Comparison of multiforce nickel-titanium wires to multistrand wires without force zones in bending and torque measurements.

PURPOSE: The aim was to compare rectangular multiforce nickel-titanium (NiTi) wires to rectangular wires with only one force zone. Both types of wires are primarily intended for use during the levelling phase of orthodontic treatment. Thus, basic mechanical properties were examined by means of a three-point bending test. Torque expression, which is dependent on both wire parameters and interslot distances, was analyzed using the Orthodontic Measurement and Simulation System (OMSS). MATERIAL/METHODS: Four multizone products were tested: DuoForce™ (Forestadent, Pforzheim, Germany), TriTanium™ (American Orthodontics, Sheboygan, WI, USA), Triple Force™ (ODS, Kisdorf, Germany), Bio-Active™ (GC, Breckerfeld, Germany), and two multistrand products without force zones: a nine-strand NiTi, TurboWire™ (Ormco, Orange, CA, USA) and an eight-strand stainless steel (SS) wire, Multibraid™ (GAC, Dentsply Sirona, York, PA, USA). All the wires had the dimension 0.40 mmâ€¯× 0.56 mm (0.016 inchâ€¯× 0.022 inch) except the nine-strand NiTi wire TurboWire™, which had a dimension of 0.43 mmâ€¯× 0.65 mm (0.017 inchâ€¯× 0.025 inch). Six different bracket systems in the 0.018 inch slot system were chosen: the conventional brackets discovery® and discovery® smart (Dentaurum, Ispringen, Germany), the active self-ligating brackets InOvation™ and InOvation™ mini (GAC, Dentsply Sirona, York, PA, USA) and the passive self-ligating brackets Carrière™ (ODS, Kisdorf, Germany) and BioPassive® (Forestadent, Pforzheim, Germany). The first set-up was a three-point bending test according to DIN EN ISO 15841. For the second experiment, the bracket products glued on a maxilla model were combined with the wire products. The torque moments arising during torqueing of the wires between +20° and -20° were measured in three positions: first incisor, canine and second bicuspid. RESULTS: Bending tests confirmed variation of the force corresponding to the force zones. The nine-strand NiTi wire TurboWireTM and the eight-strand SS wire Multibraid™ did not show any variation dependent on the tested area. Torque-moments generated by the multizone wires were higher compared to the braided wires. The nine-strand NiTi wire showed the lowest moments in spite of the higher dimension. As expected, increasing the interbracket distance reduced the torque moments. CONCLUSION: The tests verified the existence of multiple force zones in the NiTi wires for forces and moments, respectively. As the torque-moments arising from the multizone wires were rather high, it is not recommended to use these wires as a first "leveling wire" in orthodontic treatment, especially in extremely crowded cases.

First order couples induced by nickel-titanium archwires featuring an electrochemically refined surface during simulated rotation of teeth.

OBJECTIVE: The significance of friction inside the bracket-wire-ligature interface remains controversial despite having been investigated for four decades. Numerous approaches have been proposed to reduce friction via any of the elements of the interface, key among them being recently developed bracket modifications and the introduction of surface-modified wires. The present study explored whether archwires treated by a novel electrochemical process of surface refinement influence first-order couples generated inside self-ligating and conventionally ligated brackets during tooth rotation. MATERIALS AND METHODS: A surface-refined nickel-titanium archwire (OptoTherm/LoFrix™) was compared ex vivo to a non-refined archwire of the same production lot (OptoTherm™), the nominal dimensions being 0.014×0.025'' in both cases. Three bracket designs were included to assess the role of the ligation mechanism: (1) Carrière SLB™ passive self-ligating brackets, (2) BioQuick® active self-ligating brackets, and (3) Classic Series® conventionally ligated brackets. The brackets were bonded to leveled tooth elements on a resin mandibular arch. To simulate rotation, the lower left first premolar was removed and connected to a biomechanical measuring system. The simulation procedures were performed at 37°C. RESULTS: The various bracket designs yielded characteristic torque curves mainly reflecting the play of the archwire specimens inside their slots. While the passive self-ligating brackets exhibited 2-3° of play in either direction, both the active self-ligating brackets and the conventional brackets with elastic ligatures did not reveal any play. Torque levels ranged from 8 Nmm inside the conventional brackets to 13 Nmm inside the passive self-ligating brackets. The surface-refined archwires induced significantly (up to 35%) lower torque levels and were slightly reduced in cross-section. CONCLUSION: Electrochemical surface refinement can significantly reduce first order couples induced by archwires. This effect is caused by less friction, but also by the slightly reduced cross-section of these wires.