions of 60%, 20%, and 15% were simulated in VML, and the HVAD and HM3 in a BVAD with ventricular cannulation were applied to simulated conditions. Pump speeds that restored baseline normal hemodynamics were determined. To determine the optimal speeds for BVAD, the left and right arterial pressures (LAP, RAP) were plotted. RESULTS: In the HVAD, LAP and RAP are balanced at 11 mm Hg with LVAD 3500 rpm, right ventricular assist device (RVAD) 2200 rpm; at 13 mm Hg with LVAD 3000 rpm, RVAD 1700 rpm; and at 14 mm Hg with LVAD 2500 rpm, RVAD 1300 rpm. For the HM3, at 8 mm Hg with LVAD 7000 rpm, RVAD 5000 rpm; at 9 mm Hg with LVAD 6000 rpm, RVAD 4300 rpm; and at 9.5 mm Hg with LVAD 5000 rpm, RVAD 3500 rpm. CONCLUSION: The RVAD/LVAD speed ratios required for atrial balance were approximately 0.6 for the HVAD and 0.7 for the HM3. However, the HVAD required RVAD speeds below its range of operation.

Left Atrial Circulatory Assistance in Simulated Diastolic Heart Failure Model: First in Vitro and in Vivo.

BACKGROUND: We are developing a left atrial assist device (LAAD) that is implanted at the mitral position to treat diastolic heart failure (DHF) represented by heart failure with preserved ejection fraction. METHODS: The LAAD was tested at 3 pump speeds on a pulsatile mock loop with a pneumatic pump that simulated DHF conditions by adjusting the diastolic drive. The LAAD was implanted in 6 calves, and the hemodynamics were assessed. In 3 cases, DHF conditions were induced by using a balloon inserted into the left ventricle, and in 2 cases, mitral valve replacement was also performed after the second aortic cross-clamp. RESULTS: DHF conditions were successfully induced in the in vitro study. With LAAD support, cardiac output, aortic pressure and left atrial pressure recovered to normal values, whereas pulsatility was maintained for both in vivo and in vitro studies. Echocardiography showed no left ventricular outflow tract obstruction, and the LAAD was successfully replaced by a mechanical prosthetic valve. CONCLUSIONS: These initial in vitro and in vivo results support our hypothesis that use of the LAAD increases cardiac output and aortic pressure and decreases left atrial pressure, while maintaining arterial pulsatility.

Computational Fluid Dynamics Model of Continuous-Flow Total Artificial Heart: Right Pump Impeller Design Changes to Improve Biocompatibility.

Cleveland Clinic is developing a continuous-flow total artificial heart (CFTAH). This novel design operates without valves and is suspended both axially and radially through the balancing of the magnetic and hydrodynamic forces. A series of long-term animal studies with no anticoagulation demonstrated good biocompatibility, without any thromboemboli or infarctions in the organs. However, we observed varying degrees of thrombus attached to the right impeller blades following device explant. No thrombus was found attached to the left impeller blades. The goals for this study were: (1) to use computational fluid dynamics (CFD) to gain insight into the differences in the flow fields surrounding both impellers, and (2) to leverage that knowledge in identifying an improved next-generation right impeller design that could reduce the potential for thrombus formation. Transient CFD simulations of the CFTAH at a blood flow rate and impeller rotational speed mimicking in vivo conditions revealed significant blade tip-induced flow separation and clustered regions of low wall shear stress near the right impeller that were not present for the left impeller. Numerous right impeller design variations were modeled, including changes to the impeller cone angle, number of blades, blade pattern, blade shape, and inlet housing design. The preferred, next-generation right impeller design incorporated a steeper cone angle, a primary/splitter blade design similar to the left impeller, and an increased blade curvature to better align the incoming flow with the impeller blade tips. The next-generation impeller design reduced both the extent of low shear regions near the right impeller surface and flow separation from the blade leading edges, while maintaining the desired hydraulic performance of the original CFTAH design.

