Investigation of the Influence of Infrared Illumination on the Pulse Shapes of Output Signals of CdZnTe Detectors.

The spectrometric characteristics of CdZnTe detectors are largely determined by the nonuniformity of the material and the influence of the negative polarization effects associated with the formation of space charges in the sensitive volume of the detector. They change the electric field distribution in the detector and affect the efficiency of the charge carrier collection. An analysis of the waveforms of the output pulses was used to investigate the uniformity of the charge collection and electric field distribution in the detectors when irradiated by the alpha particles. The influence of infrared (IR) illumination on these parameters was evaluated. IR illumination had no positive effect on the planar detector but greatly improved the charge collection in quasi-hemispherical detectors in the peripheral (corner) regions. The output pulse amplitude increased, and the rise time notably decreased. Polarization that occurred predominantly in the corner regions at low temperatures (from -30 °C to -20 °C) was eliminated using IR illumination.

Use of CdZnTe Quasi-Hemispherical Detectors under the Impact of Low Temperatures and High-Gamma Radiation Fluxes.

This article discusses the possibilities and limitations of CdZnTe (CZT) quasi-hemispherical detectors operating over a wide temperature range and at high-gamma radiation fluxes. The results of the negative influence of low- and high-operating temperatures, as well as high-radiation fluxes on spectrometric characteristics of CZT detectors and possible ways to eliminate performance deterioration, are presented. The impact of infrared (IR) illumination parameters, such as wavelength and irradiation intensity on the spectroscopy performance of detectors, was investigated. A correctly chosen IR illumination wavelength and intensity were shown to significantly improve the energy resolution of CZT quasi-hemispherical detectors, allowing their stable operation in high-gamma radiation fluxes and extend the operating temperature range toward low temperatures. The influences of bias voltage values and temperatures on the quasi-hemispherical CZT detectors' operating ability at high-gamma radiation fluxes were studied.

Electrical Resistivity of 3D-Printed Polymer Elements.

During this study, the resistivity of electrically conductive structures 3D-printed via fused filament fabrication (FFF) was investigated. Electrical resistivity characterisation was performed on various structural levels of the whole 3D-printed body, starting from the single traxel (3D-printed single track element), continuing with monolayer and multilayer formation, finalising with hybrid structures of a basic nonconductive polymer and an electrically conductive one. Two commercial conductive materials were studied: Proto-Pasta and Koltron G1. It was determined that the geometry and resistivity of a single traxel influenced the resistivity of all subsequent structural elements of the printed body and affected its electrical anisotropy. In addition, the results showed that thermal postprocessing (annealing) affected the resistivity of a standalone extruded fibre (extruded filament through a printer nozzle in freefall) and traxel. The effect of Joule heating and piezoresistive properties of hybrid structures with imprinted conductive elements made from Koltron G1 were investigated. Results revealed good thermal stability within 70 °C and considerable piezoresistive response with a gauge factor of 15-25 at both low 0.1% and medium 1.5% elongations, indicating the potential of such structures for use as a heat element and strain gauge sensor in applications involving stiff materials and low elongations.

Spark Discharge Synthesis and Characterization of Ge/Sn Janus Nanoparticles.

Germanium-tin nanoparticles are promising materials for near- and mid-infrared photonics thanks to their tunable optical properties and compatibility with silicon technology. This work proposes modifying the spark discharge method to produce Ge/Sn aerosol nanoparticles during the simultaneous erosion of germanium and tin electrodes. Since tin and germanium have a significant difference in the potential for electrical erosion, an electrical circuit damped for one period was developed to ensure the synthesis of Ge/Sn nanoparticles consisting of independent germanium and tin crystals of different sizes, with the ratio of the atomic fraction of tin to germanium varying from 0.08 ± 0.03 to 0.24 ± 0.07. We investigated the elemental and phase composition, size, morphology, and Raman and absorbance spectra of the nanoparticles synthesized under different inter-electrode gap voltages and the presence of additional thermal treatment directly in a gas flow at 750 °C. The research shows that the in-flow thermal treatment of aerosol-agglomerated nanoparticles produced special individual bicrystalline Janus Ge/Sn nanoparticles with an average size of 27 nm and a decreasing absorption function with a changing slope at 700 nm.

