How Transparent Oxides Gain Some Color: Discovery of a CeNiO3 Reduced Bandgap Phase As an Absorber for Photovoltaics.

In this work, we describe the formation of a reduced bandgap CeNiO3 phase, which, to our knowledge, has not been previously reported, and we show how it is utilized as an absorber layer in a photovoltaic cell. The CeNiO3 phase is prepared by a combinatorial materials science approach, where a library containing a continuous compositional spread of Ce xNi1- xO y is formed by pulsed laser deposition (PLD); a method that has not been used in the past to form Ce-Ni-O materials. The library displays a reduced bandgap throughout, calculated to be 1.48-1.77 eV, compared to the starting materials, CeO2 and NiO, which each have a bandgap of ∼3.3 eV. The materials library is further analyzed by X-ray diffraction to determine a new crystalline phase. By searching and comparing to the Materials Project database, the reduced bandgap CeNiO3 phase is realized. The CeNiO3 reduced bandgap phase is implemented as the absorber layer in a solar cell and photovoltages up to 550 mV are achieved. The solar cells are also measured by surface photovoltage spectroscopy, which shows that the source of the photovoltaic activity is the reduced bandgap CeNiO3 phase, making it a viable material for solar energy.

Process-Function Data Mining for the Discovery of Solid-State Iron-Oxide PV.

Data mining tools have been known to be useful for analyzing large material data sets generated by high-throughput methods. Typically, the descriptors used for the analysis are structural descriptors, which can be difficult to obtain and to tune according to the results of the analysis. In this Research Article, we show the use of deposition process parameters as descriptors for analysis of a photovoltaics data set. To create a data set, solar cell libraries were fabricated using iron oxide as the absorber layer deposited using different deposition parameters, and the photovoltaic performance was measured. The data was then used to build models using genetic programing and stepwise regression. These models showed which deposition parameters should be used to get photovoltaic cells with higher performance. The iron oxide library fabricated based on the model predictions showed a higher performance than any of the previous libraries, which demonstrates that deposition process parameters can be used to model photovoltaic performance and lead to higher performing cells. This is a promising technique toward using data mining tools for discovery and fabrication of high performance photovoltaic materials.

Vapor and healing treatment for CH3NH3PbI(3-x)Cl(x) films toward large-area perovskite solar cells.

Hybrid methyl-ammonium lead trihalide perovskites are promising low-cost materials for use in solar cells and other optoelectronic applications. With a certified photovoltaic conversion efficiency record of 20.1%, scale-up for commercial purposes is already underway. However, preparation of large-area perovskite films remains a challenge, and films of perovskites on large electrodes suffer from non-uniform performance. Thus, production and characterization of the lateral uniformity of large-area films is a crucial step towards scale-up of devices. In this paper, we present a reproducible method for improving the lateral uniformity and performance of large-area perovskite solar cells (32 cm(2)). The method is based on methyl-ammonium iodide (MAI) vapor treatment as a new step in the sequential deposition of perovskite films. Following the MAI vapor treatment, we used high throughput techniques to map the photovoltaic performance throughout the large-area device. The lateral uniformity and performance of all photovoltaic parameters (V(oc), J(sc), Fill Factor, Photo-conversion efficiency) increased, with an overall improved photo-conversion efficiency of ∼100% following a vapor treatment at 140 °C. Based on XRD and photoluminescence measurements, We propose that the MAI treatment promotes a "healing effect" to the perovskite film which increases the lateral uniformity across the large-area solar cell. Thus, the straightforward MAI vapor treatment is highly beneficial for large scale commercialization of perovskite solar cells, regardless of the specific deposition method.

A combined computational and experimental investigation of Mg doped α-Fe2O3.

