Development of Multiscale Composite with Hybrid Natural Nanofibers.

Natural nanofibers are widely used in the field of medicine, but the low strength of these nanofibers is one of the major concerns. A number of factors, importantly the composition, affect the strength of natural nanofibers. The purpose of the current study is to ascertain the effect of the composition of natural nanofibers on the strength of hybrid composites formed using these nanofibers. Hybrid composites formed using 32% volume glass fibre with optimized volume fraction of 0.5% of pure Cellulose Acetate (CA), and 0.5% CA + Hemp Seed (HS) for this study to carry out the analysis. Hybrid composites were produced with vacuum-assisted resin transfer molding (VARTM) by collecting natural nanofibers, produced using the electrospinning process, over glass fiber mats. The electrospinning process was carried out with 12 kV, 10 cm tip to the collector gap, and 12% concentration of the solution. The tensile strength of the hybrid composites was measured using the universal testing machine (UTM). The results showed that the diameter of the electrospun nanofiber varied between 50 and 1400 nm and was affected by solution concentration, voltage, tip-to-collector distance, flow rate, and inclusion of HS in CA. The inclusion of HS in CA, for all compositions, decreased the fiber diameter and caused the formation of beads prominently at higher concentrations. Hybrid composites formed from nanofibers produced using CA and HS showed higher elastic modulus (232 MPa) and tensile strength (20.4 GPa) as compared with nanofibers produced using CA only (elastic modulus = 110 MPa and 13.7 GPa).

In-situ neutron diffraction study of lattice deformation behaviour of commercially pure titanium at cryogenic temperature.

Titanium has a significant potential for the cryogenic industrial fields such as aerospace and liquefied gas storage and transportation due to its excellent low temperature properties. To develop and advance the technologies in cryogenic industries, it is required to fully understand the underlying deformation mechanisms of Ti under the extreme cryogenic environment. Here, we report a study of the lattice behaviour in grain families of Grade 2 CP-Ti during in-situ neutron diffraction test in tension at temperatures of 15-298 K. Combined with the neutron diffraction intensity analysis, EBSD measurements revealed that the twinning activity was more active at lower temperature, and the behaviour was complicated with decreasing temperature. The deviation of linearity in the lattice strains was caused by the load-redistribution between plastically soft and hard grain families, resulting in the three-stage hardening behaviour. The lattice strain behaviour further deviated from linearity with decreasing temperature, leading to the transition of plastically soft-to-hard or hard-to-soft characteristic of particular grain families at cryogenic temperature. The improvement of ductility can be attributed to the increased twinning activity and a significant change of lattice deformation behaviour at cryogenic temperature.

Fabrication and design of mechanically stable and free-standing polymeric membrane with two-level apertures.

Herein, we report the fabrication process and the investigation of mechanically stable, flexible and free-standing polymeric membranes with two-level apertures. By using overlapped oxygen inhibition layers (OILs) with variation in diameters of the micro-sized supporting layer, we successfully fabricated the mechanically stable and free-standing polymeric membrane with micro/nano two-level apertures. The nano aperture membrane was stably sustained on the micro aperture membrane with a diameter of 50 µm and 100 µm, but was torn off in the case of 300 µm and 500 µm sized supporting layers. To analyze the results, we propose a simple model to set the criteria of the geometrical features which are mechanically stable during the demolding process. It is worth noting that an appropriate material modulus, length, and thickness of the membrane are required for designing and achieving the robust free-standing hierarchical polymeric membrane.

Data on a new beta titanium alloy system reinforced with superlattice intermetallic precipitates.

The data presented in this article are related to the research article entitled "a new beta titanium alloy system reinforced with superlattice intermetallic precipitates" (Knowles et al., 2018) [1]. This includes data from the as-cast alloy obtained using scanning electron microscopy (SEM) and x-ray diffraction (XRD) as well as SEM data in the solution heat treated condition. Transmission electron microscopy (TEM) selected area diffraction patterns (SADPs) are included from the alloy in the solution heat treated condition, as well as the aged condition that contained < 100 nm B2 TiFe precipitates [1], the latter of which was found to exhibit double diffraction owing to the precipitate and matrix channels being of a similar width to the foil thickness (Williams and Carter, 2009) [2]. Further details are provided on the macroscopic compression testing of small scale cylinders. Of the micropillar deformation experiment performed in [1], SEM micrographs of focused ion beam (FIB) prepared 2 µm micropillars are presented alongside those obtained at the end of the in-situ SEM deformation as well as videos of the in-situ deformation. Further, a table is included that lists the Schmidt factors of all the possible slip systems given the crystal orientations and loading axis of the deformed micropillars in the solution heat treated and aged conditions.

High-energy transmission Laue micro-beam X-ray diffraction: a probe for intra-granular lattice orientation and elastic strain in thicker samples.

An understanding of the mechanical response of modern engineering alloys to complex loading conditions is essential for the design of load-bearing components in high-performance safety-critical aerospace applications. A detailed knowledge of how material behaviour is modified by fatigue and the ability to predict failure reliably are vital for enhanced component performance. Unlike macroscopic bulk properties (e.g. stiffness, yield stress, etc.) that depend on the average behaviour of many grains, material failure is governed by `weakest link'-type mechanisms. It is strongly dependent on the anisotropic single-crystal elastic-plastic behaviour, local morphology and microstructure, and grain-to-grain interactions. For the development and validation of models that capture these complex phenomena, the ability to probe deformation behaviour at the micro-scale is key. The diffraction of highly penetrating synchrotron X-rays is well suited to this purpose and micro-beam Laue diffraction is a particularly powerful tool that has emerged in recent years. Typically it uses photon energies of 5-25 keV, limiting penetration into the material, so that only thin samples or near-surface regions can be studied. In this paper the development of high-energy transmission Laue (HETL) micro-beam X-ray diffraction is described, extending the micro-beam Laue technique to significantly higher photon energies (50-150 keV). It allows the probing of thicker sample sections, with the potential for grain-level characterization of real engineering components. The new HETL technique is used to study the deformation behaviour of individual grains in a large-grained polycrystalline nickel sample during in situ tensile loading. Refinement of the Laue diffraction patterns yields lattice orientations and qualitative information about elastic strains. After deformation, bands of high lattice misorientation can be identified in the sample. Orientation spread within individual scattering volumes is studied using a pattern-matching approach. The results highlight the inability of a simple Schmid-factor model to capture the behaviour of individual grains and illustrate the need for complementary mechanical modelling.