Effect of Au Nanoparticle Agglomeration on SERS Signal Amplification.

An analyzed substance's signal intensity and detection sensitivity in surface-enhanced Raman spectroscopy (SERS) significantly depend on the size and agglomeration degree of nanoparticles (NPs) forming the enhancing structure. Structures were manufactured by aerosol dry printing (ADP), where NPs' agglomeration depends on printing conditions and additional particle modification techniques. The influence of agglomeration degree on SERS signal enhancement was studied in three types of printed structures using the methylene blue model molecule as an analyte. We demonstrated that the ratio between individual NPs and agglomerates in a studied structure strongly affects SERS signal amplification, and structures formed mainly from non-agglomerated NPs enhance the signal better. In this sense, aerosol NPs modified by pulsed laser radiation provide better results than thermally modified NPs, since in laser modification a larger number of individual NPs is observed due to the absence of secondary agglomeration effects in the gas stream. However, increasing gas flow may minimize the secondary agglomeration, since the time allotted for the agglomeration processes is reduced. In this paper, we show how different NPs' agglomeration tendencies influence SERS enhancement to demonstrate the process of using ADP to form inexpensive and highly efficient SERS substrates with huge application potential.

Ionising radiation and cardiovascular disease: systematic review and meta-analysis.

OBJECTIVE: To systematically review and perform a meta-analysis of radiation associated risks of cardiovascular disease in all groups exposed to radiation with individual radiation dose estimates. DESIGN: Systematic review and meta-analysis. MAIN OUTCOME MEASURES: Excess relative risk per unit dose (Gy), estimated by restricted maximum likelihood methods. DATA SOURCES: PubMed and Medline, Embase, Scopus, Web of Science Core collection databases. ELIGIBILITY CRITERIA FOR SELECTING STUDIES: Databases were searched on 6 October 2022, with no limits on date of publication or language. Animal studies and studies without an abstract were excluded. RESULTS: The meta-analysis yielded 93 relevant studies. Relative risk per Gy increased for all cardiovascular disease (excess relative risk per Gy of 0.11 (95% confidence interval 0.08 to 0.14)) and for the four major subtypes of cardiovascular disease (ischaemic heart disease, other heart disease, cerebrovascular disease, all other cardiovascular disease). However, interstudy heterogeneity was noted (P<0.05 for all endpoints except for other heart disease), possibly resulting from interstudy variation in unmeasured confounders or effect modifiers, which is markedly reduced if attention is restricted to higher quality studies or those at moderate doses (<0.5 Gy) or low dose rates (<5 mGy/h). For ischaemic heart disease and all cardiovascular disease, risks were larger per unit dose for lower dose (inverse dose effect) and for fractionated exposures (inverse dose fractionation effect). Population based excess absolute risks are estimated for a number of national populations (Canada, England and Wales, France, Germany, Japan, USA) and range from 2.33% per Gy (95% confidence interval 1.69% to 2.98%) for England and Wales to 3.66% per Gy (2.65% to 4.68%) for Germany, largely reflecting the underlying rates of cardiovascular disease mortality in these populations. Estimated risk of mortality from cardiovascular disease are generally dominated by cerebrovascular disease (around 0.94-1.26% per Gy), with the next largest contribution from ischaemic heart disease (around 0.30-1.20% per Gy). CONCLUSIONS: Results provide evidence supporting a causal association between radiation exposure and cardiovascular disease at high dose, and to a lesser extent at low dose, with some indications of differences in risk between acute and chronic exposures, which require further investigation. The observed heterogeneity complicates a causal interpretation of these findings, although this heterogeneity is much reduced if only higher quality studies or those at moderate doses or low dose rates are considered. Studies are needed to assess in more detail modifications of radiation effect by lifestyle and medical risk factors. SYSTEMATIC REVIEW REGISTRATION: PROSPERO CRD42020202036.

