PEDOT:PSS Conductivity Enhancement through Addition of the Surfactant Tween 80.

Replacement of indium tin oxide with the intrinsically conducting polymer poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) has been of significant interest in recent years as a result of lower processing and material costs. In addition, the inclusion of additives has been reported to further enhance the conductivity, rheology, and wettability of PEDOT:PSS. In this study, Tween 80 was shown to decrease the sheet resistance of PEDOT:PSS films from approximately 1000 to 76 Ω□-1 at a 2.67 wt% surfactant concentration. Through X-ray diffraction, Raman spectroscopy, and atomic force microscopy, it was shown that the surfactant caused phase separation and structural ordering of the PEDOT and PSS components, leading to this improvement in conductivity. Furthermore, Tween 80 altered the rheological properties and decreased the surface tension of PEDOT:PSS, making coating common commodity polymers, often used as flexible substrates, more viable.

Effect of µPlasma Modification on the Wettability and the Ageing Behaviour of Glass Fibre Reinforced Polyamide 6 (GFPA6).

Glass fibre reinforced polyamide 6 (GFPA6) thermoplastic composites (TPCs) are promising materials with excellent properties, but due to their low surface free energy they are usually difficult to wet, and therefore, possesses poor adhesion properties. µPlasma modification offers potential solutions to this problem through functionalisation of the GFPA6 surface. In this study, the effect of µPlasma on the wetting behaviour of GFPA6 surfaces was investigated. Following single µPlasma treatment scans of GFPA6 samples, a substantial enhancement in wettability was observed. However, the effect of the µPlasma modification was subject to an ageing (hydrophobic recovery) phenomenon, although the enhancement was still partially maintained after 4 weeks. The ageing process was slower when the GFPA6 material was pre-dried and stored in low humidity conditions, thereby demonstrating the importance of the storage environment to the rate of ageing. Orientation of the fibres to the observed contact angle was found to be crucial for obtaining reproducible measurements with lower deviation. The influence of testing liquid, droplet volume and surface texture on the repeatability of the measured contact angle were also investigated.

Clinical impact of magnetic resonance imaging distortions on gamma knife radiosurgery.

INTRODUCTION: Magnetic resonance imaging (MRI) is the preferred imaging modality for Leksell Gamma Knife® (LGK) stereotactic radiosurgery (SRS) treatment planning (TP) due to superior soft tissue definition compared to computed tomography (CT). However, inherent distortions in MRI can affect treatment accuracy. The aim of this study was to develop a model to visualise the effect of MRI distortion on LGK SRS target coverage. METHODS: A model was developed using MR images of a QUASARTM GRID3D QA phantom. One hundred and twenty-five points were compared against known phantom geometry. Using linear interpolation, the model was applied retrospectively to 10 brain metastases patient data sets treated with LGK. The model estimated the corrected shot position accounting for distortion. A total of 44 metastases were investigated regarding the effects of MRI distortion on target coverage. RESULTS: The model indicated significantly reduced mean error by 0.30 mm and variance by 0.09 mm (P = 0.008). After model application, 23 (53%) metastases showed reduced coverage. Six of the 23 metastases were deemed to be potentially clinically significant changes. Results indicated MRI distortion had a greater effect on smaller targets (mean 0.06cc) located further away from the image isocentre (mean 64.88 mm). CONCLUSION: This study developed a model to visualise the effect of MRI distortion on LGK SRS target coverage. Results suggest that MRI distortion can affect target coverage and the developed model may be one method to assess its impact. These results indicate that MRI distortion may have a greater effect on smaller targets located at the image periphery.

The Effect of a Secondary Process on the Analysis of Isothermal Crystallisation Kinetics by Differential Scanning Calorimetry.

This paper demonstrates the application of a modified Avrami equation in the analysis of crystallisation curves obtained using differential scanning calorimetry (DSC). The model incorporates a square root of time dependence of the secondary process into the conventional Avrami equation and, although previously validated using laser flash analysis and infrared spectroscopy, is not currently transferable to DSC. Application of the model to calorimetric data required long-duration isotherms and a series of data treatments. Once implemented, the square root of time dependence of the secondary process was once again observed. After separation of the secondary process from the primary, a mechanistic n value of 3 was obtained for the primary process. Kinetic parameters obtained from the analysis were used in the model to regenerate the fractional crystallinity curves. Comparison of the model with experimental data generated R2 values in excess of 0.995. Poly(3-hydroxybutyrate-co-3-hydroxyvalerate) was used as model polymer due to the prominent secondary crystallisation behaviour that this polymer is known to display.

