Giant piezoresponse in nanoporous (Ba,Ca)(Ti,Zr)O3 thin film.

Lattice strain effects on the piezoelectric properties of crystalline ferroelectrics have been extensively studied for decades; however, the strain dependence of the piezoelectric properties at nano-level has yet to be investigated. Herein, a new overview of the super-strain of nanoporous polycrystalline ferroelectrics is reported for the first time using a nanoengineered barium calcium zirconium titanate composition (Ba0.85Ca0.15)(Ti0.9Zr0.1)O3 (BCZT). Atomic-level investigations show that the controlled pore wall thickness contributes to highly strained lattice structures that also retain the crystal size at the optimal value (<30 nm), which is the primary contributor to high piezoelectricity. The strain field derived from geometric phase analysis at the atomic level and aberration-corrected high-resolution scanning transmission electron microscopy (STEM) yields of over 30% clearly show theoretical agreement with high piezoelectric properties. The uniqueness of this work is the simplicity of the synthesis; moreover the piezoresponse d 33 becomes giant, at around 7500 pm V-1. This response is an order of magnitude greater than that of lead zirconate titanate (PZT), which is known to be the most successful ferroelectric over the past 50 years. This concept utilizing nanoporous BCZT will be highly useful for a promising high-density electrolyte-free dielectric capacitor and generator for energy harvesting in the future.

A Mesoporous Gold Sensor Unveils Phospho PD-L1 in Extracellular Vesicles as a Proxy for PD-L1 Expression in Lung Cancer Tissue.

Immune checkpoint inhibitors (ICIs) targeting programmed cell death ligand 1 (PD-L1), or its receptor, PD-1 have improved survival in patients with non-small-cell lung cancer (NSCLC). Assessment of PD-L1 expression requires tissue biopsy or fine needle aspiration that are currently used to identify patients most likely to respond to single agent anti-PD-1/PD-L1 therapy. However, obtaining sufficient tissue to generate a PD-L1 tissue proportion score (TPS) ≥ 50% using immunohistochemistry remains a challenge that potentially may be overcome by liquid biopsies. This study utilized a mesoporous gold sensor (MGS) assay to examine the phosphorylation status of PD-L1 in plasma extracellular vesicles (EV pPD-L1) and PD-L1 levels in plasma from NSCLC patient samples and their association with tumor PD-L1 TPS. The 3-dimensional mesoporous network of the electrodes provides a large surface area, high signal-to-noise ratio, and a superior electro-conductive framework, thereby significantly improving the detection sensitivity of PD-L1 nanosensing. Test (n = 20) (Pearson's r = 0.99) and validation (n = 45) (Pearson's r = 0.99) cohorts show that EV pPD-L1 status correlates linearly with the tumor PD-L1 TPS assessed by immunohistochemistry irrespective of the tumor stage, with 64% of patients overall showing detectable EV pPD-L1 levels in plasma. In contrast to the EV pPD-L1 results, plasma PD-L1 levels did not correlate with the tumor PD-L1 TPS score or EV pPD-L1 levels. These data demonstrate that EV pPD-L1 levels may be used to select patients for appropriate PD-1 and PD-L1 ICI therapy regimens in early, locally advanced, and advanced NSCLC and should be tested further in randomized controlled trials. Most importantly, the assay used has a less than 24h turnaround time, facilitating adoption of the test into the routine diagnostic evaluation of patients prior to therapy.

Mesoporous Gold: Substrate-Dependent Growth Dynamics, Strain Accumulation, and Electrocatalytic Activity for Biosensing.

Understanding the growth of mesoporous crystalline materials, such as mesoporous metals, on different substrates can provide valuable insights into the crystal growth dynamics and the redox reactions that influence their electrochemical sensing performance. Herein, it is demonstrated how the amorphous nature of the glass substrate can suppress the typical <111> oriented growth in mesoporous Au (mAu) films. The suppressed <111> growth is manifested as an accumulation of strain, leading to the generation of abundant surface defects, which are beneficial for enhancing the electrochemical activity. The fine structuring attained enables dramatically accelerated diffusion and enhances the electrochemical sensing performance for disease-specific biomolecules. As a proof-of-concept, the as-fabricated glass-grown mAu film demonstrates high sensitivity in electrochemical detection of SARS-CoV-2-specific RNA with a limit of detection (LoD) as low as 1 attomolar (aM).

A mesoporous gold biosensor to investigate immune checkpoint protein heterogeneity in single lung cancer cells.