Plasmon-Enhanced Ultraviolet Luminescence in Colloid Solutions and Nanostructures Based on Aluminum and ZnO Nanoparticles.

Aluminum nanoparticles attract scientific interest as a promising low-cost material with strong plasmon resonance in the ultraviolet region, which can be used in various fields of photonics. In this paper, for the first time, ultraviolet luminescence of zinc oxide nanoparticles in colloid solutions and nanostructure films in the presence of plasmonic aluminum nanoparticles 60 nm in size with a metal core and an aluminum oxide shell were studied. Mixture colloids of ZnO and Al nanoparticles in isopropyl alcohol solution with concentrations from 0.022 to 0.44 g/L and 0.057 to 0.00285 g/L, correspondingly, were investigated. The enhancement of up to 300% of ZnO emission at 377 nm in colloids mixtures with metal nanoparticles due to formation of Al-ZnO complex agglomerates was achieved. Plasmon nanostructures with different configurations of layers, such as Al on the surface of ZnO, ZnO on Al, sandwich-like structure and samples prepared from a colloidal mixture of ZnO and Al nanoparticles, were fabricated by microplotter printing. We demonstrated that photoluminescence can be boosted 2.4-fold in nanostructures prepared from a colloidal mixture of ZnO and Al nanoparticles, whereas the sandwich-like structure gave only 1.1 times the amplification of luminescence. Calculated theoretical models of photoluminescence enhancement of ideal and weak emitters near aluminum nanoparticles of different sizes showed comparable results with the obtained experimental data.

Neutrophil Activation by Mineral Microparticles Coated with Methylglyoxal-Glycated Albumin.

Hyperglycemia-induced protein glycation and formation of advanced glycation end-products (AGEs) plays an important role in the pathogenesis of diabetic complications and pathological biomineralization. Receptors for AGEs (RAGEs) mediate the generation of reactive oxygen species (ROS) via activation of NADPH-oxidase. It is conceivable that binding of glycated proteins with biomineral particles composed mainly of calcium carbonate and/or phosphate enhances their neutrophil-activating capacity and hence their proinflammatory properties. Our research managed to confirm this hypothesis. Human serum albumin (HSA) was glycated with methylglyoxal (MG), and HSA-MG was adsorbed onto mineral microparticles composed of calcium carbonate nanocrystals (vaterite polymorph, CC) or hydroxyapatite nanowires (CP). As scopoletin fluorescence has shown, H2O2 generation by neutrophils stimulated with HSA-MG was inhibited with diphenyleneiodonium chloride, wortmannin, genistein and EDTA, indicating a key role for NADPH-oxidase, protein tyrosine kinase, phosphatidylinositol 3-kinase and divalent ions (presumably Ca2+) in HSA-MG-induced neutrophil respiratory burst. Superoxide anion generation assessed by lucigenin-enhanced chemiluminescence (Luc-CL) was significantly enhanced by free HSA-MG and by both CC-HSA-MG and CP-HSA-MG microparticles. Comparing the concentrations of CC-bound and free HSA-MG, one could see that adsorption enhanced the neutrophil-activating capacity of HSA-MG.

Aerosol Dry Printing for SERS and Photoluminescence-Active Gold Nanostructures Preparation for Detection of Traces in Dye Mixtures.

We proposed a novel method of nanostructure preparation for observation of surface-enhanced Raman spectroscopy (SERS) and metal-enhanced fluorescence (MEF) based on the deposition of gold nanoparticles (GNPs) above the thin dye film by dry aerosol printing. We detected various enhanced SERS and MEF signals of films of malachite green (MG) and rhodamine B (RhB) mixtures, depending on the surface packing density of Au NPs on the strip, and found the optimum one to achieve the 3.5 × 105 SERS enhancement. It was shown that statistical methods of chemometrics such as projection on latent structures provided the opportunity to distinguish SERS of MG from 100 ppm RhB in a mixture, whereas separation of MEF signals are feasible even for a mixture of MG and 1 ppm RhB due to two-photon excitation.

