ABSTRACT
The paper presents research on multicomponent glasses obtained from natural and secondary raw materials, i.e., basalt, amphibolite, and cullet. The raw materials were used as potential sets to produce mineral fibres or glass-ceramic materials. FTIR spectroscopy and XRD studies were carried out to identify the composition of the phase type in the glass sets. The results were supported by SEM-EDS microstructural studies of the obtained materials. The ability of the melts to crystallize and their basic properties required in producing mineral fibres, i.e., the hardness and the acidity modulus, were also determined. In the glass samples after the crystallization process, the spectroscopic studies revealed an increase in the half-width of the band at 1200-800 cm-1 and splitting at the values of about 870 cm-1 and 970 cm-1. These changes probably indicate the formation of pyroxene-type crystalline phases. Moreover, based on the XRD results, it was confirmed that the obtained materials were fully amorphous. After annealing at 800 °C for 2 h, the materials show a small proportion of crystalline phases. For the materials annealed at higher temperatures, clear peaks from the crystalline phases were represented mainly by pyroxenes. The proportion of crystalline phases in the samples was also found to rise with increasing temperature, and the hardness values for the basalt glasses and glasses after crystallization rose from 753 to 946 HV0.05. Such an effect positively affects the properties of the obtained glass-ceramic materials based on the proposed sets. However, in the case of mineral fibres, crystallization at early 2 h at 800 °C can be a disadvantageous feature from the point of view of their application because crystalline phases can lead to fibre damage after a short period of operation; this will be confirmed in this study.
ABSTRACT
The structure and properties of the glass can be modified by introducing appropriate additives. Dolomite is one of the primary raw materials modifying the properties of glass, in which the essential component is calcium-magnesium double carbonate CaCO3âMgCO3. The paper presents the research results on glasses obtained by smelting pure amphibolite and amphibolite modified with 10 and 20% dolomite additives. The raw material used was mined in the Poland region of Lower Silesia. The glass melting process was carried out in an electric furnace at 1450 °C for 2 h. The structure and properties of the glasses and crystallization products were determined by Differential Scanning Calorimetry (DSC), X-ray Diffraction (XRD), Fourier Transform Infrared Spectroscopy (FTIR) and Scanning Electron Microscopy-Energy Dispersive Spectroscopy (SEM-EDS). Viscosity and Vickers microhardness were also measured. It was found that the modification of amphibolite glass by adding dolomite affects the glasses' properties and structure. The research results determined the effect of dolomite addition on the properties of alumino-silicate glasses in terms of the mineral fibre products used in the construction industry.
ABSTRACT
Riveted joints are a common way to connect elements and subassemblies in the automotive industry. In the assembly process, tubular rivets are loaded axially with ca. 3 kN forces, and these loads can cause cracks and delamination in the rivet material. Such effects at the quality control stage disqualify the product in further assembly process. The article presents an analysis of the fracture mechanism of E215 low-carbon steel tubular rivets used to join modules of driver and passenger safety systems (airbags) in vehicles. Finite element method (FEM) simulation and material testing were used to verify the stresses and analysis of the rivet fracture. Numerical tests determined the state of stress during rivet forming using the FEM-EA method based on the explicit integration of central differences. Light microscopy (LM), scanning electron microscopy (SEM) and chemical composition analysis (SEM-EDS) were performed to investigate the microstructure of the rivet material and to analyze the cracks. Results showed that the cause of rivet cracking is the accumulation and exceeding of critical tensile stresses in the rivet flange during the tube processing and the final riveting (forming) process. Moreover, it was discovered that rivet fracture is largely caused by structural defects (tertiary cementite Fe,Mn3CIII along the boundaries of prior austenite grains) in the material resulting from the incorrectly selected parameters of the final heat treatment of the prefabricate (tube) from which the rivet was produced. The FEM simulation of the riveting and structural characterization results correlated well, so the rivet forming process and fracture mechanism could be fully investigated.
ABSTRACT
The metal-ceramic interface requires proper surface preparation of both metal and ceramic substrates. This process is complicated by the differences in chemical bonds and physicochemical properties that characterise the two materials. However, adequate bond strength at the interface and phase composition of the titanium-bioceramics system is essential for the durability of dental implants and improving the substrates' functional properties. In this paper, the authors present the results of a study determining the effect of mechanical and chemical surface treatment (sandblasting and etching) on the strength and quality of the titanium-low-fusing dental porcelain bond. To evaluate the strength of the metal-ceramic interface, the authors performed mechanical tests (three-point bending) according to EN ISO 9693 standard, microscopic observations (SEM-EDS), and Raman spectroscopy studies. The results showed that depending on the chemical etching medium used, different bond strength values and failure mechanisms of the metal-ceramic system were observed. The analyzed samples met the requirements of EN ISO 9693 for metal-ceramic systems and received strength values above 25 MPa. Higher joint strength was obtained for the samples after sandblasting and chemical etching compared to the samples subjected only to sandblasting.
ABSTRACT
BACKGROUND: As arterial myocardial revascularization is proved to provide great results, radial artery use as a graft and its consequences remain an important issue. OBJECTIVES: The aim of the study was to evaluate how patients assess their forearm and hand function after radial artery harvest for coronary artery bypass grafting (CABG). METHODS: 50 patients (mean age 52.2 ± 7.4 years) who underwent CABG at least 6 months (median follow up 11.75 months) earlier filled in a questionnaire concerning hand and forearm efficiency and discomfort. RESULTS: The global efficiency of the operated upper extremity was scored mean 8.87 ± 1.26 points on a 10-point scale and it was worse in patients who noticed at least one sort of disorder than in patients with no problems (8.6 ± 1.4 versus 9.4 ± 0.7 points; P = .04). Paresthesias were the most often reported disorders; 21 patients felt some tingling and/or numbness, but in only 14 (28%) could the symptoms be considered as related to the operation. 20 patients (40%) declared that they felt some scar-related discomfort. Reduced grip strength and excessive hand fatigue were reported by 20% and 10% of patients, respectively. None of those interviewed answered that symptoms reported affected his or her life activity on any level. CONCLUSION: The hand and forearm efficiency after radial artery harvest for CABG was highly evaluated by the majority of patients. Despite the fact that many patients reported some surgery-related problems, they did not notice extremity dysfunction that could limit their life activity.