Immune checkpoint proteins (ICPs) play a major role in a patient's immune response against cancer. Tumour cells usually express those proteins to communicate with immune cells as a process of escaping the anti-cancer immune response. Detecting the major functional immune checkpoint proteins present on cancer cells (such as circulating tumor cells or CTCs) and examining the heterogeneity in their expression at the single-cell level could play a crucial role in both cancer diagnosis and the monitoring of therapy. In this study, we develop a mesoporous gold biosensor to precisely assess ICP heterogeneity in individual cancer cells within a lung cancer model. The platform utilizes a nanostructured mesoporous gold surface to capture CTCs and a Surface Enhanced Raman Scattering (SERS) readout to identify and monitor the expression of key ICP proteins (PD-L1, B7H4, CD276, CD80) in lung cancer cells. The homogeneous and abundant pores in mesoporous 3D gold nanostructures enable increased antibody loading on-chip and an enhanced SERS signal, which are key to our single cell capture, and accurate analysis of ICPs in cancer cells with high sensitivity. Our lung cancer cell line model data showed that our method can detect single cells and analyse the expression of four lung cancer associated ICPs on individual cell surfaces during treatment. To show the potential of our mesoporous gold biosensor in analysing clinical samples, we tested 9 longitudinal Peripheral Blood Mononuclear Cells (PBMC) samples from lung cancer patient before and after therapy. Our mesoporous biosensor successfully captured single CTCs and found that the expression of ICPs in CTCs is highly heterogeneous in both pre-treatment and treated PBMC samples isolated from lung cancer patient blood. We suggest that our findings will help clinicians in selecting the most appropriate therapy for patients.

Au-Loaded Superparamagnetic Mesoporous Bimetallic CoFeB Nanovehicles for Sensitive Autoantibody Detection.

Construction of a well-defined mesoporous nanostructure is crucial for applying nonnoble metals in catalysis and biomedicine owing to their highly exposed active sites and accessible surfaces. However, it remains a great challenge to controllably synthesize superparamagnetic CoFe-based mesoporous nanospheres with tunable compositions and exposed large pores, which are sought for immobilization or adsorption of guest molecules for magnetic capture, isolation, preconcentration, and purification. Herein, a facile assembly strategy of a block copolymer was developed to fabricate a mesoporous CoFeB amorphous alloy with abundant metallic Co/Fe atoms, which served as an ideal scaffold for well-dispersed loading of Au nanoparticles (∼3.1 nm) via the galvanic replacement reaction. The prepared Au-CoFeB possessed high saturation magnetization as well as uniform and large open mesopores (∼12.5 nm), which provided ample accessibility to biomolecules, such as nucleic acids, enzymes, proteins, and antibodies. Through this distinctive combination of superparamagnetism (CoFeB) and biofavorability (Au), the resulting Au-CoFeB was employed as a dispersible nanovehicle for the direct capture and isolation of p53 autoantibody from serum samples. Highly sensitive detection of the autoantibody was achieved with a limit of detection of 0.006 U/mL, which was 50 times lower than that of the conventional p53-ELISA kit-based detection system. Our assay is capable of quantifying differential expression patterns for detecting p53 autoantibodies in ovarian cancer patients. This assay provides a rapid, inexpensive, and portable platform with the potential to detect a wide range of clinically relevant protein biomarkers.

Magnetic Hydrogel Composite for Wastewater Treatment.

Nanocomposite hydrogels are highly porous colloidal structures with a high adsorption capacity, making them promising materials for wastewater treatment. In particular, magnetic nanoparticle (MNP) incorporated hydrogels are an excellent adsorbent for aquatic pollutants. An added advantage is that, with the application of an external magnetic field, magnetic hydrogels can be collected back from the wastewater system. However, magnetic hydrogels are quite brittle and structurally unstable under compact conditions such as in fixed-bed adsorption columns. To address this issue, this study demonstrates a unique hydrogel composite bead structure, providing a good adsorption capacity and superior compressive stress tolerance due to the presence of hollow cores within the beads. The gel beads contain alginate polymer as the matrix and MNP-decorated cellulose nanofibres (CNF) as the reinforcing agent. The MNPs within the gel provide active adsorption functionality, while CNF provide a good stress transfer phenomenon when the beads are under compressive stress. Their adsorption performance is evaluated in a red mud solution for pollutant adsorption. Composite gel beads have shown high performance in adsorbing metal (aluminium, potassium, selenium, sodium, and vanadium) and non-metal (sulphur) contaminations. This novel hybrid hydrogel could be a promising alternative to the conventionally used toxic adsorbent, providing environmentally friendly operational benefits.

