Evaluation of PVC-Type Insulation Foam Material for Cryogenic Applications.

With the International Maritime Organization (IMO) reinforcing environmental regulations on the shipbuilding industry, the demand for fuels, such as liquefied natural gas (LNG) and liquefied petroleum gas (LPG), has soared. Therefore, the demand for a Liquefied Gas Carrier for such LNG and LPG also increases. Recently, CCS carrier volume has been increasing, and damage to the lower CCS panel has occurred. To withstand liquefied gas loads, the CCSs should be fabricated using a material with improved mechanical strength and thermal performance compared with the conventional material. This study proposes a polyvinyl chloride (PVC)-type foam as an alternative to commercial polyurethane foam (PUF). The former material functions as both insulation and a support structure primarily for the LNG-carrier CCS. To investigate the effectiveness of the PVC-type foam for a low-temperature liquefied gas storage system, various cryogenic tests, namely tensile, compressive, impact, and thermal conductivity, are conducted. The results illustrate that the PVC-type foam proves stronger than PUF in mechanical performance (compressive, impact) across all temperatures. In the tensile test, there are reductions in strength with PVC-type foam but it meets CCS requirements. Therefore, it can serve as insulation and improve the overall CCS mechanical strength against increased loads under cryogenic temperatures. Additionally, PVC-type foam can serve as an alternative to other materials in various cryogenic applications.

Proposing a new solution for marine debris by utilizing on-board low-temperature eco-friendly pulverization system.

Developing an effective and efficient recycling process for marine debris (MD) is one of the most urgent issues to maintain environmental sustainability on Earth. However, restricted storage capacities and secondary pollution (e.g., microbial adhesion, putrefaction) limit the proper MD recycling. Here, we proposed a complete eco-friendly low-temperature MD pulverizing system that utilizes excessive liquefied natural gas (LNG) cold energy (LCE) in an LNG propulsion ship to improve the efficiency and effectiveness of MD recycling. The prototype design of the low-temperature pulverization (LTP) system showed that consumable refrigerant (liquid nitrogen) up to 2831 kg per hour could be substituted. Furthermore, with a 20% ship output, 1250 kg of MD could be treated with 363 kg of additional refrigerant. In addition, LTP systems utilizing LCE could increase the storage capacity by more than 10 times compared to bulk MD while minimizing the required energy consumption. To determine the feasibility of LTP for MD recycling, four types of plastics obtained from actual MD from a coastal area in Busan, Korea were classified and tested.

Influence of Silica-Aerogel on Mechanical Characteristics of Polyurethane-Based Composites: Thermal Conductivity and Strength.

Polyurethane foam (PUF) has generally been used in liquefied natural gas (LNG) carrier cargo containment systems (CCSs) owing to its excellent mechanical and thermal properties over a wide range of temperatures. An LNG CCS must be designed to withstand extreme environmental conditions. However, as the insulation material for LNGC CCSs, PUF has two major limitations: its strength and thermal conductivity. In the present study, PUFs were synthesized with various weight percentages of porous silica aerogel to reinforce the characteristics of PUF used in LNG carrier insulation systems. To evaluate the mechanical strength of the PUF-silica aerogel composites considering LNG loading/unloading environmental conditions, compressive tests were conducted at room temperature (20 °C) and a cryogenic temperature (-163 °C). In addition, the thermal insulation performance and cellular structure were identified to analyze the effects of silica aerogels on cell morphology. The cell morphology of PUF-silica aerogel composites was relatively homogeneous, and the cell shape remained closed at 1 wt.% in comparison to the other concentrations. As a result, the mechanical and thermal properties were significantly improved by the addition of 1 wt.% silica aerogel to the PUF. The mechanical properties were reduced by increasing the silica aerogel content to 3 wt.% and 5 wt.%, mainly because of the pores generated on the surface of the composites.

Synthesis and Investigation of Cryogenic Mechanical Properties of Chopped-Glass-Fiber-Reinforced Polyisocyanurate Foam.

