Structured and gradient polymer brushes from biphenylthiol self-assembled monolayers by self-initiated photografting and photopolymerization (SIPGP).

The self-initiated photografting and photopolymerization (SIPGP) of styrene, methyl methacrylate, and tert-butyl methacrylate on structured self-assembled monolayers (SAMs) of electron beam cross-linked omega-functionalized biphenylthiols SAMs on gold was investigated. Polymer brushes with defined thickness can be prepared on crosslinked benzyl-, phenyl-, hydroxyl-, and amino-functionalized SAMs, whereas non-cross-linked SAM regions desorb from the surface during the SIPGP process. By the preparation of brush gradients on different functionalized SAMs, it was demonstrated that the resulting polymer brush layer thickness is determined by the locally applied electron beam dosage. Defined micro-nanostructured polymer brush patterns can be prepared down to a size of 50 nm. Finally, it was shown that polymer brushes obtained by the SIPGP process have a branched architecture.

pH-amplified exponential growth multilayers: a facile method to develop hierarchical micro- and nanostructured surfaces.

We report a direct method to amplify the exponential growth of multilayers significantly by the alternating deposition of polyethylenimine (PEI) at high pH and poly(acrylic acid) (PAA) at low pH. The alternating pH switches the degree of ionization of the polyelectrolytes in the multilayers, which enhances the diffusion of PEI into and out of the film and hence increases the deposited mass per cycle. The synergetic action of the pH-tunable charge density and diffusivity of the weak polyelectrolytes provides a new method for the enhanced growth of multilayers with hierarchal micro- and nanostructured surfaces.

The proteome of rat olfactory sensory cilia.

Olfactory sensory neurons expose to the inhaled air chemosensory cilia which bind odorants and operate as transduction organelles. Odorant receptors in the ciliary membrane activate a transduction cascade which uses cAMP and Ca(2+) for sensory signaling in the ciliary lumen. Although the canonical transduction pathway is well established, molecular components for more complex aspects of sensory transduction, like adaptation, regulation, and termination of the receptor response have not been systematically identified. Moreover, open questions in olfactory physiology include how the cilia exchange solutes with the surrounding mucus, assemble their highly polarized set of proteins, and cope with noxious substances in the ambient air. A specific ciliary proteome would promote research efforts in all of these fields. We have improved a method to detach cilia from rat olfactory sensory neurons and have isolated a preparation specifically enriched in ciliary membrane proteins. Using LC-ESI-MS/MS analysis, we identified 377 proteins which constitute the olfactory cilia proteome. These proteins represent a comprehensive data set for olfactory research since more than 80% can be attributed to the characteristic functions of olfactory sensory neurons and their cilia: signal processing, protein targeting, neurogenesis, solute transport, and cytoprotection. Organellar proteomics thus yielded decisive information about the diverse physiological functions of a sensory organelle.

Morphology control of structured polymer brushes.

The surface-initiated photopolymerization (SIPP) of vinyl monomers on structured self-assembled monolayers, as defined by two-dimensional (2D) initiator templates for polymer growth, is investigated. The 2D templates are prepared by electron-beam chemical lithography (EBCL) of 4'-nitro-4-mercaptobiphenyl (NBT) and chemical conversion to an asymmetric azo initiator (4'-azomethylmalonodinitrile-1,1'-biphenyl-4-thiol). Ex situ kinetic studies of the SIPP process reveal a linear increase in the thickness of the polymer layer with the irradiation/polymerization time. The effect of the applied electron dosage during the EBCL process upon the final thickness of the polymer layer is also studied. The correlation between the electron-induced conversion of the 4'-nitro to the 4'-amino group and the layer thickness of the resulting polymer brush indicates that the polymer-brush grafting density can be directly controlled by the EBCL process. NBT-based template arrays are used for the combinatorial study of the influence of the lateral structure size and the irradiation dosage on the morphology of the resulting polymer-brush layer. Analysis of the array topography reveals the dependence of the thickness of the dry polymer layer on both electron dosage and structure size. This unique combination of EBCL as a lithographic technique to locally manipulate the surface chemistry and SIPP to amplify the created differences allows the preparation of defined polymer-brush layers of controlled morphologies.

Fabrication of thermosensitive polymer nanopatterns through chemical lithography and atom transfer radical polymerization.

Micro- and nanopatterns of thermosensitive poly(N-isopropylacrylamide) brush on gold substrate were prepared by using chemical lithography combined with surface-initiated atom transfer radical polymerization. Self-assembled monolayers of 4'-nitro-1, 1'-biphenyl-4-thiol were structured by chemical lithography which produced cross-linked 4'-amino-1,1'-biphenyl-4-thiol monolayer within a nitro-terminated matrix. The terminal amino groups in monolayers were bounded with the surface initiator bromoisobutyryl bromide. After polymerization, the smallest size can reach to 70-nm line width and dots. The thermosensitivity of poly(N-isopropylacrylamide) brushes is demonstrated by contact angle measurement and fluid atomic force microscopy. This fabrication approach allows creating spatially defined polymer patterns and provides a simple and versatile method to construct complex micro- and nanopatterned polymer brushes with spatial and topographic control in a single step.

Nanostructured polymer brushes.

Nanopatterned polymer brushes with sub-50-nm resolution were prepared by a combination of electron-beam chemical lithography (EBCL) of self-assembled monolayers (SAMs) and surface-initiated photopolymerization (SIPP). As a further development of our previous work, selective EBCL was performed with a highly focused electron beam and not via a mask, to region-selectively convert a SAM of 4'-nitro-1,1'-biphenyl-4-thiol to defined areas of crosslinked 4'-amino-1,1'-biphenyl-4-thiol. These "written" structures were then used to prepare surface-bonded, asymmetric, azo initiator sites of 4'-azomethylmalonodinitrile-1,1'-biphenyl-4-thiol. In the presence of bulk styrene, SIPP amplified the primary structures of line widths from 500 to 10 nm to polystyrene structures of line widths 530 nm down to approximately 45 nm at a brush height of 10 or 7 nm, respectively, as measured by scanning electron microscopy and atomic force microscopy (AFM). The relative position of individual structures was within a tolerance of a few nanometers, as verified by AFM. At line-to-line spacings down to 50-70 nm, individual polymer brush structures are still observable. Below this threshold, neighboring structures merge due to chain overlap.

Self-assembled molecular pattern by chemical lithography and interfacial chemical reactions.

The fabrication of lipid-modified molecular patterns by Chemical Lithography combined with interfacial chemical reactions is reported. In this method, self-assembled monolayers (SAMs) of 4'-nitro-1,1'-biphenyl-4-thiol (NBT) were structured by Chemical Lithography which produced cross-linked 4'-amino-1,1'-biphenyl-4-thiol (cABT) monolayers within a nitro-terminated (NBT) matrix. The terminal amino groups in the cABT monolayer were diazotized to create diazo cations, and the lipid monolayer with negative charge was assembled on the diazo regions by electrostatic attraction. Under the exposure of UV light, the photoreaction occurs. The diazonium groups interacting with the lipid headgroups via electrostatic attraction decompose and release N2 which leads to the lipid monolayer covalently attaching to the cABT region. The presence of phosphorus in X-ray photoelectron spectra (XPS) reveals the binding of the phospholipid layer to the cABT surface. Atomic force microscopy (AFM) images display that lipid-modified molecular patterns with different sizes and shapes and with a thickness of ca. 2.5 nm have been formed. The resulting lipid-modified molecular patterns are considered to be a first step towards obtaining stable biointerfacing patterns and studying biomolecular recognition.