Hydrogel Nanoarchitectonics: An Evolving Paradigm for Ultrasensitive Biosensing.

The integration of nanoarchitectonics and hydrogel into conventional biosensing platforms offers the opportunities to design physically and chemically controlled and optimized soft structures with superior biocompatibility, better immobilization of biomolecules, and specific and sensitive biosensor design. The physical and chemical properties of 3D hydrogel structures can be modified by integrating with nanostructures. Such modifications can enhance their responsiveness to mechanical, optical, thermal, magnetic, and electric stimuli, which in turn can enhance the practicality of biosensors in clinical settings. This review describes the synthesis and kinetics of gel networks and exploitation of nanostructure-integrated hydrogels in biosensing. With an emphasis on different integration strategies of hydrogel with nanostructures, this review highlights the importance of hydrogel nanostructures as one of the most favorable candidates for developing ultrasensitive biosensors. Moreover, hydrogel nanoarchitectonics are also portrayed as a promising candidate for fabricating next-generation robust biosensors.

Recent progress of functional metal-organic framework materials for water treatment using sulfate radicals.

Human health is being threatened by the ever-increasing water pollution. Sulfate radical (SO4•-)-based advanced oxidation processes (SR-AOPs) are rapidly being developed and gaining considerable attention due to their high oxidation potential and selectivity as a way to purify water by degrading organic contaminants in it. Among the catalytic materials that can activate the precursor to generate SO4•-, metal-organic frameworks (MOFs) are the most promising heterogeneous catalytic material in SR-AOPs because of their various structure possibilities, large surface area, ordered porous structure, and regular activation sites. Herein, an in-depth overview of MOFs and their derivatives for water purification with SR-AOPs is provided. The latest studies on pristine MOFs, MOF composites, and MOF derivatives (metal oxides, metal-carbon hybrids, and carbon materials) are summarized. The mechanisms of decomposition of pollutants in water via radical and non-radical pathways are also discussed. This review suggests future research directions for water purification through MOF-based SR-AOP.

Cu-based MOF-derived architecture with Cu/Cu2O nanospheres anchored on porous carbon nanosheets for efficient capacitive deionization.

The design of high-performance electrode materials with excellent desalination ability has always been a research goal for efficient capacitive deionization (CDI). Herein, a hybrid architecture with Cu/Cu2O nanospheres anchored on porous carbon nanosheets (Cu/Cu2O/C) was first synthesized by pyrolyzing a two-dimensional (2D) Cu-based metal-organic framework and then evaluated as a cathode for hybrid CDI. The as-prepared Cu/Cu2O/C exhibits a hierarchically porous structure with a high specific surface area of 305 m2 g-1 and large pore volume of 0.55 cm3 g-1, which is favorable to accelerating ion migration and diffusion. The porous carbon nanosheet matrix with enhanced conductivity will facilitate the Faradaic reactions of Cu/Cu2O nanospheres during the desalination process. The Cu/Cu2O/C hybrid architecture displays a high specific capacitance of 142.5 F g-1 at a scan rate of 2 mV s-1 in 1 M NaCl solution. The hybrid CDI constructed using the Cu/Cu2O/C cathode and a commercial activated carbon anode exhibits a high desalination capacity of 16.4 mg g-1 at an operation voltage of 1.2 V in 500 mg L-1 NaCl solution. Additionally, the hybrid CDI exhibits a good cycling stability with 18.3% decay in the desalination capacity after 20 electrosorption-desorption cycles. Thus, the Cu/Cu2O/C composite is expected to be a promising cathode material for hybrid CDI.

MgB2 Superconducting Joint Architecture with the Functionality to Screen External Magnetic Fields for MRI Magnet Applications.

A superconducting joint architecture to join unreacted carbon-doped multifilament magnesium diboride (MgB2) wires with the functionality to screen external magnetic fields for magnetic resonance imaging (MRI) magnet applications is proposed. The intrinsic diamagnetic property of a superconducting MgB2 bulk was exploited to produce a magnetic field screening effect around the current transfer path within the joint. Unprecedentedly, the joint fabricated using this novel architecture was able to screen magnetic fields up to 1.5 T at 20 K and up to 2 T at 15 K and thereby almost nullified the effect of the applied magnetic field by maintaining a constant critical current (Ic). The joint showed an Ic of 30.8 A in 1.5 T at 20 K and an ultralow resistance of about 3.32 × 10-14 Ω at 20 K in a self-field. The magnetic field screening effect shown by the MgB2 joint is expected to be extremely valuable for MRI magnet applications, where the Ic of the joints is lower than the Ic of the connected MgB2 wires in a given magnetic field and temperature.

