[Photoreactivation of Escherichia coli and Enterococcus faecalis in the secondary effluent disinfected by UV-TiO2].

Effects of photoreactivating light intensity (0-41 microW x cm(-2)) on photoreactivation of Escherichia coli (E. coli) and Enterococcus faecalis (E. faecalis) in the secondary effluent after UV and UV-TiO2 disinfection were investigated. The results indicated that the disinfection efficiency of UV-TiO2 was much higher than that of UV disinfection. The photoreactivation rate of E. coli was much higher in UV disinfection than that in UV-TiO2 disinfection. Under high light intensity in UV-TiO2 disinfection, high resurrection rate can be induced. However, a higher resurrection rate can be introduced even under low light intensity in the UV disinfection. Meanwhile, UV-TiO2 disinfection had a strong inhibition effect on E. faecalis photoreactivation, when the light intensity was lower than 21 microW x cm(-2), three was no resurrection occurred on E. faecalis after 72 h resurrection irradiation, only under a strong photoreactivating light intensity, the resurrection rate of E. faecalis was observed.

Star-shaped D-A small molecules based on diketopyrrolopyrrole and triphenylamine for efficient solution-processed organic solar cells.

Three star-shaped D-A small molecules, (P-DPP)(3)TPA, (4-FP-DPP)(3)TPA, and (4-BuP-DPP)(3)TPA were designed and synthesized with triphenylamine (TPA) as the core, diketopyrrolopyrrole (DPP) as the arm, and unsubstituted or substituted benzene rings (phenyl, P; 4-fluoro-phenyl, 4-FP; 4-n-butyl-phenyl, 4-BuP) as the end-group. All the three small molecules show relatively narrow optical band gaps (1.68-1.72 eV) and low-lying highest occupied molecular orbital (HOMO) energy levels (-5.09∼-5.13 eV), implying that they are potentially good electron donors for organic solar cells (OSCs). Then, photovoltaic properties of the small molecules blended with [6,6]-phenyl-C(61)-butyric acid methyl ester (PC(61)BM) as electron acceptor were investigated. Among three small molecules, the OSC based on (P-DPP)(3)TPA:PCBM blend exhibits a best power conversion efficiency (PCE) of 2.98% with an open-circuit voltage (V(oc)) of 0.72 V, a short-circuit current density (J(sc)) of 7.94 mA/cm(2), and a fill factor (FF) of 52.2%, which may be ascribed to the highest hole mobility of (P-DPP)(3)TPA.

Generation of native polythiophene/PCBM composite nanoparticles via the combination of ultrasonic micronization of droplets and thermocleaving from aqueous dispersion.

We report the preparation of native polythiophene (n-PT)/[6, 6]-phenyl-C61-butyric acid methyl ester (PCBM) composite nanoparticles from a poly[3-(2-methylhex-2-yl)oxy-carbonyldithiophene] (P3MHOCT)/PCBM aqueous dispersion prepared from an ultrasonically generated emulsion. The subsequent steps involve both ultrasonic generation of microdroplets in argon as a carrier gas and drying followed by thermocleaving of the P3MHOCT component in the gas phase. The chemical transition from P3MHOCT to n-PT was confirmed by Fourier transform infrared (FTIR) spectroscopy. The morphology and size of n-PT/PCBM nanoparticles were determined by atomic force microscopy (AFM), small-angle x-ray scattering (SAXS) and grazing incidence SAXS (GISAXS), giving an average size of ∼ 140 nm. The GISAXS results reveal that n-PT/PCBM nanoparticles pack in an ordered structure as opposed to the P3MHOCT/PCBM nanoparticles. The successful vapour-phase preparation of phase-separated n-PT/PCBM nanoparticles provides a new route to all-aqueous processing of conjugated materials relevant to efficient polymer solar cells with long operational stability. The use of ultrasound was involved in both liquid and gas phases demonstrating it as a low-cost processing method.