Bioinspired Nanotopography for Combinatory Osseointegration and Antibacterial Therapy.

The ongoing global health has highlighted the critical issue of secondary infections, particularly antibiotic-resistant bacterial infections, which have been significant contributors to mortality rates. Orthopedic implants, while essential for trauma and orthopedic surgeries, are particularly susceptible to these infections, leading to severe complications and economic burdens. The traditional use of antibiotics in treating these infections poses further challenges including the risk of developing antibiotic-resistant bacteria. This study introduces a novel approach to combat this issue by developing nanostructured surfaces for orthopedic implants using target ion-induced plasma sputtering. Inspired by the natural design of dragonfly wings, these surfaces aim to prevent bacterial adhesion while promoting preosteoblast activity, offering a dual-function solution to the problems of bacterial infection and implant integration without relying on antibiotics. The in vitro results demonstrate the effectiveness of these bioinspired surfaces in eradicating bacteria and supporting cell proliferation and differentiation, presenting a promising alternative for the development of biomedical implants.

A strategy for enhancing bioactivity and osseointegration with antibacterial effect by incorporating magnesium in polylactic acid based biodegradable orthopedic implant.

Biodegradable orthopedic implants are essential for restoring the physiological structure and function of bone tissue while ensuring complete degradation after recovery. Polylactic acid (PLA), a biodegradable polymer, is considered a promising material due to its considerable mechanical properties and biocompatibility. However, further improvements are necessary to enhance the mechanical strength and bioactivity of PLA for reliable load-bearing orthopedic applications. In this study, a multifunctional PLA-based composite was fabricated by incorporating tricalcium phosphate (TCP) microspheres and magnesium (Mg) particles homogenously at a volume fraction of 40 %. This approach aims to enhance mechanical strength, accelerate pore generation, and improve biological and antibacterial performance. Mg content was incorporated into the composite at varying values of 1, 3, and 5 vol% (referred to as PLA/TCP-1 Mg, PLA/TCP-3 Mg, and PLA/TCP-5 Mg, respectively). The compressive strength and stiffness were significantly enhanced in all composites, reaching 87.7, 85.9, and 84.1 MPa, and 2.7, 3.0, and 3.1 GPa, respectively. The degradation test indicated faster elimination of the reinforcers as the Mg content increased, resulting in accelerated pore generation to induce enhanced osseointegration. Because PLA/TCP-3 Mg and PLA/TCP-5 Mg exhibited cracks in the PLA matrix due to rapid corrosion of Mg forming corrosion byproducts, to optimize the Mg particle content, PLA/TCP-1 Mg was selected for further evaluation. As determined by in vitro biological and antibacterial testing, PLA/TCP-1 Mg showed enhanced bioactivity with pre-osteoblast cells and exhibited antibacterial properties by suppressing bacterial colonization. Overall, the multifunctional PLA/TCP-Mg composite showed improved mechanobiological performance, making it a promising material for biodegradable orthopedic implants.

Antibacterial PLA/Mg composite with enhanced mechanical and biological performance for biodegradable orthopedic implants.

Biodegradability, bone-healing rate, and prevention of bacterial infection are critical factors for orthopedic implants. Polylactic acid (PLA) is a good candidate biodegradable material; however, it has insufficient mechanical strength and bioactivity for orthopedic implants. Magnesium (Mg), has good bioactivity, biodegradability, and sufficient mechanical properties, similar to that of bone. Moreover, Mg has an inherent antibacterial property via a photothermal effect, which generates localized heat, thus preventing bacterial infection. Therefore, Mg is a good candidate material for PLA composites, to improve their mechanical and biological performance and add an antibacterial property. Herein, we fabricated an antibacterial PLA/Mg composite for enhanced mechanical and biological performance with an antibacterial property for application as biodegradable orthopedic implants. The composite was fabricated with 15 and 30 vol% of Mg homogeneously dispersed in PLA without the generation of a defect using a high-shear mixer. The composites exhibited an enhanced compressive strength of 107.3 and 93.2 MPa, and stiffness of 2.3 and 2.5 GPa, respectively, compared with those of pure PLA which were 68.8 MPa and 1.6 GPa, respectively. Moreover, the PLA/Mg composite at 15 vol% Mg exhibited significant improvement of biological performance in terms of enhanced initial cell attachment and cell proliferation, whereas the composite at 30 vol% Mg showed deteriorated cell proliferation and differentiation because of the rapid degradation of the Mg particles. In turn, the PLA/Mg composites exerted an antibacterial effect based on the inherent antibacterial property of Mg as well as the photothermal effect induced by near-infrared (NIR) treatment, which can minimize infection after implantation surgery. Therefore, antibacterial PLA/Mg composites with enhanced mechanical and biological performance may be a candidate material with great potential for biodegradable orthopedic implants.