Total Artificial Heart Computational Fluid Dynamics: Modeling of Stator Bore Design Effects on Journal-Bearing Performance.

Cleveland Clinic's continuous-flow total artificial heart (CFTAH) is a double-ended centrifugal blood pump that has a single rotating assembly with an embedded magnet, which is axially and radially suspended by a balance of magnetic and hydrodynamic forces. The key to the radial suspension is a radial offset between the stator bearing bore and the magnet's steel laminations. This offset applies a radial magnetic force, which is balanced by a hydrodynamic force as the rotating assembly moves to a "force-balanced" radial position. The journal-bearing blood passage is a narrow flow path between the left and right impellers. The intent of this study was to determine the impact of the stator-bearing bore radius on the journal-bearing hydraulic performance while satisfying the geometric design constraints imposed by the pump and motor configuration. Electromagnetic forces on the journal bearing were calculated using the ANSYS EMAG program, Version 18 (ANSYS, Canonsburg, PA). ANSYS CFX Version 19.2 was then used to model the journal-bearing flow paths of the most recent design of the CFTAH. A transient, moving mesh approach was used to locate the steady state, force-balanced position of the rotating assembly. The blood was modeled as a non-Newtonian fluid. The computational fluid dynamics simulations showed that by increasing stator bore radius, rotor power, stator wall average shear stress, and blood residence time in journal-bearing decrease, while blood net flow rate through the bearing increases. The results were used to select a new bearing design that provides an improved performance compared with the baseline design. The performance of the new CFTAH-bearing design will be confirmed through upcoming in vitro and in vivo testing.

Characterization and Development of Universal Ventricular Assist Device: Computational Fluid Dynamics Analysis of Advanced Design.

We are developing a universal, advanced ventricular assist device (AVAD) with automatic pressure regulation suitable for both left and right ventricular support. The primary goal of this computational fluid dynamics (CFD) study was to analyze the biventricular performance of the AVAD across its wide range of operating conditions. An AVAD CFD model was created and validated using in vitro hydraulic performance measurements taken over conditions spanning both left ventricular assist device (LVAD) and right ventricular assist device (RVAD) operation. Static pressure taps, placed throughout the pump, were used to validate the CFD results. The CFD model was then used to assess the change in hydraulic performance with varying rotor axial positions and identify potential design improvements. The hydraulic performance was simulated and measured at rotor speeds from 2,300 to 3,600 revolutions/min and flow rates from 2.0 to 8.0 L/min. The CFD-predicted hydraulic pressure rise agreed well with the in vitro measured data, within 6.5% at 2300 rpm and within 3.5% for the higher rotor speeds. The CFD successfully predicted wall static pressures, matching experimental values within 7%. High degree of similarity and circumferential uniformity in the pump's flow fields were observed over the pump operation as an LVAD and an RVAD. A secondary impeller axial clearance reduction resulted in a 10% decrease in peak flow residence time and lower static pressures on the secondary impeller. These lower static pressures suggest a reduction in the upwards rotor forces from the secondary impeller and a desired increase in the pressure sensitivity of the pump. The CFD analyses supported the feasibility of the proposed AVAD's use as an LVAD or an RVAD, over a wide range of operating conditions. The CFD results demonstrated the operability of the pump in providing the desired circumferential flow similarity over the intended range of flow/speed conditions and the intended functionality of the AVAD's automated pressure regulation.

Left atrial assist device to treat patients with heart failure with preserved ejection fraction: Initial in vitro study.