Efficient lithium-ion storage using a heterostructured porous carbon framework and its in situ transmission electron microscopy study.

A heterostructured porous carbon framework (PCF) composed of reduced graphene oxide (rGO) nanosheets and metal organic framework (MOF)-derived microporous carbon is prepared to investigate its potential use in a lithium-ion battery. As an anode material, the PCF exhibits efficient lithium-ion storage performance with a high reversible specific capacity (771 mA h g-1 at 50 mA g-1), an excellent rate capability (448 mA h g-1 at 1000 mA g-1), and a long lifespan (75% retention after 400 cycles). The in situ transmission electron microscopy (TEM) study demonstrates that its unique three-dimensional (3D) heterostructure can largely tolerate the volume expansion. We envisage that this work may offer a deeper understanding of the importance of tailored design of anode materials for future lithium-ion batteries.

Recent Advances and Perspectives of Battery-Type Anode Materials for Potassium Ion Storage.

Potassium ion energy storage devices are competitive candidates for grid-scale energy storage applications owing to the abundancy and cost-effectiveness of potassium (K) resources, the low standard redox potential of K/K+, and the high ionic conductivity in K-salt-containing electrolytes. However, the sluggish reaction dynamics and poor structural instability of battery-type anodes caused by the insertion/extraction of large K+ ions inhibit the full potential of K ion energy storage systems. Extensive efforts have been devoted to the exploration of promising anode materials. This Review begins with a brief introduction of the operation principles and performance indicators of typical K ion energy storage systems and significant advances in different types of battery-type anode materials, including intercalation-, mixed surface-capacitive-/intercalation-, conversion-, alloy-, mixed conversion-/alloy-, and organic-type materials. Subsequently, host-guest relationships are discussed in correlation with the electrochemical properties, underlying mechanisms, and critical issues faced by each type of anode material concerning their implementation in K ion energy storage systems. Several promising optimization strategies to improve the K+ storage performance are highlighted. Finally, perspectives on future trends are provided, which are aimed at accelerating the development of K ion energy storage systems.

Effect of Heat Treatments under High Isostatic Pressure on the Transport Critical Current Density at 4.2 K and 20 K in Doped and Undoped MgB2 Wires.

Annealing undoped MgB2 wires under high isostatic pressure (HIP) increases transport critical current density (Jtc) by 10% at 4.2 K in range magnetic fields from 4 T to 12 T and significantly increases Jtc by 25% in range magnetic fields from 2 T to 4 T and does not increase Jtc above 4 T at 20 K. Further research shows that a large amount of 10% SiC admixture and thermal treatment under a high isostatic pressure of 1 GPa significantly increases the Jtc by 40% at 4.2 K in magnetic fields above 6 T and reduces Jtc by one order at 20 K in MgB2 wires. Additionally, our research showed that heat treatment under high isostatic pressure is more evident in wires with smaller diameters, as it greatly increases the density of MgB2 material and the number of connections between grains compared to MgB2 wires with larger diameters, but only during the Mg solid-state reaction. In addition, our study indicates that smaller wire diameters and high isostatic pressure do not lead to a higher density of MgB2 material and more connections between grains during the liquid-state Mg reaction.

Extracellular Vesicle Nanoarchitectonics for Novel Drug Delivery Applications.

Extracellular vesicles (EVs) can transfer intercellular messages in various (patho)physiological processes and transport biomolecules to recipient cells. EVs possess the capacity to evade the immune system and remain stable over long periods, identifying them as natural carriers for drugs and biologics. However, the challenges associated with EVs isolation, heterogeneity, coexistence with homologous biomolecules, and lack of site-specific delivery, have impeded their potential. In recent years, the amalgamation of EVs with rationally engineered nanostructures has been proposed for achieving effective drug loading and site-specific delivery. With the advancement of nanotechnology and nanoarchitectonics, different nanostructures with tunable size, shapes, and surface properties can be integrated with EVs for drug loading, target binding, efficient delivery, and therapeutics. Such integration may enable improved cellular targeting and the protection of encapsulated drugs for enhanced and specific delivery to target cells. This review summarizes the recent development of nanostructure amalgamated EVs for drug delivery, therapeutics, and real-time monitoring of disease progression. With a specific focus on the exosomal cargo, diverse drug delivery system, and biomimetic nanostructures based on EVs for selective drug delivery, this review also chronicles the needs and challenges of EV-based biomimetic nanostructures and provides a future outlook on the strategies posed.