Crosslinker Copolymerization for Property Control in Inverse Vulcanization.

Sulfur is an underused by-product of the petrochemicals industry. Recent research into inverse vulcanization has shown how this excess sulfur can be transformed into functional polymers, by stabilization with organic crosslinkers. For these interesting new materials to realize their potential for applications, more understanding and control of their physical properties is needed. Here we report four new terpolymers prepared from sulfur and two distinct alkene monomers that can be predictively tuned in glass transition, molecular weight, solubility, mechanical properties, and color.

Formulation of a covalently bonded hydroxyapatite and poly(ether ether ketone) composite.

Spinal fusion devices can be fabricated from composites based on combining hydroxyapatite and poly(ether ether ketone) phases. These implants serve as load-bearing scaffolds for the formation of new bone tissue between adjacent vertebrae. In this work, we report a novel approach to covalently bond hydroxyapatite and poly(ether ether ketone) to produce a novel composite formulation with enhanced interfacial adhesion between phases. Compared to non-linked composites (HA_PEEK), covalently linked composites (HA_L_PEEK), loaded with 1.25 vol% hydroxyapatite, possessed a greater mean flexural strength (170 ± 5.4 vs 171.7 ± 14.8 MPa (mean ± SD)) and modulus (4.8 ± 0.2 vs 5.0 ± 0.3 GPa (mean ± SD)). Although the mechanical properties were not found to be significantly different (p > 0.05), PEEK_L_HA contained substantially larger hydroxyapatite inclusions (100-1000 µm) compared to HA_PEEK (50-200 µm), due to the inherently agglomerative nature of the covalently bonded hydroxyapatite and poly(ether ether ketone) additive. Larger inclusions would expectedly weaken the HA_L_PEEK composite; however, there is no significant difference between the flexural modulus of poly(ether ether ketone) with respect to HA_L_PEEK (p = 0.13). In addition, the flexural modulus of HA_PEEK is significantly lower compared to poly(ether ether ketone) (p = 0.03). Ultimately, covalent linking reduces hydroxyapatite particulate de-bonding from the polymeric matrix and inhibits micro-crack development, culminating in enhanced transfer of stiffness between hydroxyapatite and poly(ether ether ketone) under loading.

Wearable Sensor Technology Efficacy in Peripheral Vascular Disease (wSTEP): A Randomized Controlled Trial.

OBJECTIVE: To evaluate the effect of using wearable activity monitors (WAMs) in patients with intermittent claudication (IC) within a single-center randomized controlled trial. BACKGROUND: WAMs allow users to set daily activity targets and monitor their progress. They may offer an alternative treatment to supervised exercise programs (SEPs) for patients with IC. METHODS: Thirty-seven patients with IC were recruited and randomized into intervention or control group. The intervention consisted of a feedback-enabled, wrist-worn activity monitor (WAM) in addition to access to SEP. The control group was given access to SEP only. The outcome measures were maximum walking distance (MWD), claudication distance (CD), and quality of life as measured by the VascuQol questionnaire. Participants were assessed upon recruitment, and at 3, 6, and 12 months. RESULTS: Patients in the WAM group showed significant improvement in MWD at 3 and 6 months (80-112 m, to 178 m; P < 0.001), which was sustained at 12 months. The WAM group also increased CD (40 vs 110 m; P < 0.001) and VascuQol score (4.7 vs 5.8; P = 0.004). The control group saw a temporary increase in VascuQol score at 6 months (4.5 vs 4.7; P = 0.028), but no other improvements in MWD or CD were observed. Significantly higher improvements in MWD were seen in the WAM group compared with that in the control group at 6 months (82 vs -5 m; P = 0.009, r = 0.47) and 12 months (69 vs 7.5 m; P = 0.011, r = 0.52). CONCLUSIONS: The study demonstrates the significant, sustained benefit of WAM-led technologies for patients with IC. This potentially resource-sparing intervention is likely to provide a valuable adjunct or alternative to SEP.

Thermosensitive hydrogel as an in situ gelling antimicrobial ocular dressing.