OBJECTIVES: Many patients with heart failure have preserved ejection fraction but also diastolic dysfunction, with no effective therapy. We are developing a new pump (left atrial assist device, LAAD) for implantation at the mitral position to pump blood from the left atrium to sufficiently fill the left ventricle. The purpose of the initial in vitro study was to demonstrate that the LAAD can reduce left atrial pressure (LAP) and increase cardiac output (CO) while maintaining arterial pulsatility and normal aortic valve function using a proof-of-concept device. METHODS: The LAAD concept was tested at 3 pump speeds on a pulsatile mock loop with a pneumatic pump that simulated the normal function of the native ventricle as well as 3 levels of diastolic heart failure (DHF 1, 2, and 3) by adjusting the diastolic drive pressure to limit diastolic filling of the ventricle. RESULTS: Without the LAAD, CO and aortic pressure (AoP) decreased dramatically from 3.8 L/min and 100 mm Hg at normal heart condition to 1.2 L/min and 35 mm Hg at DHF 3, respectively. With LAAD support, both CO and AoP recovered to normal heart values at 3200 rpm and surpassed normal heart values at 3800 rpm. Furthermore, with LAAD support, LAP recovered to almost that of the normal heart condition at 3800 rpm. CONCLUSIONS: These initial in vitro results support our hypothesis that use of the LAAD increases CO and AoP and decreases LAP under DHF conditions while maintaining arterial pulsatility and full function of the aortic valve.

The Effects of Preserving Mitral Valve Function on a Left Atrial Assist Device: An In Vitro Mock Circulation Loop Study.

We are developing a left atrial assist device (LAAD) to pump blood from the left atrium to the left ventricle for patients who have heart failure with preserved ejection fraction (HFpEF). This study aimed to assess the hemodynamics with the LAAD implanted at two different levels: the mitral valve (MV) level, after removing the MV; and the supravalvular level, preserving MV function conditions using an in vitro mock circulatory loop. Normal heart and mild, moderate, and severe diastolic heart failure conditions were simulated, and the LAAD was set at three different speeds. Without the LAAD support, cardiac output (CO) decreased from 3.7 to 1.1 L/min, aortic pressure (AoP) decreased from 100 to 33 mm Hg, and left atrial pressure (LAP) increased from 16 to 23 mm Hg as the diastolic function became impaired. With high pump support after removing the MV, CO and AoP readings were comparable with those for preserved MV function (CO reached 3.9-4.1 L/min, AoP reached more than 110 mm Hg, and LAP dropped to 16-17 mm Hg under both conditions at high pump speeds). In the mock circulatory loop, our LAAD appeared to have sufficient ability to maintain the hemodynamic status at both positions.

Left atrial assist device function at various heart rates using a mock circulation loop.

We are developing a new left atrial assist device (LAAD) for patients who have heart failure with preserved ejection fraction (HFpEF). This study aimed to assess the hemodynamic effects of the LAAD under both normal heart conditions and various diastolic heart failure (DHF) conditions using a mock circulatory loop. A continuous-flow pump that simulates LAAD, was placed between the left atrial (LA) reservoir and a pneumatic ventricle that simulated a native left ventricle on a pulsatile mock loop. Normal heart (NH) and mild, moderate, and severe DHF conditions were simulated by adjusting the diastolic drive pressures of the pneumatic ventricle. With the LAAD running at 3200 rpm, data were collected at 60, 80, and 120 bpm of the pneumatic ventricle. Cardiac output (CO), mean aortic pressure (AoP), and mean LA pressure (LAP) were compared to evaluate the LAAD performance. With LAAD support, the CO and AoP rose to a sufficient level at all heart rates and DHF conditions (CO; 3.4-3.8 L/min, AoP; 90-105 mm Hg). Each difference in the CO and the AoP among various heart rates was minuscule compared with non-pump support. The LAP decreased from 21-23 to 17-19 mm Hg in all DHF conditions (difference not significant). Furthermore, hemodynamic parameters improved for all DHF conditions, independent of heart rate. The LAAD can provide adequate flow to maintain the circulation status at various heart rates in an in vitro mock circulatory loop.

Modeling of Virtual Mechanical Circulatory Hemodynamics for Biventricular Heart Failure Support.