ZIF-8 derived hollow carbon to trap polysulfides for high performance lithium-sulfur batteries.

Lithium-sulfur batteries (LSBs) have a high theoretical energy density and are low cost. However, the undesirable shuttle effect with the solid discharge product, Li2S, greatly impedes their market penetration. Conductive carbon materials with functional elements are beneficial in controlling the shuttle effect and can reactivate the Li2S, leading to improved long term cycling performance of LSBs. Herein, we report zinc (Zn) and nitrogen (N) co-doped ZIF-8 derived hollow carbon (ZHC) as a promising separator coating for LSBs to control the shuttle effect. The hollow area in the ZHC is identified to be around 250 nm with a carbonized outer surface thickness of approximately 50 nm. The presence of Zn and N in the nanohollow carbon structure helps to mitigate polysulfide (PS) diffusion in LSBs. Furthermore, the hollow interior of the carbon acts as a PS pocket to physically capture the PS and in addition Zn and N chemically attract the PS through polar-polar and metal sulfide interactions. The ZHC with its unique architecture and functional groups shows a promising performance with an initial specific capacity (S.cap) of 842 mA h g-1 at 4.80 mg cm-2 and cycling stability until 400 cycles, which is considerably higher in comparison with the cycling performance of parent ZIF-8.

Superconducting Joining Concept for Internal Magnesium Diffusion-Processed Magnesium Diboride Wires.

A superconducting joint of unreacted monofilament internal magnesium diffusion-processed magnesium diboride (MgB2) wires was fabricated by exploiting the phenomenon of magnesium diffusion into the boron layer inside the superconducting joint. Unprecedentedly, the joint was able to carry an almost identical transport current compared to the bare wire in a 2-7 T magnetic field at 20 K. The joint also exhibited very low joint resistance of 2.01 × 10-13 Ω in self-field at 20 K. Among commercially available superconductors, this work is the first to successfully realize a superconducting joint that is capable of transferring current from one conductor to another without any notable degradation under strong magnetic fields. This work demonstrates great potential to apply MgB2 in a range of practical applications, where superconducting joints are essential.

Nanoporous carbon nitride with a high content of inbuilt N site for the CO2 capture.

We report the nanoconfinement-mediated graphitic nanoporous carbon nitride (gNPCN) adsorbents with a high content of inbuilt basic nitrogen (N) (48%) by X-ray photoelectron spectroscopy (XPS) for efficient CO2 adsorption. The gNPCNs (gNPCN-150 and gNPCN-130) are synthesized using the mesoporous SBA-15 silica template and a single carbon-nitrogen (C-N) precursor (guanidine hydrochloride). The various adsorbents were utilized for investigating the influence of pore size (PS), surface area (SA), and type of adsorbent for CO2 adsorption performance. The capacity for CO2 capturing of gNPCN-150 reached 23.1 mmol/g at 0 °C under 30 bar pressure. This CO2 capturing capacity value was higher than the capacity gNPCN-130, SBA15, activated carbon (AC), and multiwalled carbon nanotube (MWCN) under identical conditions. The gNPCN materials exhibited superior CO2 adsorption ability that is ascribed to the presence of the highly organized mesoporosity, inbuilt high content of basic N site for adsorbing more CO2 through acid-base interaction, and tunable surface-structural properties. Moreover, the synthesis strategy is remarkably flexible in selecting C-N sources. This study features graphitic high-ordered nanoporous CN materials as a resourceful platform towards the efficient CO2 capture.

Fabrication of highly and poorly oxidized silver oxide/silver/tin(IV) oxide nanocomposites and their comparative anti-pathogenic properties towards hazardous food pathogens.

