Optimizing microwave-assisted production of waste-based activated carbons for the removal of antibiotics from water.

This work aimed at the microwave-assisted production of activated carbon (AC) from primary paper mill sludge (PS) for the adsorption of antibiotics from water. Production conditions, namely pyrolysis temperature, pyrolysis time and activating agent (KOH):PS ratio, were optimized as a function of product yield, specific surface area (SBET), total organic carbon (TOC) content and adsorptive removal percentage of two target antibiotics (amoxicillin (AMX) and sulfamethoxazole (SMX)). Under the optimized conditions (pyrolysis at 800 °C during 20 min and a KOH:PS ratio of 1:5), a microporous AC (MW800-20-1:5, with SBET = 1196 m2 g-1, TOC = 56.2% and removal of AMX and SMX = 85% and 72%, respectively) was produced and selected for further kinetic and equilibrium adsorption studies. The obtained results were properly described by the Elovich reaction-based kinetic model and the Langmuir equilibrium isotherm, with maximum adsorption capacities of 204 ± 5 mg g-1 and 217 ± 8 mg g-1 for AMX and SMX, respectively. Considering the satisfactory comparison of these results with the performance of commercial and alternative AC produced by conventional pyrolysis, this work demonstrated the feasibility of the microwave-assisted production of environmentally and energetically sustainable waste-based AC to be applied in the efficient removal of antibiotics from water.

Core-Shell Molecularly Imprinted Polymers on Magnetic Yeast for the Removal of Sulfamethoxazole from Water.

In this work, magnetic yeast (MY) was produced through an in situ one-step method. Then, MY was used as the core and the antibiotic sulfamethoxazole (SMX) as the template to produce highly selective magnetic yeast-molecularly imprinted polymers (MY@MIPs). The physicochemical properties of MY@MIPs were assessed by Fourier-transform infrared spectroscopy (FT-IR), a vibrating sample magnetometer (VSM), X-ray diffraction (XRD), thermogravimetric analysis (TGA), specific surface area (SBET) determination, and scanning electron microscopy (SEM). Batch adsorption experiments were carried out to compare MY@MIPs with MY and MY@NIPs (magnetic yeast-molecularly imprinted polymers without template), with MY@MIPs showing a better performance in the removal of SMX from water. Adsorption of SMX onto MY@MIPs was described by the pseudo-second-order kinetic model and the Langmuir isotherm, with maximum adsorption capacities of 77 and 24 mg g-1 from ultrapure and wastewater, respectively. Furthermore, MY@MIPs displayed a highly selective adsorption toward SMX in the presence of other pharmaceuticals, namely diclofenac (DCF) and carbamazepine (CBZ). Finally, regeneration experiments showed that SMX adsorption decreased 21 and 34% after the first and second regeneration cycles, respectively. This work demonstrates that MY@MIPs are promising sorbent materials for the selective removal of SMX from wastewater.

Monitoring pharmaceuticals in the aquatic environment using enzyme-linked immunosorbent assay (ELISA)-a practical overview.

The presence of pharmaceuticals, which are considered as contaminants of emerging concern, in natural waters is currently recognized as a widespread problem. Monitoring these contaminants in the environment has been an important field of research since their presence can affect the ecosystems even at very low levels. Several analytical techniques have been developed to detect and quantify trace concentrations of these contaminants in the aquatic environment, namely high-performance liquid chromatography, gas chromatography, and capillary electrophoresis, usually coupled to different types of detectors, which need to be complemented with time-consuming and costly sample cleaning and pre-concentration procedures. Generally, the enzyme-linked immunosorbent assay (ELISA), as other immunoassay methodologies, is mostly used in biological samples (most frequently urine and blood). However, during the last years, the number of studies referring the use of ELISA for the analysis of pharmaceuticals in complex environmental samples has been growing. Therefore, this work aims to present an overview of the application of ELISA for screening and quantification of pharmaceuticals in the aquatic environment, namely in water samples and biological tissues. The experimental procedures together with the main advantages and limitations of the assay are addressed, as well as new incomes related with the application of molecular imprinted polymers to mimic antibodies in similar, but alternative, approaches. Graphical Abstract.

Fixed-bed performance of a waste-derived granular activated carbon for the removal of micropollutants from municipal wastewater.

This work aimed to assess the fixed-bed adsorptive performance of a primary paper mill sludge-based granular activated carbon (PSA-PA) for the removal of pharmaceuticals, namely carbamazepine (CBZ), sulfamethoxazole (SMX) and paroxetine (PAR), from water. The breakthrough curves corresponding to the adsorption of CBZ at different flow rates and in two different matrices (distilled and municipal wastewater) were firstly determined, which allowed to select the most favorable flow rate for the subsequent experiments. The fixed-bed adsorption of CBZ, SMX and PAR from single and ternary solutions in wastewater showed that the performance of PSA-PA was different for each pharmaceutical. According to the obtained breakthrough curves, the poorest bed adsorption capacity, either from single or ternary solution, was observed for SMX, which may be related with electrostatic repulsion at the pH of the wastewater used (pH ~ 7.3-7.7). Also, the bed adsorption capacity of PSA-PA for SMX, in the ternary solution, was notoriously lower compared to the single solution, while it slightly decreased for CBZ and even increased for PAR. The regeneration studies showed that the CBZ adsorption capacity of the PSA-PA bed decreased about 38 and 71% after the first and the second thermal regeneration stages, respectively. This decline was comparatively larger than the corresponding reduction of the PSA-PA specific surface area (SBET), which decreased only 5 and 25% for the first and second regeneration stages, respectively, and pointed to the lack of viability of more than one regeneration stage.