3D-Printed Functional Hydrogel by DNA-Induced Biomineralization for Accelerated Diabetic Wound Healing.

Chronic wounds in diabetic patients are challenging because their prolonged inflammation makes healing difficult, thus burdening patients, society, and health care systems. Customized dressing materials are needed to effectively treat such wounds that vary in shape and depth. The continuous development of 3D-printing technology along with artificial intelligence has increased the precision, versatility, and compatibility of various materials, thus providing the considerable potential to meet the abovementioned needs. Herein, functional 3D-printing inks comprising DNA from salmon sperm and DNA-induced biosilica inspired by marine sponges, are developed for the machine learning-based 3D-printing of wound dressings. The DNA and biomineralized silica are incorporated into hydrogel inks in a fast, facile manner. The 3D-printed wound dressing thus generates provided appropriate porosity, characterized by effective exudate and blood absorption at wound sites, and mechanical tunability indicated by good shape fidelity and printability during optimized 3D printing. Moreover, the DNA and biomineralized silica act as nanotherapeutics, enhancing the biological activity of the dressings in terms of reactive oxygen species scavenging, angiogenesis, and anti-inflammation activity, thereby accelerating acute and diabetic wound healing. These bioinspired 3D-printed hydrogels produce using a DNA-induced biomineralization strategy are an excellent functional platform for clinical applications in acute and chronic wound repair.

Manufacturing and Characterization of Dental Crowns Made of 5-mol% Yttria Stabilized Zirconia by Digital Light Processing.

We herein report manufacturing of dental crowns made of 5-mol% yttria partially stabilized zirconia (5Y-PSZ) with desired mechanical properties, optical translucency and dimensional accuracy using digital light processing (DLP). To this end, all processing parameters were carefully controlled and optimized. First, 5Y-PSZ particles with a bimodal distribution were prepared via calcination of as-received granules and subsequent ball-milling and then used to formulate 5Y-PSZ suspensions with a high solid loading of 50 vol% required for high densification after sintering. Dispersant content was also optimized. To provide high dimensional accuracy, initial dimensions of dental crowns for 3D printing were precisely determined by considering increase and decrease in dimensions during photopolymerization and sintering, respectively. Photopolymerization time was also optimized for a given layer thickness of 50 µm to ensure good bonding between layers. A multi-step debinding schedule with a slow heating rate was employed to avoid formation of any defects. After sintering at 1500 °C for 2 h, 5Y-PSZ could be almost fully densified without noticeable defects within layers and at interfaces between layers. They had high relative densities (99.03 ± 0.39%) with a high cubic phase content (59.1%). These characteristics allowed for achievement of reasonably high mechanical properties (flexural strength = 625.4 ± 75.5 MPa and Weibull modulus = 7.9) and % transmittance (31.4 ± 0.7%). In addition, 5Y-PSZ dental crowns showed excellent dimensional accuracy (root mean square (RMS) for marginal discrepancy = 44.4 ± 10.8 µm and RMS for internal gap = 22.8 ± 1.6 µm) evaluated by the 3D scanning technique.

Digital Light Processing of Zirconia Suspensions Containing Photocurable Monomer/Camphor Vehicle for Dental Applications.

