Evaluation of Physicochemical Properties of a Hydroxyapatite Polymer Nanocomposite for Use in Fused Filament Fabrication.

Over the last decade, there has been an increasing interest in the use of bioceramics for biomedical purposes. Bioceramics, specifically those made of calcium phosphate, are commonly used in dental and orthopaedic applications. In this context, hydroxyapatite (HA) is considered a viable option for hard tissue engineering applications given its compositional similarity to bioapatite. However, owing to their poor mechanobiology and biodegradability, traditional HA-based composites have limited utilisation possibilities in bone, cartilage and dental applications. Therefore, the efficiency of nano HA (nHA) has been explored to address these limitations. nHA has shown excellent remineralising effects on initial enamel lesions and is widely used as an additive for improving existing dental materials. Furthermore, three-dimensional printing (3DP) or fused deposition modelling that can be used for creating dental and hard tissue scaffolds tailored to each patient's specific anatomy has attracted considerable interest. However, the materials used for producing hard tissue with 3DP are still limited. Therefore, the current study aimed to develop a hybrid polymer nanocomposite composed of nHA, nanoclay (NC) and polylactic acid (PLA) that was suitable for 3DP. The nHA polymer nanocomposites were extruded into filaments and their physiochemical properties were evaluated. The results showed that the addition of nHA and NC to the PLA matrix significantly increased the water absorption and contact angle. In addition, the hardness increased from 1.04 to 1.25 times with the incorporation of nHA. In sum, the nHA-NC-reinforced PLA could be used as 3DP filaments to generate bone and dental scaffolds, and further studies are needed on the biocompatibility of this material.

Rose Petal Mimetic Surfaces with Antibacterial Properties Produced Using Nanoimprint Lithography.

In this study, we produced bioinspired micro/nanotopography on the surface of poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP) films and demonstrated that these films display antibacterial properties. In the first step, structures that are found on the surface of a rose petal were copied on the surface of PVDF-HFP films. Following this, a hydrothermal method was used to grow ZnO nanostructures on top of this rose petal mimetic surface. The antibacterial behavior of the fabricated sample was demonstrated against Gram-positive Streptococcus agalactiae (S. agalactiae) and Gram-negative Escherichia coli (E. coli) as model bacteria. For comparison purposes, the antibacterial behavior of a neat PVDF-HFP film was also investigated against both bacterial species. The results show that the presence of rose petal mimetic structures on PVDF-HFP helped the material to display improved antibacterial performance against both S. agalactiae and E. coli compared to the antibacterial performance of neat PVDF-HFP. The antibacterial performance was further enhanced for samples that had both rose petal mimetic topography and ZnO nanostructures on the surface.

Simulation of Wood Polymer Composites with Finite Element Analysis.

Wood is a cellulosic material that is most abundantly available in nature. Wood has been extensively used as reinforcement in polymer composite materials. Wood polymer composite (WPC) is an environmentally friendly and sustainable material exploited in building and construction within the marine, packaging, housewares, aerospace, and automotive industries. However, the precision of testing equipment for finding the properties of WPCs becomes less feasible compared to experimental analysis due to a high degree of differences in the measurement of properties such as stress, strain and deformation. Thus, evaluating the mechanical properties of WPCs using finite element analysis (FEA) can aid in overcoming the inadequacies in measuring physical properties prior to experimental analyses. Furthermore, the prediction of mechanical properties using simulation tools has evolved to analyze novel material performance under various conditions. The current study aimed to examine the mechanical properties of saw dust-reinforced recycled polypropylene (rPP) through experimentation and FEA. A model was developed using SolidWorks, and simulation was performed in ANSYS to predict the mechanical properties of the WPCs. To validate the obtained results, the simulated static tension test results were confirmed with experimental tension tests, and both assessments were well in accordance with each other. Using FEA to predict material properties could be a cost-effective technique in studying new materials under varied load conditions.

Development of Biodegradable Composites Using Polycaprolactone and Bamboo Powder.

The use of biodegradable polymers in daily life is increasing to reduce environmental hazards. In line with this, the present study aimed to develop a fully biodegradable polymer composite that was environmentally friendly and exhibited promising mechanical and thermal properties. Bamboo powder (BP)-reinforced polycaprolactone (PCL) composites were prepared using the solvent casting method. The influence of BP content on the morphology, wettability, and mechanical and thermal properties of the neat matrix was evaluated. In addition, the degradation properties of the composites were analysed through soil burial and acidic degradation tests. It was revealed that BP contents had an evident influence on the properties of the composites. The increase in the BP content has significantly improved the tensile strength of the PCL matrix. A similar trend is observed for thermal stability. Scanning electron micrographs demonstrated uniform dispersion of the BP in the PCL matrix. The degradation tests revealed that the biocomposites with 40 wt·% of BP degraded by more than 20% within 4 weeks in the acidic degradation test and more than 5% in the soil burial degradation test. It was noticed that there was a considerable difference in the degradation between the PCL matrix and the biocomposites of PCL and BP. These results suggest that biodegradable composites could be a promising alternative material to the existing synthetic polymer composites.

Extrusion of Cell Encapsulated in Boron Nitride Nanotubes Reinforced Gelatin-Alginate Bioink for 3D Bioprinting.