Microbial keratitis is a severe ocular condition and one of the most prevalent causes of corneal scarring and associated blindness worldwide. Risk factors include contact lens use, ocular trauma, ocular surface disease and immunosuppression. Initial clinical management mandates intensive (hourly or more frequent) topical administration of broad spectrum antimicrobial therapy for at least 48h, which may require hospital admission, followed by tailored therapy based on microbiological investigation and the institution of strategies to reduce inflammation and promote healing. In this work we report an ocular wound dressing which can encapsulate and give sustained release of different antibiotics. The use of this dressing would allow patients to have eye drops on a 4 hourly basis, thereby facilitating treatment compliance and reducing hospital admissions.

Development of a rapid method to isolate polyhydroxyalkanoates from bacteria for screening studies.

We describe a novel method of Polyhydroxyalkanoate (PHA) extraction using dimethyl sulphoxide (DMSO) for use in screening studies. Compared to conventional chloroform extraction, the DMSO method was shown to release comparable quantities of PHA from Cupriavidus necator cells, with comparable properties as determined using Fourier transform infrared spectroscopy and differential scanning calorimetry.

Active screen plasma surface modification of polycaprolactone to improve cell attachment.

To tailor polycaprolactone (PCL) surface properties for biomedical applications, film samples of PCL were surface modified by the active screen plasma nitriding (ASPN) technique. The chemical composition and structure were characterized by Fourier transform infrared spectroscopy and X-ray photoelectron spectroscopy. The wettability of the surface modified polymers was investigated by contact angle and surface energy methods. Biocompatibility of the prepared PCL samples was evaluated in vitro using MC3T3-E1 osteoblast-like cells. The degradability was assessed by determining the self-degradation rate (catalyzed by lipase). The results show that ASPN surface modification can effectively improve osteoblast cell adhesion and spreading on the surface of PCL. The main change in chemical composition is the exchange of some carboxyl groups on the surface for hydroxyl groups. The active-screen plasma nitriding technique has been found to be an effective and practical method to effectively improve osteoblast cell adhesion and spreading on the PCL surface. Such changes have been attributed to the increase in wettablity and generation of new hydroxyl groups by plasma treatment. After active-screen plasma treatment, the PCL film is still degradable, but the enzymatic degradation rate is slower compared with untreated PCL film.

Effect of sterilisation by gamma irradiation on the ability of polycaprolactone (PCL) to act as a scaffold material.

This paper investigates the effect of sterilisation by gamma irradiation (dose 2.5Mrad) on the following properties of polycaprolactone (PCL): (1) degradation rate (catalysed by lipase), (2) mechanical properties, (3) the ability of cells to attach and subsequently grow on its surface. Gel permeation chromatography (GPC) was used to determine the effects of gamma irradiation of weight average (M(w)) and number average (M(n)) molecular weights. Gamma irradiation significantly decreased the rate of degradation, although the rates depended on the initial mass of polymer; it also affected the appearance of the degraded specimens when they were examined by scanning electron microscopy. Irradiation also significantly increased the mechanical yield stress but not the failure stress of PCL. It caused a significant increase in M(w) and decrease in M(n) that could be attributed to chain scission and cross-linking. Chondrocyte attachment and growth on PCL was not significantly affected by gamma irradiation.

Polyhydroxybutyrate accumulation by a Serratia sp.

A strain of Serratia sp. showed intracellular electron-transparent inclusion bodies when incubated in the presence of citrate and glycerol 2-phosphate without nitrogen source following pre-growth under carbon-limitation in continuous culture. About 1.3 mmol citrate were consumed per 450 mg biomass, giving a calculated yield of maximally 55% of stored material per g of biomass dry wt. The inclusion bodies were stained with Sudan Black and Nile Red (NR), suggesting a lipid material, which was confirmed as polyhydroxybutyrate (PHB) by analysis of molecular fragments by GC and by FTIR spectroscopy of isolated bio-PHB in comparison with reference material. Multi-parameter flow cytometry in conjunction with NR fluorescence, and electron microscopy, showed that not all cells contained heavy PHB bodies, suggesting the potential for increasing the overall yield. The economic attractiveness is enhanced by the co-production of nanoscale hydroxyapatite (HA), a possible high-value precursor for bone replacement materials.