In the current work, pristine α-Fe2O3 metal oxide was doped with Mg in an attempt to modulate its electronic properties. To this end, we employed an experimental high throughput strategy, including scanning XRD and optical spectroscopy, which were complimented by atomistic density functional theory (DFT) calculations. The combined study reveals that at Mg/Fe atomic ratios up to ∼1/3, the bandgaps of the hematite-Mg composite materials are similar to that of the pure material. The observed bandgaps are rationalized by electronic band structure and density of states calculations. Additional rationale for the similar bandgaps in pure and doped hematite is provided by topological Bader charge analyses, which indicate that the Mg and Fe ions in the hematite matrix have similar partial atomic charges. Nonetheless, the small charge density difference between the Mg and Fe ions induces a slight spin polarization on both oxygen and Fe ions, resulting in changes in the band edges. Further charge density analyses, using charge density maps and chemical-bonding analyses with the crystal orbital Hamiltonian population scheme, indicate that Mg forms ionic bonds with the neighboring oxygen atoms. This change from iron-oxygen covalent bonds to a more ionic nature for magnesium-oxygen bonds is probably responsible for the reduction observed in the computed bulk modulus of α-Mg(0.17)Fe(1.83)O3 (193 GPa) compared to α-Fe2O3 (202 GPa).

Open circuit potential build-up in perovskite solar cells from dark conditions to 1 sun.

The high open-circuit potential (Voc) achieved by perovskite solar cells (PSCs) is one of the keys to their success. The Voc analysis is essential to understand their working mechanisms. A large number of CH3NH3PbI3-xClx PSCs were fabricated on single large-area substrates and their Voc dependencies on illumination intensity, I0, were measured showing three distinctive regions. Similar results obtained in Al2O3 based PSCs relate the effect to the compact TiO2 rather than the mesoporous oxide. We propose that two working mechanisms control the Voc in PSCs. The rise of Voc at low I0 is determined by the employed semiconductor n-type contact (TiO2 or MgO coated TiO2). In contrast, at I0 close to AM1.5G, the employed oxide does not affect the achieved voltage. Thus, a change of regime from an oxide-dominated EFn (as in the dye sensitized solar cells) to an EFn, directly determined by the CH3NH3PbI3-xClx absorber is suggested.

Utilizing pulsed laser deposition lateral inhomogeneity as a tool in combinatorial material science.

Pulsed laser deposition (PLD) is widely used in combinatorial material science, as it enables rapid fabrication of different composite materials. Nevertheless, this method was usually limited to small substrates, since PLD deposition on large substrate areas results in severe lateral inhomogeneity. A few technical solutions for this problem have been suggested, including the use of different designs of masks, which were meant to prevent inhomogeneity in the thickness, density, and oxidation state of a layer, while only the composition is allowed to be changed. In this study, a possible way to take advantage of the large scale deposition inhomogeneity is demonstrated, choosing an iron oxide PLD-deposited library with continuous compositional spread (CCS) as a model system. An Fe2O3-Nb2O5 library was fabricated using PLD, without any mask between the targets and the substrate. The library was measured using high-throughput scanners for electrical, structural, and optical properties. A decrease in electrical resistivity that is several orders of magnitude lower than pure α-Fe2O3 was achieved at ∼20% Nb-O (measured at 47 and 267 °C) but only at points that are distanced from the center of the PLD plasma plume. Using hierarchical clustering analysis, we show that the PLD inhomogeneity can be used as an additional degree of freedom, helping, in this case, to achieve iron oxide with much lower resistivity.

Four-point probe electrical resistivity scanning system for large area conductivity and activation energy mapping.

The electrical properties of metal oxides play a crucial role in the development of new photovoltaic (PV) systems. Here we demonstrate a general approach for the determination and analysis of these properties in thin films of new metal oxide based PV materials. A high throughput electrical scanning system, which facilitates temperature dependent measurements at different atmospheres for highly resistive samples, was designed and constructed. The instrument is capable of determining conductivity and activation energy values for relatively large sample areas, of about 72 × 72 mm(2), with the implementation of geometrical correction factors. The efficiency of our scanning system was tested using two different samples of CuO and commercially available Fluorine doped tin oxide coated glass substrates. Our high throughput tool was able to identify the electrical properties of both resistive metal oxide thin film samples with high precision and accuracy. The scanning system enabled us to gain insight into transport mechanisms with novel compositions and to use those insights to make smart choices when choosing materials for our multilayer thin film all oxide photovoltaic cells.