This study reports the utility of solid camphor as a novel diluent in photocurable hexanediol diacrylate (HDDA) monomer to manufacture 4 mol% yttria partially stabilized zirconia (4Y-PSZ) components for dental applications by digital light processing (DLP). The use of a 65 wt% HDDA-35 wt% camphor solution allowed 4Y-PSZ suspensions to have reasonably low viscosities (1399 ± 55.8 mPa·s at a shear rate of 75 s-1), measured by a cone/plate viscometer, at a high solid loading of 48 vol%, where 4Y-PSZ particles prepared by calcination of as-received 4Y-PSZ granules, followed by a ball-milling process, were used with assistance of a dispersant. These 4Y-PSZ suspensions could be successfully applied to our custom-made DLP machine for manufacturing 4Y-PSZ components. To this end, several processing parameters, including layer thickness of 4Y-PSZ suspension, UV illumination time for layer-by-layer photocuring process, and initial dimensions of 4Y-PSZ objects, were tightly controlled. As sintering temperature increased from 1300 °C to 1500 °C, relative density and grain size of 4Y-PSZ objects increased, and cubic phase content also increased. Thus, after sintering at the highest temperature of 1500 °C for 3 h, high mechanical properties (biaxial flexural strength = 911 ± 40.7 MPa, hardness = 1371 ± 14.4 Hv) and reasonably high optical transmittance (translucency parameter = 7.77 ± 0.32, contrast ratio = 0.809 ± 0.007), evaluated by a spectrophotometer, were obtained due to a high relative density (97.2 ± 1.38%), which would be useful for dental applications.

Dual-Scale Porosity Alumina Structures Using Ceramic/Camphene Suspensions Containing Polymer Microspheres.

This study demonstrates the utility of thermo-regulated phase separable alumina/camphene suspensions containing poly(methyl methacrylate) (PMMA) microspheres as porogens for the production of multi-scale porosity structures. The homogeneous suspension prepared at 60 °C could undergo phase separation during freezing at room temperature. This process resulted in the 3D networks of camphene crystals and alumina walls containing PMMA microspheres. As a consequence, relatively large dendritic pores with several tens of microns size could be created as the replica of frozen camphene crystals. In addition, after the removal of PMMA microspheres via heat-treatment, micron-sized small spherical pores could be generated in alumina walls. As the PMMA content with respect to the alumina content increased from 0 vol% to 40 vol%, while the camphene content in the suspensions was kept constant (70 vol%), the overall porosity increased from 45.7 ± 0.5 vol% to 71.4 ± 0.5 vol%. This increase in porosity is attributed to an increase in the fraction of spherical pores in the alumina walls. Thus, compressive strength decreased from 153 ± 18.3 MPa to 33 ± 7.2 MPa. In addition, multi-scale porosity alumina objects with a honeycomb structure comprising periodic hexagonal macrochannels surrounded by dual-scale porosity walls were constructed using a 3D plotting technique.

Accelerated biodegradation of iron-based implants via tantalum-implanted surface nanostructures.

In recent years, pure iron (Fe) has attracted significant attention as a promising biodegradable orthopedic implant material due to its excellent mechanical and biological properties. However, in physiological conditions, Fe has an extremely slow degradation rate with localized and irregular degradation, which is problematic for practical applications. In this study, we developed a novel combination of a nanostructured surface topography and galvanic reaction to achieve uniform and accelerated degradation of an Fe implant. The target-ion induced plasma sputtering (TIPS) technique was applied on the Fe implant to introduce biologically compatible and electrochemically noble tantalum (Ta) onto its surface and develop surface nano-galvanic couples. Electrochemical tests revealed that the uniformly distributed nano-galvanic corrosion cells of the TIPS-treated sample (nano Ta-Fe) led to relatively uniform and accelerated surface degradation compared to that of bare Fe. Furthermore, the mechanical properties of nano Ta-Fe remained almost constant during a long-term in vitro immersion test (~40 weeks). Biocompatibility was also assessed on surfaces of bare Fe and nano Ta-Fe using in vitro osteoblast responses through direct and indirect contact assays and an in vivo rabbit femur medullary cavity implantation model. The results revealed that nano Ta-Fe not only enhanced cell adhesion and spreading on its surface, but also exhibited no signs of cellular or tissue toxicity. These results demonstrate the immense potential of Ta-implanted surface nanostructures as an effective solution for the practical application of Fe-based orthopedic implants, ensuring long-term biosafety and clinical efficacy.