OBJECTIVE: In this study, a mechanical circulatory support simulation tool was used to investigate the application of a unique device with two centrifugal pumps and one motor for the biventricular assist device (BVAD) support application. Several conditions-including a range of combined left and right systolic heart failure severities, aortic and pulmonary valve regurgitation, and combinations of high and low systemic and pulmonary vascular resistances-were considered in the simulation matrix. Relative advantages and limitations of using the device in BVAD applications are discussed. METHODS: The simulated BVAD pump was based on the Cleveland Clinic pediatric continuous-flow total artificial heart (P-CFTAH), which is currently under development. Different combined disease states (n = 10) were evaluated to model the interaction with the BVAD, considering combinations of normal heart, moderate failure and severe systolic failure of the left and right ventricles, regurgitation of the aortic and pulmonary valves and combinations of vascular resistance. The virtual mock loop simulation tool (MATLAB; MathWorks®, Natick, MA) simulates the hemodynamics at the pump ports using a lumped-parameter model for systemic/pulmonary circulation characteristic inputs (values for impedance, systolic and diastolic ventricular compliance, beat rate, and blood volume), and characteristics of the cardiac chambers and valves. RESULTS: Simulation results showed that this single-pump BVAD can provide regulated support of up to 5 L/min over a range of combined heart failure states and is suitable for smaller adult and pediatric support. However, good self-regulation of the atrial pressure difference was not maintained with the introduction of aortic valve regurgitation or high systemic vascular resistance when combined with low pulmonary vascular resistance. CONCLUSIONS: This initial in silico study demonstrated that use of the P-CFTAH as a BVAD supports cardiac output and arterial pressure in biventricular heart failure conditions. A similar but larger device would be required for a large adult patient who needs more than 5 L/min of support.

Anti-clogging mechanisms of a motion-activated chest tube patency maintenance system: Histology and high-speed camera assessment.

The motion-activated system (MAS) employs vibration to prevent intraluminal chest tube clogging. We evaluated the intraluminal clot formation inside chest tubes using high-speed camera imaging and postexplant histology analysis of thrombus. The chest tube clogging was tested (MAS vs. control) in acute hemothorax porcine models (n = 5). The whole tubes with blood clots were fixed with formalin-acetic acid solution and cut into cross-sections, proceeded for H&E-stained paraffin-embedded tissue sections (MAS sections, n = 11; control sections, n = 11), and analyzed. As a separate effort, a high-speed camera (FASTCAM Mini AX200, 100-mm Zeiss lens) was used to visualize the whole blood clogging pattern inside the chest tube cross-sectional view. Histology revealed a thin string-like fibrin deposition, which showed spiral eddy or aggregate within the blood clots in most sections of Group MAS, but not in those of the control group. Histology findings were compatible with high-speed camera views. The high-speed camera images showed a device-specific intraluminal blood "swirling" pattern. Our findings suggest that a continuous spiral flow in blood within the chest tube (MAS vs. static control) contributes to the formation of a spiral string-like fibrin network during consumption of coagulation factors. As a result, the spiral flow may prevent formation of thick band-like fibrin deposits sticking to the inner tube surface and causing tube clogging, and thus may positively affect chest tube patency and drainage.

First In Vivo Experience With Biventricular Circulatory Assistance Using a Single Continuous Flow Pump.

Biventricular assist device (BVAD) implantation is the treatment of choice in patients with severe biventricular heart failure and cardiogenic shock. Our team has developed a miniaturized continuous flow, double-ended centrifugal pump intended for total artificial heart implant (CFTAH). The purpose of this initial in vivo study was to demonstrate that the scaled-down CFTAH (P-CFTAH) can be appropriate for BVAD support. The P-CFTAH was implanted in 4 acute lambs (average weight, 41.5 ± 2.8 kg) through a median sternotomy. The cannulation was performed through the left and right atria, and cannulae length adjustment was performed for atrial and ventricular cannulation. The BVAD system was tested at 3 pump speeds (3000, 4500, and 6000 rpm). The BVAD performed very well for both atrial and ventricular cannulation within the 3000-6000 rpm range. Stable hemodynamics were maintained after implantation of the P-CFTAH. The self-regulating performance of the system in vivo was demonstrated by the left (LAP) and right (RAP) pressure difference (LAP-RAP) falling predominantly within the range of -5 to 10 mm Hg with variation, in addition to in vitro assessment of left and right heart failure conditions. Left and right pump flows and total flow increased as the BVAD speed was increased. This initial in vivo testing of the BVAD system demonstrated satisfactory device performance and self-regulation for biventricular heart failure support over a wide range of conditions. The BVAD system keeps the atrial pressure difference within bounds and maintains acceptable cardiac output over a wide range of hemodynamic conditions.

