TiO2-embedded mesoporous silica with lower porosity is beneficial to adsorb the pollutants and retard UV filter absorption: A possible application for outdoor skin protection.

The purpose of the current investigation was to develop multifunctional TiO2-embedded mesoporous silica incorporating avobenzone to protect against environmental stress through pollutant adsorption and UVA protection. We sought to explore the effect of the mesoporous porosity on the capability of contaminant capture and the suppression of avobenzone skin penetration. The porosity of the mesoporous silica was tuned by adjusting the ratio of template triblock copolymers (Pluronic P123 and F68). The Pluronic P123:F68 ratios of 3:1, 2:2, and 1:3 produced mesoporous silica with pore volumes of 0.66 (TiO2/SBA-L), 0.47 (TiO2/SBA-M), and 0.25 (TiO2/SBA-S) cm3/g, respectively. X-ray scattering and electron microscopy confirmed the SBA-15 structure of the as-prepared material had a size of 3-5 µm. The maximum adsorbability of fluoranthene and methylene blue was found to be 43% and 53% for the TiO2/SBA-S under UVA light, respectively. The avobenzone loaded into the mesoporous silica demonstrated the synergistic effect of in vitro UVA protection, reaching an UVA/UVB absorbance ratio of near 1.5 (Boots star rating = 5). The encapsulation of avobenzone into the TiO2/SBA-S lessened cutaneous avobenzone absorption from 0.76 to 0.50 nmol/mg, whereas no reduction was detected for the TiO2/SBA-L. The avobenzone-loaded TiO2/SBA-S hydrogel exhibited a greater improvement in skin barrier recovery and proinflammatory mediator mitigation compared to the SBA-S hydrogel (without TiO2). The cytokines/chemokines in the photoaged skin were reduced by two- to three-fold after TiO2/SBA-S treatment compared to the non-treatment control. Our data suggested that the mesoporous formulation with low porosity and a specific surface area showed effective adsorbability and UVA protection, with reduced UVA filter absorption. The versatility of the developed mesoporous system indicated a promising potential for outdoor skin protection.

Body Weight Gain Status during the Incubator Weaning Process in Very Low Birth Weight Premature Infants.

Incubator care is essential for premature infants during early hospitalization. As the infants' conditions improve, incubator weaning becomes necessary. This retrospective study aimed to evaluate the effect of body weight gain and status of intake-calorie gain on the incubator weaning process for very low birth weight (VLBW) premature infants. The study included 127 VLBW premature neonates. We analyzed data on clinical characteristics potentially associated with the weaning period and the end-weaning body weight (EWBW), including body weight gain status, intake-calorie gain status, and disease conditions. The neonates were weaned from the incubators at a mean postmenstrual age (PMA) of 35.1 ± 1.3 weeks; postnatal days, 37.7 ± 18.2 days; and body weight, 1882.8 ± 157.1 g. The total weaning period was 3.5 ± 3.1 days. Regarding the weaning period, there was a strong positive relationship only in the end-weaning PMA and the daily body weight within 3 days before incubator weaning. Further, regarding the factors associated with EWBW, only the end-weaning PMA and necrotizing enterocolitis had a significant positive impact. Body weight gain and the status of intake-calorie gain showed no association with either the weaning period or the EWBW and, thus, were not related to the incubator weaning process.

Incidence of plastic ingestion by the shortfin mako, Isurus oxyrinchus, off the northeast coast of Taiwan.

This present study documents the incidence of plastic digestion by shortfin mako shark (Isurus oxyrinchus), caught by the Taiwanese small-scale tuna longline fishery in the Northwest Pacific Ocean (between the northeast coast of Taiwan and Japan). In 20 stomachs of shortfin mako, nearly 10% of samples contained at least one piece of plastic debris. The ingested plastic debris was found in the forms of films (5.0 cm) and fragments (3.0 mm) and was identified as polypropylene (PP) based on its polymer characteristics. The results from the analysis provide evidence for the anthropogenic origin and potential intake pathway of direct engulfment of ingested plastics. Our results also confirmed the low incidence of plastic ingestion in shortfin mako, suggesting that pelagic marine species may be relatively less affected by plastic pollution. Future research efforts are thus needed to assess the long-term impact of plastic pollution on marine species.

Ultrafast Graphene Growth on Insulators via Metal-Catalyzed Crystallization by a Laser Irradiation Process: From Laser Selection, Thickness Control to Direct Patterned Graphene Utilizing Controlled Layer Segregation Process.

Despite the vast progress in chemical vapor deposition (CVD) graphene grown on metals, the transfer process is still a major bottleneck, being not devoid of wrinkles and polymer residues. In this paper, a structure is introduced to directly synthesize few layer graphene on insulating substrates by a laser irradiation heating process. The segregation of graphene layers can be manipulated by tuning the metal layer thickness and laser power at different scanning rates. Graphene deposition and submicrometer patterning resolution can be achieved by patterning the intermediate metal layer using standard lithography methods in order to overcome the scalability issue regardless the resolution of the laser beam. The systematic analysis of the process based on the formation of carbon microchannels by the laser irradiation process can be extended to several materials, thicknesses, and methods. Furthermore, hole and electron mobilities of 500 and 950 cm(2) V(-1) s(-1) are measured. The laser-synthesized graphene is a step forward along the direct synthesis route for graphene on insulators that meets the criteria for photonics and electronics.