Improved Biocompatibility of Intra-Arterial Poly-L-Lactic Acid Stent by Tantalum Ion Implantation : 3-Month Results in a Swine Model.

OBJECTIVE: Biodegradable poly-L-lactic acid (PLLA) with a highly biocompatible surface via tantalum (Ta) ion implantation can be an innovative solution for the problems associated with current biodegradable stents. The purpose of this study is to develop a Ta-implanted PLLA stent for clinical use and to investigate its biological performance capabilities. METHODS: A series of in vitro and in vivo tests were used to assess the biological performance of bare and Ta-implanted PLLA stents. The re-endothelialization ability and thrombogenicity were examined through in vitro endothelial cell and platelet adhesion tests. An in vivo swine model was used to evaluate the effects of Ta ion implantation on subacute restenosis and thrombosis. Angiographic and histologic evaluations were conducted at one, two and three months post-treatment. RESULTS: The Ta-implanted PLLA stent was successfully fabricated, exhibiting a smooth surface morphology and modified layer integration. After Ta ion implantation, the surface properties were more favorable for rapid endothelialization and for less platelet attachment compared to the bare PLLA stent. In an in vivo animal test, follow-up angiography showed no evidence of in-stent stenosis in either group. In a microscopic histologic examination, luminal thrombus formation was significantly suppressed in the Ta-implanted PLLA stent group according to the 2-month follow-up assessment (21.2% vs. 63.9%, p=0.005). Cells positive for CD 68, a marker for the monocyte lineage, were less frequently identified around the Ta-implanted PLLA stent in the 1-month follow-up assessments. CONCLUSION: The use of a Ta-implanted PLLA stent appears to promote re-endothelialization and anti-thrombogenicity.

Bifunctional poly (l-lactic acid)/hydrophobic silica nanocomposite layer coated on magnesium stents for enhancing corrosion resistance and endothelial cell responses.

Biodegradable magnesium (Mg)-based vascular stents can overcome the limitations of conventional permanent metallic stents, such as late in-stent restenosis and thrombosis, but still have difficulty retarding degradation while providing adequate mechanical support to the blood vessel. We incorporated silica nanoparticles surface-functionalized with hexadecyltrimethoxysilane (mSiNP) into a poly (l-lactic acid) (PLLA) coating as a physical barrier to disturb the penetration of the corrosive medium as well as a bioactive source that releases silicon ions capable of stimulating endothelial cells. The corrosion resistance and biocompatibility of this bifunctional PLLA/mSiNP nanocomposite coating were investigated using different weight ratios of mSiNP. The nanocomposite coating containing more than 10 wt% of the mSiNP (PLLA/10mSiNP and PLLA/20mSiNP) significantly delayed the corrosion of the Mg substrate and exhibited favorable endothelial cell responses, compared to the pure PLLA coating. Specifically, the calculated corrosion rates of PLLA/10mSiNP and PLLA/20mSiNP decreased by half, indicating the durability of the coating after immersion in simulated body fluid for 12 days. Based on the in vitro cellular response, the incorporation of the mSiNPs into the PLLA coating significantly improved the endothelial cell responses to the Mg substrate, showing better initial cell surface coverage, migration, and proliferation rate than those of pure PLLA. These results indicate that the PLLA/mSiNP nanocomposite coatings have significant potential to improve the corrosion resistance and vascular compatibility of biodegradable Mg-based vascular stents.

Nano-Topographical Control of Ti-Nb-Zr Alloy Surfaces for Enhanced Osteoblastic Response.

Nano-scale surface roughening of metallic bio-implants plays an important role in the clinical success of hard tissue reconstruction and replacement. In this study, the nano-topographical features of titanium-niobium-zirconium (TNZ) alloy surfaces were controlled by using the target-ion induced plasma sputtering (TIPS) technique to improve the in vitro osteoblastic response. The TIPS technique is a novel strategy for etching the surface of metallic bio-implants using bombardment of target metal cations, which were accelerated by an extremely high negative bias voltage applied to the substrates. The nano-topography of the TNZ surfaces was successfully controlled by modulating experimental variables (such as the ion etching energy and the type of substrate or target materials) of TIPS. As a result, various nanopatterns (size: 10-210 nm) were fabricated on the surface of the TNZ alloys. Compared with the control group, experimental groups with nanopattern widths of ≥130 nm (130 and 210 nm groups) exhibited superior cell adhesion, proliferation, and differentiation. Our findings demonstrate that TIPS is a promising technology that can impart excellent biological functions to the surface of metallic bio-implants.

