Microplastic pollution on historic facades: Hidden 'sink' or urban threat?

Despite the increasing concerns surrounding the health and environmental risks of microplastics (MPs), the research focus has primarily been on their prevalence in air and the oceans, consequently neglecting their presence on urban facades, which are integral to our everyday environments. Therefore, there is a crucial knowledge gap in comprehending urban MP pollution. Our pioneering interdisciplinary study not only quantifies but also identifies MPs on historic facades, revealing their pervasive presence in a medium-sized urban area in the UK. In this case study, we estimated a mean density of 975,000 fibres/m^2 (0.10 fibres/mm^2) for fibre lengths between 30 and 1000 µm with a ratio of 1:5 for natural to artificial fibres. Our research identifies three groups of fibre length frequencies across varied exposure scenarios on the investigated urban facade. Sheltered areas (4m height) show a high prevalence of 60-120 µm and 180-240 µm fibres. In contrast, less sheltered areas at 3m exhibit lower fibre frequencies but similar lengths. Notably, the lowest area (2-1.5m) features longer fibres (300-1000 µm), while adjacent area S, near a faulty gutter, shows no fibres, highlighting the impact of exposure, altitude, and environmental variables on fibre distribution on urban facades. Our findings pave one of many necessary paths forward to determine the long-term fate of these fibres and provoke a pertinent question: do historic facades serve as an urban 'sink' that mitigates potentially adverse health impacts or amplifies the effects of mobile microplastics? Addressing MP pollution in urban areas is crucial for public health and sustainable cities. More research is required to understand the multi-scale factors behind MP pollution in large cities and to find mitigation strategies, paving the way for effective interventions and policies against this growing threat.

Effect of sample thinning on strains and lattice rotations measured from Transmission Kikuchi diffraction in the SEM.

Cross correlation based high angular resolution EBSD (or HR-EBSD) has been developed for measurement of elastic strains, lattice rotations (and estimating GND density). Recent advances in Transmission Kikuchi diffraction (TKD), especially the on-axis geometry allows the possibility of acquiring patterns at higher spatial resolution. However, some controversy remains as to whether stresses/strains measured after the sample thinning process are still representative of the bulk sample. In this paper, we explore a way of applying the HR-EBSD method to study strains and lattice rotations in an initially bulk sample, that is then progressively thinned down until a similar analysis can be performed on thin (and electron transparent) samples. Thus, HR-TKD will be compared as a possible alternative to HR-EBSD, in scenarios when it is not always possible to perform EBSD on the surface of the sample. An estimate of strain relaxation in the sample as a result of sample thinning is presented.

Predicting dwell fatigue life in titanium alloys using modelling and experiment.

Fatigue is a difficult multi-scale modelling problem nucleating from localised plasticity at the scale of dislocations and microstructure with significant engineering safety implications. Cold dwell fatigue is a phenomenon in titanium where stress holds at moderate temperatures lead to substantial reductions in cyclic life, and has been implicated in service failures. Using discrete dislocation plasticity modelling complemented by transmission electron microscopy, we successfully predict lifetimes for 'worst case' microstructures representative of jet engine spin tests. Fatigue loading above a threshold stress is found to produce slip in soft grains, leading to strong dislocation pile-ups at boundaries with hard grains. Pile-up stresses generated are high enough to nucleate hard grain basal dislocations, as observed experimentally. Reduction of applied cyclic load alongside a temperature excursion during the cycle lead to much lower densities of prism dislocations in soft grains and, sometimes, the elimination of basal dislocations in hard grains altogether.

Using local GND density to study SCC initiation.

Strain and geometric necessary dislocations (GNDs) have been mapped with nm-resolution around grain boundaries affected by stress corrosion cracking (SCC) or intergranular oxidation with the aim of clarifying which local conditions that trigger SCC initiation of Alloy 600 in primary water reactor (PWR) water environment. Regions studied included the cracked and uncracked portion of the same SCC-affected grain boundaries and a comparable grain boundary in the as-received condition. High-resolution "on-axis" Transmission Kikuchi Diffraction (TKD) was used to generate strain and GND density based on the cross-correlation image processing method to probe shifts of specific zone axis in the TKD patterns from all regions. All cracked boundaries analyzed had local GND densities higher than 1 × 1016 m-2. Similar grain boundaries, from as-received samples had GNDs of 5 × 1014 m-2, while an intermediate level was found in the oxidized but uncracked portion of the same GB. Results, together with a discussion on the advantages and limitations of the approach, will be presented.

Elastic strain tensor measurement using electron backscatter diffraction in the SEM.

The established electron backscatter diffraction (EBSD) technique for obtaining crystallographic information in the SEM has been adapted to permit elastic strain measurement. Basically, the displacement of crystallographic features in an EBSD pattern, such as zone axes, which result from strain in a crystal, is determined by comparing those same features as they appear in a pattern from an unstrained region of the crystal. The comparison is made by cross-correlation of selected regions in the two patterns. Tests show that the sensitivity to displacement measurement is 1 part in 10 000, which translates to a strain sensitivity of 2 parts in 10 000. Eight components of the strain tensor are determined directly and the ninth is calculated using the fact that the free surface of the sample is traction-free. Examples discussed are taken from studies of a lenticular fracture in germanium, the strain distribution surrounding a carbide precipitate in a nickel base alloy and grain boundary studies in another nickel base alloy.