Effects of blood pump orientation on performance: In vitro assessment of universal advanced ventricular assist device.

An advanced ventricular assist device (VAD), which is under development in our institution, has specific features that allow changes in the axial rotor position and pump performance by intrapump pressure difference. However, performance could be influenced by the pump orientation because of the effect of gravity on the rotor position. The purpose of this study was to evaluate the effects of pump orientation on the pump performance, including pulse pressure and regurgitant flow through the pump when the pump was stopped. Bench testing of the VAD was performed on a static or pulsatile mock loop with a pneumatic device to simulate the native ventricle. The pump performance, including pressure-flow curve, pulsatility, and regurgitant flow, was evaluated at several angles, ranging from -90° (inlet pointed upward) to +90° (inlet pointed downward) at pump speeds of 2000, 2500, 3000, and 3500 rpm. The pump performance was slightly lower at +90° at all rotational speeds, compared with -90°. The pulse pressure on the pulsatile mock loop (80 bpm) was 50 mm Hg without pump support, remained at 50 mm Hg during pump support, and was not changed by orientation (-90°, 0°, and +90°). When the pump was stopped, the regurgitant flow was near 0 L/min at all angles. Pump orientation had a minor effect on pump performance, with no effect on pulse pressure or regurgitant flow when the pump was stopped. This indicates that the effect of gravity on the rotor assembly is insignificant.

A simulation tool for mechanical circulatory support device interaction with diseased states.

We have created a simulation model to investigate the interactions between a variety of mechanical circulatory support (MCS) devices and the circulatory system with various simulated patient conditions and disease states. The present simulation accommodates a family of continuous-flow MCS devices under various stages of consideration or development at our institution. This article describes the mathematical core of the in silico simulation system and shows examples of simulation output imitating various disease states and of selected in vitro and clinical data from the literature.

Use of a Virtual Mock Loop model to evaluate a new left ventricular assist device for transapical insertion.

We are developing a novel type of miniaturized left ventricular assist device that is configured for transapical insertion. The aim of this study was to assess the performance and function of a new pump by using a Virtual Mock Loop system for device characterization and mapping. The results, such as pressure-flow performance curves, from pump testing in a physical mock circulatory loop were used to analyze its function as a left ventricular assist device. The Virtual Mock Loop system was programmed to mimic the normal heart condition, systolic heart failure, diastolic heart failure, and both systolic and diastolic heart failure, and to provide hemodynamic pressure values before and after the activation of several left ventricular assist device pump speeds (12,000, 14,000, and 16,000 r/min). With pump support, systemic flow and mean aortic pressure increased, and mean left atrial pressure and pulmonary artery pressure decreased for all heart conditions. Regarding high pump-speed support, the systemic flow, aortic pressure, left atrial pressure, and pulmonary artery pressure returned to the level of the normal heart condition. Based on the test results from the Virtual Mock Loop system, the new left ventricular assist device for transapical insertion may be able to ease the symptoms of patients with various types of heart failure. The Virtual Mock Loop system could be helpful to assess pump performance before in vitro bench testing.

Development of a circulatory mock loop for biventricular device testing with various heart conditions.