Stable sol-gel hydroxyapatite coating on zirconia dental implant for improved osseointegration.

Aside from being known for its excellent mechanical properties and aesthetic effect, zirconia has recently attracted attention as a new dental implant material. Many studies have focused on hydroxyapatite (HA) coating for obtaining improved biocompatibility, however the coating stability was reduced by a byproduct produced during the high-temperature sintering process. In this study, to overcome this problem, we simply coated the zirconia surface with a sol-gel-derived hydroxyapatite (HA) layer and then sintered it at a varied temperature (<1000 °C). The surface showed a nanoporous structure, and there was no crystalline phase other than HA and zirconia when the sintering temperature was 800 °C. The adhesion strength of the HA layer (>40 MPa) was also appropriate as a dental implant application. In addition, in vitro cell experiments using a preosteoblast cell line revealed that the HA-coated zirconia surface acts as a preferable surface for cell attachment and proliferation than bare zirconia surface. In vivo animal experiments also demonstrated that the osteoconductivity of zirconia were dramatically enhanced by HA coating, which was comparable to that of Ti implant. These results suggest that the sol-gel-based HA-coated zirconia has a great potential for use as a dental implant material.

Construction of tantalum/poly(ether imide) coatings on magnesium implants with both corrosion protection and osseointegration properties.

Poly(ether imide) (PEI) has shown satisfactory corrosion protection capability with good adhesion strength as a coating for magnesium (Mg), a potential candidate of biodegradable orthopedic implant material. However, its innate hydrophobic property causes insufficient osteoblast affinity and a lack of osseointegration. Herein, we modify the physical and chemical properties of a PEI-coated Mg implant. A plasma immersion ion implantation technique is combined with direct current (DC) magnetron sputtering to introduce biologically compatible tantalum (Ta) onto the surface of the PEI coating. The PEI-coating layer is not damaged during this process owing to the extremely short processing time (30 s), retaining its high corrosion protection property and adhesion stability. The Ta-implanted layer (roughly 10-nm-thick) on the topmost PEI surface generates long-term surface hydrophilicity and favorable surface conditions for pre-osteoblasts to adhere, proliferate, and differentiate. Furthermore, in a rabbit femur study, the Ta/PEI-coated Mg implant demonstrates significantly enhanced bone tissue affinity and osseointegration capability. These results indicate that Ta/PEI-coated Mg is promising for achieving early mechanical fixation and long-term success in biodegradable orthopedic implant applications.

Polydeoxyribonucleotide-delivering therapeutic hydrogel for diabetic wound healing.

Patients with diabetes experience delayed wound healing because of the uncontrolled glucose level in their bloodstream, which leads to impaired function of white blood cells, poor circulation, decreased production and repair of new blood vessels. Treatment using polydeoxyribonucleotide (PDRN), which is a DNA extracted from the sperm cells of salmon, has been introduced to accelerate the healing process of diabetic wounds. To accelerate the wound-healing process, sustained delivery of PDRN is critical. In this study, taking advantage of the non-invasive gelation property of alginate, PDRN was loaded inside the hydrogel (Alg-PDRN). The release behavior of PDRN was altered by controlling the crosslinking density of the Alg hydrogel. The amount of PDRN was the greatest inside the hydrogel with the highest crosslinking density because of the decreased diffusion. However, there was an optimal degree of crosslinking for the effective release of PDRN. In vitro studies using human dermal fibroblasts and diabetes mellitus fibroblasts and an in ovo chorioallantoic membrane assay confirmed that the Alg-PDRN hydrogel effectively induced cell proliferation and expression of angiogenic growth factors and promoted new blood vessel formation. Its effectiveness for accelerated diabetic wound healing was also confirmed in an in-vivo animal experiment using a diabetic mouse model.