Silver Flowerlike Structures for Surface-Enhanced Raman Spectroscopy.

Micro- and nanoflowers are a class of materials composed of particles with high surface-to-volume ratio. They have been extensively studied in the last decade due to simple preparation protocols and promising applications in biosensing, as drug delivery agents, for water purification, and so on. Flowerlike objects, due to their highly irregular surface, may act also as plasmonic materials, providing resonant coupling between optical waves and surface plasmon excitations. This fact allows us to infer the possibility to use micro- and nanoflowers as effective surface-enhanced Raman scattering (SERS) substrate materials. Here, we report on the design and Raman enhancement properties of silver flowerlike structures, deposited on aluminum surface. A simple and cost-effective fabrication method is described, which leads to SERS substrates of high developed surface area. The morphology of the silver flowers on a nanoscale is characterized by self-organized quasiperiodic stacks of nanosheets, which act as plasmonic cavity resonators. The substrates were tested against rhodamine-6G (R6G) water solutions of concentration varying between 10-3 M and 10-7 M. Optimal SERS enhancement factors of up to 105 were established at R6G concentrations in the 10-6-10-7 M range.

Modification of Aerosol Gold Nanoparticles by Nanosecond Pulsed-Periodic Laser Radiation.

This study investigates the processes of interaction of nanosecond pulsed-periodic laser radiation with the flow of aerosol agglomerates of gold nanoparticles synthesized in a spark discharge. Nanoparticles in a gas flow are spatially separated nano-objects whose interaction with each other and with the walls of an experimental cell was insignificant. Therefore, the energy absorbed by nanoparticles was used only for their own heating with further shape and size modification and on heat transfer to the surrounding gas. In the research, we used laser radiation with wavelengths of 527 and 1053 nm at pulse energies up to 900 µJ and pulse repetition rates up to 500 Hz. The dynamics of changes in the nanoparticles size during their sintering process depending on the laser pulses energy is characterized by an S-shaped shrinkage curve. Complete sintering of the initial agglomerates with their transformation into spherical nanoparticles is achieved by a series of impacting laser pulses. The result of nanoparticles' laser modification is largely determined by the pulse energy and the efficiency of the nanoparticles' radiation absorption.

The quiescent centre of the root apical meristem: conceptual developments from Clowes to modern times.

In this review we discuss the concepts of the quiescent centre (QC) of the root apical meristem (RAM) and their change over time, from their formulation by F.A.L. Clowes to the present. This review is dedicated to the 100th anniversary of the birth of Clowes, and we present his short biography and a full bibliography of Clowes' work. Over time, the concept of the QC proved to be useful for the understanding of RAM organization and behaviour. We focus specifically on conceptual developments, from the organization of the QC to understanding its functions in RAM maintenance and activity, ranging from a model species, Arabidopsis thaliana, to crops. Concepts of initial cells, stem cells, and heterogeneity of the QC cells in the context of functional and structural stem cells are considered. We review the role of the QC in the context of cell flux in the RAM and the nature of quiescence of the QC cells. We discuss the origin of the QC and fluctuation of its size in ontogenesis and why the QC cells are more resistant to stress. Contemporary concepts of the organizer and stem cell niche are also considered. We also propose how the stem cell niche in the RAM can be defined in roots of a non-model species.

Optimizing Aerosol Jet Printing Process of Platinum Ink for High-Resolution Conductive Microstructures on Ceramic and Polymer Substrates.

Printing nano-ink with platinum nanoparticles to generate conductive microstructures for electronics on different types of substrates has gained increasing interest in recent years. To solve the problem of the low conductivity of platinum (Pt) nano-ink, we synthesized chemically pure Pt nanoparticles with sizes of 18.2 ± 9.0 nm by spark discharge method. A low toxic solvent, ethylene glycol with water, was used to ensure the aggregation stability of Pt nanoparticles. Polyvinylpyrrolidone was used as an adhesive additive and binder in the nano-ink. Narrow and conductive Pt lines were generated by aerosol jet printing technology. The resistivity of the Pt lines sintered at 750 °C on alumina substrate was found to exceed the bulk Pt by about 13%. Moreover, the Pt film fabricated on polymer substrates has demonstrated excellent mechanical flexibility in terms of twisting tests.