Polyisocyanurate foam (PIF) has been adopted as a liquefied natural gas (LNG) insulating material owing to its various mechanical merits such as high structural stability and mechanical strength, and excellent insulating ability. In an attempt to increase the mechanical strength of PIF, chopped-glass-fiber-reinforced polyisocyanurate foam (CGR-PIF) was synthesized by adding chopped glass fibers to polyol and isocyanate, which are the raw materials used in the polymerization process for producing PIF. The main objective is to closely observe the compression material characteristics of PIF and CGR-PIF in terms of the cryogenic temperature. Therefore, compressive tests were conducted at cryogenic temperature including low temperatures, and microscopic images were obtained to analyze the cell size and distribution that affects the mechanical and thermal properties of the foam. Furthermore, recovery ratio and weight loss which are important factors of brittle fracture were evaluated, and the applicability of the foams to a cryogenic environment was evaluated. Finally, thermal conductivity, an important parameter of insulation, was evaluated. The obtained results confirm that the compressive strength of CGR-PIF significantly increases at cryogenic temperatures; moreover, a relatively higher thermal conductivity was observed in the case of CGR-PIF as compared to that of PIF owing to the chopped glass fibers.

Low-temperature large-area fabrication of ZnO nanowires on flexible plastic substrates by solution-processible metal-seeded hydrothermal growth.

We have developed the low-temperature conformal ZnO nanowire fabrication on flexible plastic substrates by utilizing the solution-processible metal seed-assisted hydrothermal ZnO crystallization. Structural evolution of ZnO nanowires controlled by major parameters involving growth temperature, growth time, and seed coating condition, has been systematically investigated towards uniform and large-area growth of conformal ZnO nanowires. Direct ZnO nanowire growth on flexible plastics without undergoing the high-temperature seed sintering has been realized by developing the low-temperature Ag-seeded hydrothermal ZnO nanowire growth. The nanoporous Ag layer favorable for ZnO crystal nucleation and continued nanowire growth can be reduced from the Ag ion solution coating at the temperature as low as 130 °C. This tactfully enables the selective hydrothermal growth of ZnO nanowires on the Ag patterns on flexible plastics. Such an all-solution-processible low-temperature fabrication protocol may provide an essential and practical solution to develop many diverse applications including wearable and transparent electronics, sensors, and photocatalytic devices. As one example, we demonstrate that a transparent UV sensor can be devised based on the ZNW growth on the Ag micromesh electrode.

The Ratio of Dietary n-3 Polyunsaturated Fatty Acids Influences the Fat Composition and Lipogenic Enzyme Activity in Adipose Tissue of Growing Pigs.

Currently, there is a growing interest among consumers in selecting healthier meat with a greater proportion of essential fatty acids (FA). This experiment was conducted to evaluate the role of different ratios of dietary n-6:n-3 on growth performance, FA profile of longissimus dorsi (LD), relative gene expression of cytokines, meat quality, and blood parameters in finishing pigs. A total of 108 finishing pigs was randomly allotted to three treatments including a control (basal diet) and low ratios (4:1 and 2:1) of n-6:n-3. The 4:1 and 2:1 diets decreased the overall stearic acid in LD. There were reductions in the content of stearic acid, palmitoleic acid, total saturated acid, and n-6:n-3 ratio of LD in pigs fed 4:1 and 2:1 diet compared with the control diet. The 4:1 and 2:1 diets increased the concentration of α-Linolenic acid and polyunsaturated FA in the LD of pigs. Acetyl-CoA carboxylase enzyme gene was down-regulated in pigs fed 2:1 diet compared with finishing pigs fed the control or 4:1 diets. The relative expression of hormone-sensitive lipase was increased in pigs fed 2:1 and 4:1 ratio diets. Lower total cholesterol of plasma was observed in finishing pigs fed 2:1 and 4:1 diets. The cooking loss ratio of meat was lower in pigs fed the 2:1 and 4:1 diets compared with the control diet. Pigs fed the 4:1 and 2:1 diets had greater final body weight. In conclusion, the 2:1 and 4:1 diets have the potential to increase the meat quality and growth performance of pigs.

Genome-wide analysis of Hanwoo and Chikso populations using the BovineSNP50 genotyping array.