Enhanced Bioactivity of Micropatterned Hydroxyapatite Embedded Poly(L-lactic) Acid for a Load-Bearing Implant.

Poly(L-lactic) acid (PLLA) is among the most promising polymers for bone fixation, repair, and tissue engineering due to its biodegradability and relatively good mechanical strength. Despite these beneficial characteristics, its poor bioactivity often requires incorporation of bioactive ceramic materials. A bioresorbable composite made of PLLA and hydroxyapatite (HA) may improve biocompatibility but typically causes deterioration in mechanical properties, and bioactive coatings inevitably carry a risk of coating delamination. Therefore, in this study, we embedded micropatterned HA on the surface of PLLA to improve bioactivity while eliminating the risk of HA delamination. An HA pattern was successfully embedded in a PLLA matrix without degeneration of the matrix's mechanical properties, thanks to a transfer technique involving conversion of Mg to HA. Furthermore, patterned HA/PLLA's biological response outperformed that of pure PLLA. These results confirm patterned HA/PLLA as a candidate for wide acceptance in biodegradable load-bearing implant applications.

PLLA Membrane with Embedded Hydroxyapatite Patterns for Improved Bioactivity and Efficient Delivery of Growth Factor.

Poly(l-lactic) acid (PLLA) is widely used in guided bone regeneration membranes due to its mechanical properties and biodegradability. However, the lack of biocompatibility is a serious disadvantage. Herein, the biocompatibility of PLLA is improved by patterning hydroxyapatite (HA) loaded with recombinant human bone morphogenetic protein-2 (rhBMP-2) under it. The HA is obtained by preparing a magnesium pattern via photolithography and hydrothermal converting. After loading rhBMP-2, the pattern is transferred to PLLA. The pattern is tightly embedded in the PLLA and retained its original position after mechanical stimuli. Fluorescence images allow to assess the protein adsorption and gradual release in a controlled manner. The amount of released rhBMP-2 is overwhelmingly large when loaded under HA because of its large surface area. Osteogenic differentiation supports the synergistic effect of HA and rhBMP-2 to improve the biocompatibility. Moreover, in vivo experiments demonstrate that the synergistic effect positively affects the healing rate of bone.

Tantalum-coated polylactic acid fibrous membranes for guided bone regeneration.

Guided bone regeneration (GBR) membrane is necessary to reconstruct the defect bone tissue by defending penetration of soft tissues. Polylactic acid (PLA) attracts much attention to utilize as a GBR membrane because it has relatively high mechanical strength and biodegradability. However, the poor osteoconductivity of PLA is a major concern. The aim of this study is to improve the osteoconductivity of fibrous, electrospun, PLA guided bone regeneration membranes by coating the fiber surface with highly biocompatible tantalum (Ta). Ta coating of electrospun PLA membrane was created through sputtered Ta ions surrounding the PLA fibers. The Ta-coated PLA (Ta-PLA) membranes remain a randomly aligned fibrous structure with no defects caused by sputtering. The chemical composition of Ta-PLA membrane indicates Ta coating was well deposited on PLA fibers. Although the mechanical strength of Ta-PLA was reduced compared with bare PLA membrane, the Ta coating layer does not readily delaminate from the single PLA fiber surface due to its cladded structure which indicates that the Ta coating has high mechanical stability on PLA fibers. In vitro cell tests demonstrate that the attachment, proliferation, and differentiation of preosteoblasts are significantly promoted on the Ta-PLA membranes compared to bare PLA. In an in vivo animal test, most calvarial defects in the Ta-PLA group are covered with newly formed bone within six weeks, while the defects in the bare PLA group are rarely covered. Furthermore, the degree of bone healing in the Ta-PLA group is comparable to healing observed on collagen membranes, which are highly bioactive materials. These results indicate the superior osteoconductivity of Ta-PLA will make it particularly useful as a guided bone regeneration membrane.

Tantalum - Poly (L-lactic acid) nerve conduit for peripheral nerve regeneration.