Synthesis of Nanoparticles by Spark Discharge as a Facile and Versatile Technique of Preparing Highly Conductive Pt Nano-Ink for Printed Electronics.

A cost-effective, scalable and versatile method of preparing nano-ink without hazardous chemical precursors is a prerequisite for widespread adoption of printed electronics. Precursor-free synthesis by spark discharge is promising for this purpose. The synthesis of platinum nanoparticles (PtNPs) using a spark discharge under Ar, N2, and air has been investigated to prepare highly conductive nano-ink. The size, chemical composition, and mass production rate of PtNPs significantly depended on the carrier gas. Pure metallic PtNPs with sizes of 5.5 ± 1.8 and 7.1 ± 2.4 nm were formed under Ar and N2, respectively. PtNPs with sizes of 18.2 ± 9.0 nm produced using air consisted of amorphous oxide PtO and metallic Pt. The mass production rates of PtNPs were 53 ± 6, 366 ± 59, and 490 ± 36 mg/h using a spark discharge under Ar, N2, and air, respectively. It was found that the energy dissipated in the spark gap is not a significant parameter that determines the mass production rate. Stable Pt nano-ink (25 wt.%) was prepared only on the basis of PtNPs synthesized under air. Narrow (about 30 µm) and conductive Pt lines were formed by the aerosol jet printing with prepared nano-ink. The resistivity of the Pt lines sintered at 750 °C was (1.2 ± 0.1)·10-7 Ω·m, which is about 1.1 times higher than that of bulk Pt.

Comparison of Aerosol Pt, Au and Ag Nanoparticles Agglomerates Laser Sintering.

In this paper, we investigated the interaction of nanosecond pulsed-periodic infrared (IR) laser radiation at a 50 and 500 Hz repetition rate with aerosol platinum (Pt) and silver (Ag) nanoparticles agglomerates obtained in a spark discharge. Results showed the complete transformation of Pt dendrite-like agglomerates with sizes of 300 nm into individual spherical nanoparticles directly in a gas flow under 1053 nm laser pulses with energy density 3.5 mJ/cm2. Notably, the critical energy density required for this process depended on the size distribution and extinction of agglomerates nanoparticles. Based on the extinction cross-section spectra results, Ag nanoparticles exhibit a weaker extinction in the IR region in contrast to Pt, so they were not completely modified even under the pulses with energy density up to 12.7 mJ/cm2. The obtained results for Ag and Pt laser sintering were compared with corresponding modification of gold (Au) nanoparticles studied in our previous work. Here we considered the sintering mechanisms for Ag, Pt and Au nanoparticles agglomerates in the aerosol phase and proposed the model of their laser sintering based on one-stage for Pt agglomerates and two-stage shrinkage processes for Au and Ag agglomerates.

Study of Dispersions of Carbon Nanotubes Modified by the Method of Rapid Expansion of Supercritical Suspensions.

The effectiveness of carbon nanotubes (CNT) deagglomeration by rapid expansion of supercritical suspensions (RESS) in nitrogen and carbon dioxide fluids was studied in this work. Two different mechanisms of deagglomeration were proposed for these two fluids at various temperature and pressure conditions. Ultrasound attenuation spectroscopy was applied as an express method of determining median diameter and aspect ratio of CNTs. At least twofold reduction of the diameter was shown for CNT bundles processed by RESS technique. Aspect ratio of processed CNTs, calculated from acoustic attenuation spectra, increased to 340. These results were in a good agreement with atomic force microscopy data.

Detection of potential biodeterioration risks for tempera painting in 16th century exhibits from State Tretyakov Gallery.