Herein, we report the fabrication of highly oxidized silver oxide/silver/tin(IV) oxide (HOSBTO or Ag3+-enriched AgO/Ag/SnO2) nanocomposite under a robust oxidative environment created with the use of concentrated nitric acid. Tin(IV) hydroxide nanofluid is added to the reaction mixture as a stabilizer for the Ag3+-enriched silver oxide in the nanocomposite. The formation of Ag nanoparticles in this nanocomposite originates from the decomposition of silver oxides during calcination at 600 °C. For comparison, poorly oxidized silver oxide/silver/tin(IV) oxide (POSBTO with formula AgO/Ag/SnO2) nanocomposite has also been prepared by following the same synthetic procedures, except for the use of concentrated nitric acid. Finally, we studied in detail the anti-pathogenic capabilities of both nanocomposites against four hazardous pathogens, including pathogenic fish bacterium (Stenotrophomonas maltophilia stain EP10), oomycete (Phytophthora cactorum strain P-25), and two different strains of pathogenic strawberry fungus, BRSP08 and BRSP09 (Collectotrichum siamense). The bioassays reveal that the as-prepared HOSBTO and POSBTO nanocomposites exhibit significant inhibitory activities against the tested pathogenic bacterium, oomycete, and fungus in a dose-dependent manner. However, the degree of dose-dependent effectiveness of the two nanocomposites against each pathogen largely varies.

In-situ incorporation of highly dispersed silver nanoparticles in nanoporous carbon nitride for the enhancement of antibacterial activities.

Graphitic carbon nitride with suitably incorporated functionality has attracted much interest in the areas of environmental treatments, clean energy, sensing, and photocatalyst. However, the role of graphitic nanoporous carbon nitride (NCN) matrix from single carbon-nitrogen (C-N) source, aminoguanidine HCl as a precursor and close intimate contact between silver nanoparticles (Ag NPs) dispersed in NCN and bacteria has rarely been demonstrated. Herein, we demonstrate a nanostructure of Ag NPs-incorporated NCN sample (NCN@Ag) as an antibacterial agent against both wild type and the multidrug-resistant Escherichia coli (E. coli) pathogens. In-situ ultrasonication method was used to ensure the homogeneous mixing of the Ag NPs and a single C-N precursor at the molecular level so that pore size (PS) (9.17 nm) of SBA15 silica could be impregnated with ultrasonicated Ag NPs and a single C-N precursor. The porous structure, compositions, and structural information of the final nanocomposites were confirmed by using various analytical techniques such as XRD, TEM, BET surface area (SA) measurements, XPS, and UV. Then, the antibacterial activities of the NCN and NCN@Ag against both wild type and the multidrug-resistant Escherichia coli (E. coli) pathogens were also carried out and results from the in-vitro studies have shown the excellent bactericidal effect of the highly dispersed Ag NPs containing NCN@Ag sample against both E. coli strains. Results have confirmed that the antibacterial activity of the NCN@Ag sample is found to be higher than pure NCN, indicating that in-situ incorporated Ag NPs in NCN matrix have played significant role for enhancing antibacterial activities. Surprisingly, in the presence of NCN@Ag, the reduction in minimum inhibitory concentration (MIC) was higher (64-fold reduction) compared to its susceptible wild type (32-fold reduction) E. coli. These results indicate the potential application of NCN@Ag for inactivating infectious bacterial pathogens implicated in multidrug resistance.

Nanostructured mesoporous gold biosensor for microRNA detection at attomolar level.

Advances in nanoarchitectonics enable a wide variety of nanostructured electrodes with tunable shapes and surface for constructing sensitive biosensors. Herein we demonstrate the fabrication of a mesoporous gold (Au) biosensor for the specific and sensitive detection of miRNA in a relatively simple and portable manner. The electrocatalytic activity of the mesoporous Au electrode (MPGE) towards the redox reaction of Fe(CN)6]3-/4- expansively examined. Leveraging the electrocatalytic activity and signal enhancement capacity of the MPGE, an ultrasensitive and specific electrochemical sensor was developed for the detection of microRNA (miRNA). The target miRNA from spiked samples is selectively isolated and purified using magnetic bead-capture probe followed by the direct adsorption on the MPGE through direct affinity interaction between miRNA and mesoporous Au surface. The MPGE-bound miRNA is then quantified by differential pulse voltammetry (DPV) using [Fe(CN)6]4-/3- redox system (Faradaic current decrease with reference to the bare MPGE). This method evades the cumbersome PCR (polymerase chain reaction) and enzymatic amplification steps. This is a single-step assay building which can detect a wide dynamic linear range (100 aM to 1 nM) of miRNA with an ultra-low limit detection of 100 aM and present high translational potentiality for the development of high-performance detection tools for clinics.