Recently, Tantalum (Ta) has been re-explored and used with bone implants to promote bone regeneration. It has previously been extensively used as a nerve suture material; however, its use was abandoned because of the formation of scar tissue. In this study, we constructed a nerve conduit made of poly (L-lactic acid) PLA (outer layer) and tantalum Ta (inner layer) to evaluate its efficiency in the promotion of peripheral nerve regeneration. MATERIALS AND METHODS: First, we conducted an in vitro study to evaluate the viability and proliferation of Schwann cells and rat pheocromocytoma (PC-12) cells on Ta-PLA sheets using Enhanced Cell Viability Assay Kit (EZ-CYTOX). An in vivo study was then performed using Sprague Dawley rats that were randomly divided into the following three groups: sham, PLA, and Ta-PLA nerve conduits. The nerve conduit was placed over a 10-mm gap of the rat sciatic nerve to promote nerve regeneration. The rats were observed over 12 wk with weekly sciatic functional index functional assessment. At the end of 12 wk, the nerve regeneration outcome was assessed through dorsal root ganglions (DRG) retrograde neurons labeling, histomorphometric analysis, and histological analysis. RESULTS: The in vitro study showed significant viability and proliferation of Schwann cells in the Ta-PLA group than in the other groups. In the in vivo study, the gross findings revealed well-regenerated neural tissue in both the experimental groups with no scarring. The histological analysis showed that about 50 % of the conduits were filled with axons with a higher tendency for peripheral growth in the PLA group than for central growth within the Ta-PLA group conduits. The retrograde labeled neurons were significantly higher in Ta-PLA group than in the PLA group. Ta-PLA showed non-significant difference in the total fibers compared to the sham group. CONCLUSION: Tantalum proved favorable for the growth of Schwann cells.In vivo, Ta-PLA nerve conduit induced peripheral nerve regeneration without scar tissue formation.

Porous calcium phosphate-collagen composite microspheres for effective growth factor delivery and bone tissue regeneration.

Microspheres are beneficial for filling defects of various shapes and provide a large surface area for cell attachment. Porous microspheres have attracted particular attention because they can deliver cells and bioactive molecules such as growth factors. In this study, BCP-collagen composite microspheres were developed for growth factor delivery in bone regeneration. Firstly, porous biphasic calcium phosphate (BCP) microspheres were fabricated by applying a water-in-oil emulsion technique using camphene as a pore generator. Then, porous BCP-collagen composite microspheres were fabricated by repetitively dip coating the microspheres in a collagen solution to effectively deliver growth factor to bone defects. Characterization of the microspheres and in vitro studies were conducted to investigate the effect of collagen infiltration on bone regeneration. In addition, in vitro evaluation demonstrated the sustained bone morphogenetic protein-2 (BMP-2) delivery of the microspheres and the effect of cell differentiation, and in vivo assessment with rabbits revealed that the microspheres filled the defect well and that bone could be regenerated through the microspheres. Moreover, the composite system was more effective for bone regeneration than the bare BCP microspheres because of the drug retention of collagen. These findings indicate that the porous microspheres are effective for tissue regeneration by continuous growth factor delivery.

Biodegradable magnesium alloy (WE43) in bone-fixation plate and screw.

The purpose of the present study was to evaluate the mechanical strength and the absorption rate of WE43 material and to develop an absorbable metallic plate and screw for craniofacial application. The extruded WE43 plate and screw were evaluated using a LeFort I osteotomy canine model of 10 beagle dogs. Animals were divided into two groups: five dogs in the experimental group and five dogs in the control group. µCT was acquired at 4, 12, and 24 weeks. At 24 weeks after the operation, all animals were sacrificed, and histologic evaluation was performed. Swelling and gas formation were observed in three dogs in the experimental groups at 8 weeks. From 12 weeks, infraorbital fistula and inflammation were observed in three dogs in the experimental group, which gradually decreased and disappeared at 24 weeks. Other two dogs showed less gas formation at 12 weeks. The plates were completely absorbed, and gas formation was not observed at 24 weeks in these two dogs. New bone was well formed around the plates and screws in both groups. Histologic examination showed no specific differences between two groups. The mechanical strength of extruded WE43 was sufficient for mid-facial application. Plates and screws made with appropriately treated WE43 have the potential to be useful clinically.