This study aimed to evaluate a newly designed circulatory mock loop intended to model cardiac and circulatory hemodynamics for mechanical circulatory support device testing. The mock loop was built with dedicated ports suitable for attaching assist devices in various configurations. This biventricular mock loop uses two pneumatic pumps (Abiomed AB5000™, Danvers, MA, USA) driven by a dual-output driver (Thoratec Model 2600, Pleasanton, CA, USA). The drive pressures can be individually modified to simulate a healthy heart and left and/or right heart failure conditions, and variable compliance and fluid volume allow for additional customization. The loop output for a healthy heart was tested at 4.2 L/min with left and right atrial pressures of 1 and 5 mm Hg, respectively; a mean aortic pressure of 93 mm Hg; and pulmonary artery pressure of 17 mm Hg. Under conditions of left heart failure, these values were reduced to 2.1 L/min output, left atrial pressure = 28 mm Hg, right atrial pressure = 3 mm Hg, aortic pressure = 58 mm Hg, and pulmonary artery pressure = 35 mm Hg. Right heart failure resulted in the reverse balance: left atrial pressure = 0 mm Hg, right atrial pressure = 30 mm Hg, aortic pressure = 100 mm Hg, and pulmonary artery pressure = 13 mm Hg with a flow of 3.9 L/min. For biventricular heart failure, flow was decreased to 1.6 L/min, left atrial pressure = 13 mm Hg, right atrial pressure = 13 mm Hg, aortic pressure = 52 mm Hg, and pulmonary artery pressure = 18 mm Hg. This mock loop could become a reliable bench tool to simulate a range of heart failure conditions.

An advanced universal circulatory assist device for left and right ventricular support: First report of an acute in vivo implant.

Background: The Advanced ventricular assist device (Advanced VAD) is designed as a universal pump intended to prevent backflow in the event of pump stoppage, to maintain physiological pulse pressure, and to be used as both a left and right VAD. The purpose of this study was to evaluate the performance of the Advanced VAD as both a left and right VAD in an acute in vivo study in calves. Methods: The Advanced VAD was implanted through a median sternotomy in 5 healthy calves (weight, 71.4-91.2 kg) as a left VAD (n = 3) or a right VAD (n = 2). After implantation, hemodynamic parameters, including general performance and pump stoppage, were evaluated. Results: The Advanced VAD was successfully implanted as a left and right VAD without cardiopulmonary bypass. The speed range of the Advanced VAD was 2500 to 3500 rpm as a left VAD and 2000 to 2500 rpm as a right VAD. Up to 4.3 L/min was achieved for both left and right VAD configurations. To demonstrate the automatic shut-off feature, the pump was stopped without clamping the outflow graft. The outflow graft was then clamped, which produced no significant changes in the arterial pressure waveform. The pulse pressures under the left VAD configuration were 38 mm Hg, 17 mm Hg, 14 mm Hg, and 16 mm Hg at baseline, 2500 rpm, 3000 rpm, and 3500 rpm, respectively. Conclusions: This acute in vivo study demonstrated the pump performance, anatomical fitting as both left VAD and right VAD, and regurgitant flow shut-off feature of the Advanced VAD.

Analysis of Cleveland Clinic continuous-flow total artificial heart performance using the Virtual Mock Loop: Comparison with an in vivo study.

The Virtual Mock Loop (VML) is a mathematical model designed to simulate mechanism of the human cardiovascular system interacting with mechanical circulatory support devices. Here, we aimed to mimic the hemodynamic performance of Cleveland Clinic's self-regulating continuous-flow total artificial heart (CFTAH) via VML and evaluate the accuracy of the VML compared with an in vivo acute animal study. The VML reproduced 124 hemodynamic conditions from three acute in vivo experiments in calves. Systemic/pulmonary vascular resistances, pump rotational speed, pulsatility, and pulse rate were set for the VML from in vivo data. We compared outputs (pump flow, left and right pump pressure rises, and atrial pressure difference) between the two systems. The pump performance curves all fell in the designed range. There was a strong correlation between the VML and the in vivo study in the left pump flow (r2 = 0.84) and pressure rise (r2 = 0.80), and a moderate correlation in right pressure rise (r2 = 0.52) and atrial pressure difference (r2 = 0.59). Although there is room for improvement in simulating right-sided pump performance of self-regulating CFTAH, the VML acceptably simulated the hemodynamics observed in an in vivo study. These results indicate that pump flow and pressure rise can be estimated from vascular resistances and pump settings.