In this study, we investigated biodeterioration of materials used in tempera painting by analyzing the structure of the microbiome in ancient tempera paintings exhibited in State Tretyakov Gallery, Moscow, Russia. Samples were obtained from 16th-century paintings, including a grand Russian Orthodox icon "The Church Militant" (all exhibits were without visible signs of biodeterioration), and from surrounding walls and ceilings (with vast zones of visible microbial growth). A number of microorganisms isolated from visible signs of environmental bio-damage were also detected in tempera paintings kept in temperature- and humidity-controlled conditions unfavorable for the growth of microflora. To determine the biodegrading potential of the microbiome for tempera paintings, we developed a set of mock layers from paintwork materials used in tempera painting of 16th century and their modern analogues and inoculated them with cultures containing filamentous fungi and bacteria. The susceptibility to microbial degradation of individual tempera painting materials was examined by micro-Fourier Transform Infrared (FTIR) spectroscopy, which enabled detection of even invisible signs of biodeterioration. The results indicate that the microorganisms isolated from paintings and surrounding areas in the museum are capable of causing significant damage of various tempera materials, among which varnishes were the most resistant; however, the addition of antiseptic (sodium pentachlorophenolate) can inhibit microbial growth on sturgeon glue.

Aerosol Jet Printing of Silver Lines with A High Aspect Ratio on A Heated Silicon Substrate.

In this work, we studied the formation of conductive silver lines with high aspect ratios (AR = thickness/width) > 0.1 using the modernized method of aerosol jet printing on a heated silicon substrate. The geometric (AR) and electrical (resistivity) parameters of the formed lines were investigated depending on the number of printing layers (1-10 layers) and the temperature of the substrate (25-300 °C). The AR of the lines increased as the number of printing layers and the temperature of the substrate increased. An increase in the AR of the lines with increasing substrate temperature was associated with a decrease in the ink spreading as a result of an increase in the rate of evaporation of nano-ink. Moreover, with an increase in the substrate temperature of more than 200 °C, a significant increase in the porosity of the formed lines was observed, and as a result, the electrical resistivity of the lines increased significantly. Taking into account the revealed regularities, it was demonstrated that the formation of silver lines with a high AR > 0.1 and a low electrical resistivity of 2-3 µΩ∙cm is advisable to be carried out at a substrate temperature of about 100 °C. The adhesion strength of silver films formed on a heated silicon substrate is 2.8 ± 0.9 N/mm2, which further confirms the suitability of the investigated method of aerosol jet printing for electronic applications.

Binding of Cys2His2 transcription factors with operator DNA: functional role of linkers between Zn-fingers.

Communicated by Ramaswamy H. Sarma.

Violence Exposure, Posttraumatic Stress, and Subjective Well-Being in a Sample of Russian Adults: A Facebook-Based Study.

Exposure to violence has been shown to negatively affect mental health and well-being. The goal of this Facebook-based study was to describe the rates of exposure to violence in a sample of Russian adults and to assess the impact of these experiences on subjective well-being and victimization-related psychological distress. Three types of victimization were assessed: physical assault by a stranger, physical assault by someone known to victim, and nonconsensual sexual experiences. The 5-item World Health Organization Well-Being Index (WHO-5) was used to assess subjective well-being, and Primary Care PTSD Screen (PC-PTSD) was employed as an indicator of victimization-related psychological distress. Data were obtained from 6,724 Russian-speaking Facebook users. Significant levels of lifetime victimization were reported by the study participants. Lifetime physical assault by a stranger, physical assault by someone known to victim, and sexual assault were reported by 56.9%, 64.2%, and 54.1% of respondents, respectively. Respondents exposed to violence were more likely to report posttraumatic stress symptoms and lower levels of subjective well-being. Participants who were exposed to at least one type of violence were more likely to experience symptoms of traumatic stress (U = 1,794,250.50, p < .001, d = 0.35). Exposure to multiple forms of violence was associated with more severe traumatic stress symptoms (rs = .257, p < .001). Well-being scores were significantly lower among participants exposed to violence (t = 8.37, p < .001, d = 0.31). The study demonstrated that violence exposure is associated with reduced well-being among Russian adults. Our findings highlight the negative impact of violence exposure on subjective well-being and underscore the necessity to develop programs addressing violence exposure in Russian populations.