Three-dimensional (3D) bioprinting, an innovative technology, has gained the attention of researchers as a promising technique for the redevelopment of complex tissue or organ structures. Despite significant advancements, a major challenge in 3D bioprinting is the limited number of suitable bioinks that fulfil the physiochemical requirements to produce complicated structures. Therefore, there is a demand for the production of bioinks for 3D bioprinting techniques. In this short communication, THP-1 cells encapsulated in boron nitride nanotubes (BNNTs) reinforced gelatin and alginate bioink was prepared. The study investigated the impact on the cells during printing using a fluorescence cell image. The results showed that the pure polymer bioinks demonstrated poor printability properties with the incorporation of cells. However, BNNT-combined bioink showed a significant increase in structural integrity even after the incorporation of cells. Furthermore, the scaffold structure was successfully printed with the cells incorporated bioink, and a considerable number of live cells were observed. With further studies, BNNTs as a promising nanomaterial for formulating bioink encapsulated with cells can be understood fully.

Boron nitride nanotubes reinforced gelatin hydrogel-based ink for bioprinting and tissue engineering applications.

The rapid evolution of 3D bioprinting technique, very few biomaterials have been studied and utilised as ink solutions to produce structures. In this work, a polymeric nanocomposite hydrogel-based ink solution was developed using boron nitride nanotubes (BNNTs) reinforced gelatin for 3D bioprinting of scaffolds. The ink solutions and printed scaffolds were characterised for their printability, mechanical, thermal, water uptake, and biological properties (cell viability and inflammation). The viscoelastic behaviour of the scaffolds indicated the increase in storage modulus with an increase in BNNTs composition. Additionally, the compressive strength of the scaffolds increased from 9.43 ± 1.3 kPa to 30.09 ± 1.5 kPa with the addition of BNNTs. Similarly, the thermal stability of the scaffolds enhanced with an increase in BNNTs composition. Furthermore, the scaffolds with a higher concentration of BNNTs displayed resilience in cell culture media at 37 °C for up to 14 days compared with pure gelatin scaffolds. The cell viability results showed a decreased viability rate with an increased concentration of BNNTs scaffolds. However, BNNTs incubated with cells did not display cytokine inflammation. Therefore, this work provides a potential hydrogel-based ink solution for 3D bioprinting of biomimetic tissue constructs with adequate structural stability for a wide range of tissue engineering and regenerative medicine applications.

Preparation and Characterisation of Wood Polymer Composites Using Sustainable Raw Materials.

In recent years, composites consisting of polymers and cellulosic materials have attracted increasing research attention. Polypropylene (PP) is among the most common polymer types found in excavated waste from landfills. Moreover, wood waste generated from wood products manufacturing such as sawdust (SD) offers a good potential for the fabrication of composite materials, and it is readily available in the environment. In this paper, wood polymer composites (WPC) consisting of recycled PP (rPP) and (SD) were prepared and characterised. A range of mechanical properties, including tensile strength, flexural properties, creep and hardness were studied, along with morphology, thermal properties, water degradation and contact angle. The results showed that the mechanical and thermal properties of rPP increased with an increase in 40 wt% of the SD content. Furthermore, the SD content significantly influenced the water uptake of the composites. Time-temperature superposition (TTS) was applied to predict the long-term mechanical performance from short-term accelerated creep tests at a range of elevated temperatures. The short-term creep test showed efficient homogeneity between the fillers and matrix with increasing temperature. The produced wood polymer composites displayed a comparable physical property to virgin polymer and wood and could potentially be used for various structural materials.

In Vitro and In Vivo Cytotoxicity of Boron Nitride Nanotubes: A Systematic Review.

Boron nitride nanotubes (BNNTs) are an exciting class of nanomaterials due to their unique chemical and physical characteristics. In recent decades, BNNTs have gained huge attention in research and development for various applications, including as nano-fillers for composites, semiconductor devices, hydrogen storage, and as an emerging material in biomedical and tissue engineering applications. However, the toxicity of BNNTs is not clear, and the biocompatibility is not proven yet. In this review, the role of BNNTs in biocompatibility studies is assessed in terms of their characteristics: cell viability, proliferation, therapeutic outcomes, and genotoxicity, which are vital elements for their prospective use in biomedical applications. A systematic review was conducted utilising the databases Scopus and Web of Science (WOS) (2008-2022). Additional findings were discovered manually by snowballing the reference lists of appropriate reviews. Only English-language articles were included. Finally, the significant analysis and discussion of the chosen articles are presented.

Extrusion-Based Bioprinted Boron Nitride Nanotubes Reinforced Alginate Scaffolds: Mechanical, Printability and Cell Viability Evaluation.

Alginate (Alg) hydrogels are commonly used as bioinks in 3D bioprinting. However, one of the significant drawbacks of using Alg hydrogels is their unstable mechanical properties. In this study, a novel hydrogel-based ink composed of Alg reinforced with functionalised boron nitride nanotubes (f-BNNTs) was developed and systematic quantitative characterisation was conducted to validate its printability, physiochemical properties and biocompatibility. The printability, contact angle and mechanical test results indicated good structural stability of the scaffolds. The thermal stability of the scaffolds increased with the incorporation of f-BNNTs into Alg. Human embryonic kidney cells (HEK 293T) were seeded on the scaffolds and the cell viability was recorded for 24, 48 and 72 h. Quantitative studies showed a slight effect on toxicity with a higher concentration of BNNTs in scaffolds. The results suggest that the 3D printable f-BNNTs reinforced Alg could be used as bioink for tissue engineering applications with further studies on biocompatibility.