Adsorption of pharmaceuticals from biologically treated municipal wastewater using paper mill sludge-based activated carbon.

A waste-based alternative activated carbon (AAC) was produced from paper mill sludge under optimized conditions. Aiming its application in tertiary wastewater treatment, AAC was used for the removal of carbamazepine, sulfamethoxazole, and paroxetine from biologically treated municipal wastewater. Kinetic and equilibrium adsorption experiments were run under batch operation conditions. For comparison purposes, they were also performed in ultrapure water and using a high-performance commercial AC (CAC). Adsorption kinetics was fast for the three pharmaceuticals and similar onto AAC and CAC in either wastewater or ultrapure water. However, matrix effects were observed in the equilibrium results, being more remarkable for AAC. These effects were evidenced by Langmuir maximum adsorption capacities (qm, mg g-1): for AAC, the lowest and highest qm were 194 ± 10 (SMX) and 287 ± 9 (PAR), in ultrapure water, and 47 ± 1 (SMX) and 407 ± 14 (PAR), in wastewater, while for CAC, the lowest and highest qm were 118 ± 7 (SMX) and 190 ± 16 (PAR) in ultrapure water and 123 ± 5 (SMX) and 160 ± 7 (CBZ) in wastewater. It was found that the matrix pH played a key role in these differences by controlling the surface electrostatic interactions between pharmaceutical and AC. Overall, it was evidenced the need of adsorption results in real matrices and demonstrated that AAC is a promising option to be implemented in tertiary wastewater treatments for pharmaceuticals' removal. Graphical abstract Production of an alternative activated carbon (AC) comparing favourably with a commercial AC in the removal of neutral and positive pharmaceuticals from wastewater.

Obtaining granular activated carbon from paper mill sludge - A challenge for application in the removal of pharmaceuticals from wastewater.

In this work, a granular activated carbon (GAC) was produced using primary paper mill sludge (PS) as raw material and ammonium lignosulfonate (AL) as binder agent. PS is a residue from the pulp and paper industry and AL is a by-product of the cellulose pulp manufacture and the proposed production scheme contributes for their valorisation together with important savings in GAC precursors. The produced GAC (named PSA-PA) and a commercially available GAC (GACN), used as reference material, were physically and chemically characterized. Then, these materials were tested in batch experiments for the adsorption of carbamazepine (CBZ), sulfamethoxazole (SMX), and paroxetine (PAR) from ultra-pure water and wastewater. Even though GACN and PSA-PA possess very similar specific surface areas (SBET) (629 and 671 m2 g-1, respectively), PSA-PA displayed lower maximum adsorption capacities (qm) than GACN for the pharmaceuticals here studied (6 ±â€¯1-44 ±â€¯5 mg g-1 and 49 ±â€¯6-106 ±â€¯40 mg g-1, respectively). This may be related to the comparatively higher incidence of mesopores in GACN, which might have positively influenced its adsorptive performance. Moreover, the highest hydrophobic character and degree of aromaticity of GACN could also have contributed to its adsorption capacity. On the other hand, the performance of both GACs was significantly affected by the matrix in the case of CBZ and SMX, with lower qm in wastewater than in ultra-pure water. However, the adsorption of PAR was not affected by the matrix. Electrostatic interactions and pH effects might also have influenced the adsorption of the pharmaceutical compounds in wastewater.

Production of highly efficient activated carbons from industrial wastes for the removal of pharmaceuticals from water-A full factorial design.

The wide occurrence of pharmaceuticals in aquatic environments urges the development of cost-effective solutions for their removal from water. In a circular economy context, primary paper mill sludge (PS) was used to produce activated carbon (AC) aiming the adsorptive removal of these contaminants. The use of low-cost precursors for the preparation of ACs capable of competing with commercial ACs continues to be a challenge. A full factorial design of four factors (pyrolysis temperature, residence time, precursor/activating agent ratio, and type of activating agent) at two levels was applied to the production of AC using PS as precursor. The responses analysed were the yield of production, percentage of adsorption for three pharmaceuticals (sulfamethoxazole, carbamazepine, and paroxetine), specific surface area (SBET), and total organic carbon (TOC). Statistical analysis was performed to evaluate influencing factors in the responses and to determine the most favourable production conditions. Four ACs presented very good responses, namely on the adsorption of the pharmaceuticals under study (average adsorption percentage around 78%, which is above that of commercial AC), and SBET between 1389 and 1627 m2 g-1. A desirability analysis pointed out 800 °C for 60 min and a precursor/KOH ratio of 1:1 (w/w) as the optimal production conditions.