The design modification of advanced ventricular assist device to enhance pulse augmentation and regurgitant flow shut-off.

The new Advanced ventricular assist device (Advanced VAD) has many features such as improving pulsatility and preventing regurgitant flow during pump stoppage. The purpose of this study was to evaluate the effects of design modifications of the Advanced VAD on these features in vitro. Bench testing of four versions of the Advanced VAD was performed on a static or pulsatile mock loop with a pneumatic device. After pump performance was evaluated, each pump was run at 3000 rpm to evaluate pulse augmentation, then was stopped to assess regurgitant flow through the pump. There was no significant difference in pump performance between the pump models. The average pulse pressure in the pulsatile mock loop was 23.0, 34.0, 39.3, 33.8, and 37.3 mm Hg without pump, with AV010, AV020 3S, AV020 6S, and AV020 RC, respectively. The pulse augmentation factor was 48%, 71%, 47%, and 62% with AV010, AV020 3S, AV020 6S, and AV020 RC, respectively. In the pump stop test, regurgitant flow was -0.60 ± 0.70, -0.13 ± 0.57, -0.14 ± 0.09, and -0.18 ± 0.06 L/min in AV010, AV020 3S, AV020 6S, and AV020 RC, respectively. In conclusion, by modifying the design of the Advanced VAD, we successfully showed the improved pulsatility augmentation and regurgitant flow shut-off features.

Continuous-flow total artificial heart: hemodynamic and pump-related changes associated with posture in a chronic calf model.

This study aimed to evaluate the effects of posture (sitting [lying down]/standing) on hemodynamic and pump-related parameters in calves implanted with our institution's continuous-flow total artificial heart (CFTAH). These parameters were analyzed with posture information in four calves that had achieved the intended 14-, 30-, or 90-day durations of implantation. In each animal, postoperative hourly data gathered throughout the study were used to compare average values with the animal sitting vs. standing. Pump flow became significantly higher in the standing than sitting position at the same pump speed (standing 7.9 ± 0.8, sitting 7.4 ± 1.0 L/min, p = 0.028). Systemic vascular resistance (SVR) and aortic pressure (AoP) were significantly lower in the standing than sitting position (SVR standing 779 ± 145, sitting 929 ± 206 dyne s/cm5, p = 0.027; AoP standing 93 ± 7, sitting 103 ± 7 mm Hg, p < 0.001). No substantial change occurred in pulmonary vascular resistance (PVR) or pulmonary arterial pressure (PAP) with posture (PVR standing 161 ± 39, sitting 164 ± 48 dyne s/cm5, p = 0.639; PAP standing 32 ± 3, sitting 33 ± 4 mm Hg, p = 0.340). Posture affected some hemodynamic and pump-related parameters in calves with CFTAH, with implications for patients with implanted pumps.

Advantages of Integrating Pressure-Regulating Devices Into Mechanical Circulatory Support Pumps.

Control of mechanical circulatory support pump output typically requires that pressure-regulating functions be accomplished by active control of the speed or geometry of the device, with feedback from pressure or flow sensors. This article presents a different design approach, with a pressure-regulating device as the core design feature, allowing the essential control function of regulating pressure to be directly programmed into the hydromechanical design. We show the step-by-step transformation of a pressure-regulating device into a continuous-flow total artificial heart that passively balances left and right circulations without the need for pressure and flow sensors. In addition, we discuss a ventricular assist device that prevents backflow in the event of power interruption and also dynamically interacts with residual ventricle function to preserve pulsatility.