Waste-based alternative adsorbents for the remediation of pharmaceutical contaminated waters: Has a step forward already been taken?

When adsorption is considered for water treatment, commercial activated carbon is usually the chosen adsorbent for the removal of pollutants from the aqueous phase, particularly pharmaceuticals. In order to decrease costs and save natural resources, attempts have been made to use wastes as raw materials for the production of alternative carbon adsorbents. This approach intends to increase efficiency, cost-effectiveness, and also to propose an alternative and sustainable way for the valorization/management of residues. This review aims to provide an overview on waste-based adsorbents used on pharmaceuticals' adsorption. Experimental facts related to the adsorption behaviour of each adsorbent/pharmaceutical pair and some key factors were addressed. Also, research gaps that subsist in this research area, as well as future needs, were identified. Simultaneously, this review aims to clarify the current status of the research on pharmaceuticals' adsorption by waste-based adsorbents in order to recognize if the right direction is being taken.

Single and multi-component adsorption of psychiatric pharmaceuticals onto alternative and commercial carbons.

This work describes the adsorptive removal of three widely consumed psychiatric pharmaceuticals (carbamazepine, paroxetine and oxazepam) from ultrapure water. Two different adsorbents were used: a commercial activated carbon and a non-activated waste-based carbon (PS800-150-HCl), produced by pyrolysis of primary paper mill sludge. These adsorbents were used in single, binary and ternary batch experiments in order to determine the adsorption kinetics and equilibrium isotherms of the considered pharmaceuticals. For the three drugs and both carbons, the equilibrium was quickly attained (with maximum equilibrium times of 15 and 120 min for the waste-based and the commercial carbons, respectively) even in binary and ternary systems. Single component equilibrium data were adequately described by the Langmuir model, with the commercial carbon registering higher maximum adsorption capacities (between 272 ± 10 and 493 ± 12 µmol g-1) than PS800-150-HCl (between 64 ± 2 and 74 ± 1 µmol g-1). Multi-component equilibrium data were also best fitted by the single component Langmuir isotherm, followed by the Langmuir competitive model. Overall, competitive effects did not largely affect the performance of both adsorbents. Binary and ternary systems maintained fast kinetics, the individual maximum adsorption capacities were not lower than half of the single component systems and both carbons presented improved total adsorption capacities for multi-component solutions.

Sludge from paper mill effluent treatment as raw material to produce carbon adsorbents: An alternative waste management strategy.

Pulp and paper industry produces massive amounts of sludge from wastewater treatment, which constitute an enormous environmental challenge. A possible management option is the conversion of sludge into carbon-based adsorbents to be applied in water remediation. For such utilization it is important to investigate if sludge is a consistent raw material originating reproducible final materials (either over time or from different manufacturing processes), which is the main goal of this work. For that purpose, different primary (PS) and biological sludge (BS) batches from two factories with different operation modes were sampled and subjected to pyrolysis (P materials) and to pyrolysis followed by acid washing (PW materials). All the materials were characterized by proximate analysis, total organic carbon (TOC) and inorganic carbon (IC), attenuated total reflectance Fourier transform infrared spectroscopy (ATR-FTIR) and N2 adsorption isotherms (specific surface area (SBET)and porosity determination). Sludge from the two factories proved to have distinct physicochemical properties, mainly in what concerns IC. After pyrolysis, the washing step was essential to reduce IC and to considerably increase SBET, yet with high impact in the final production yield. Among the materials here produced, PW materials from PS were those having the highest SBET values (387-488 m2 g-1). Overall, it was found that precursors from different factories might originate final materials with distinct characteristics, being essential to take into account this source of variability when considering paper mill sludge as a raw material. Nevertheless, for PS, low variability was found between batches, which points out to the reliability of such residues to be used as precursors of carbon adsorbents.

Removal of fluoxetine from water by adsorbent materials produced from paper mill sludge.

In this work, three adsorbents were produced by using as precursor primary paper mill sludge and applying KOH, NaOH or ZnCl2 as chemical activating agents (PS800-10KOH, PS800-10NaOH and PS800-10ZnCl2) and subjected to pyrolysis. The produced materials were tested for removal of fluoxetine from water, reported as one of the most persistent pharmaceuticals in the aquatic environment. Also, primary sludge pyrolysed under the same conditions but without activation (PS800-10) and a commercial activated carbon (PBFG4) were studied for comparison. Physical and chemical properties of the materials were determined and adsorption kinetic and equilibrium studies were performed in batch experiments. Equilibrium studies allowed testing the capacity of the produced materials for adsorb fluoxetine-HCl, showing no apparent correlation between the S(BET) areas and the adsorption capacities of the materials. The maximum adsorption capacity (mg g(-1)) was of 191.6±4.8 for PS800-10KOH; 136.6±9.6 for PS800-10NaOH; 28.4±0.3 for PS800-10ZnCl2; 120.4±2.5 for PS800-10 and 96.2±1.0 for PBFG4. It was demonstrated that many factors influence the removal of fluoxetine from solution and that the surface area is not the main factor in the process. Also the activation process did not enhance the properties of the produced materials.