Hanwoo and Chikso are classified as Korean native cattle breeds that are currently registered with the Food and Agriculture Organization. However, there is still a lack of genomic studies to compare Hanwoo to Chikso populations. The objective of this study was to perform genome-wide analysis of Hanwoo and Chikso populations, investigating the genetic relationships between these two populations. We genotyped a total of 319 cattle including 214 Hanwoo and 105 Chikso sampled from Gangwon Province Livestock Technology Research Institute, using the Illumina Bovine SNP50K Beadchip. After performing quality control on the initially generated datasets, we assessed linkage disequilibrium patterns for all the possible SNP pairs within 1 Mb apart. Overall, average r2 values in Hanwoo (0.048) were lower than Chikso (0.074) population. The genetic relationship between the populations was further assured by the principal component analysis, exhibiting clear clusters in each of the Hanwoo and Chikso populations, respectively. Overall heterozygosity for Hanwoo (0.359) was slightly higher than Chikso (0.345) and inbreeding coefficient was also a bit higher in Hanwoo (- 0.015) than Chikso (- 0.035). The average FST value was 0.036 between Hanwoo and Chikso, indicating little genetic differentiation between those two breeds. Furthermore, we found potential selection signatures including LRP1B and NTRK2 genes that might be implicated with meat and reproductive traits in cattle. In this study, the results showed that both Hanwoo and Chikso populations were not under severe level of inbreeding. Although the principal component analysis exhibited clear clusters in each of the populations, we did not see any clear evidence that those two populations are highly differentiated each other.

Rapid and conformal coating of polymer resins by airbrushing for continuous and high-speed roll-to-roll nanopatterning: parametric quality controls and extended applications.

We present a facile and scalable coating method based on controlled airbrushing, which is suitable for conformal resin coating in continuous roll-to-roll (R2R) nanoimprint lithography (NIL) process. By controlling the concentration of UV-curable polymeric resin with mixing the volatile solvent and its airbrushing time, the coated resin film thickness can be readily tuned. After R2R NIL using a flexible nanoscale line pattern (nanograting) mold is conducted upon the airbrushed resin film, a large-area uniform nanograting pattern is fabricated with controlled residual layer thickness (RLT) based on the initial film thickness. We investigate the faithful airbrushing condition that can reliably create the uniform thin films as well as various nanopatterns with controlled morphologies. Using more diluted resin and shorter airbrushing time can reduce the RLTs favourably for many applications, yet is apt to induce the nanoscale pores and discontinued lines. We also discuss how to further improve the quality and scalability of resin airbrushing and its potential applications particularly requiring high-speed and conformal coating on highly topographic and flexible surfaces.

Copy number variations in Hanwoo and Yanbian cattle genomes using the massively parallel sequencing data.

Hanwoo is an indigenous Korean beef cattle breed, and it shared an ancestor with Yanbian cattle that are found in the Northeast provinces in China until the last century. During recent decades, those cattle breeds experienced different selection pressures. Here, we present genome-wide copy number variations (CNVs) by comparing Hanwoo and Yanbian cattle sequencing data. We used ~3.12 and ~3.07 billion sequence reads from Hanwoo and Yanbian cattle, respectively. A total of 901 putative CNV regions (CNVRs) were identified throughout the genome, representing 5,513,340bp. This is a smaller number than has been reported in previous studies, indicating that Hanwoo are genetically close to Yanbian cattle. Of the CNVRs, 53.2% and 46.8% were found to be gains and losses in Hanwoo. Potential functional roles of each CNVR were assessed by annotating all CNVRs and gene ontology (GO) enrichment analysis. We found that 278 CNVRs overlapped with cattle gene-sets (genic-CNVRs) that could be promising candidates to account for economically important traits in cattle. The enrichment analysis indicated that genes were significantly over-represented in GO terms, including developmental process, multicellular organismal process, reproduction, and response to stimulus. These results provide a valuable genomic resource for determining how CNVs are associated with cattle traits.

Nitrogen Removal from Milking Center Wastewater via Simultaneous Nitrification and Denitrification Using a Biofilm Filtration Reactor.

Milking center wastewater (MCW) has a relatively low ratio of carbon to nitrogen (C/N ratio), which should be separately managed from livestock manure due to the negative impacts of manure nutrients and harmful effects on down-stream in the livestock manure process with respect to the microbial growth. Simultaneous nitrification and denitrification (SND) is linked to inhibition of the second nitrification and reduces around 40% of the carbonaceous energy available for denitrification. Thus, this study was conducted to find the optimal operational conditions for the treatment of MCW using an attached-growth biofilm reactor; i.e., nitrogen loading rate (NLR) of 0.14, 0.28, 0.43, and 0.58 kg m(-3) d(-1) and aeration rate of 0.06, 0.12, and 0.24 m(3) h(-1) were evaluated and the comparison of air-diffuser position between one-third and bottom of the reactor was conducted. Four sand packed-bed reactors with the effective volume of 2.5 L were prepared and initially an air-diffuser was placed at one third from the bottom of the reactor. After the adaptation period of 2 weeks, SND was observed at all four reactors and the optimal NLR of 0.45 kg m(-3) d(-1) was found as a threshold value to obtain higher nitrogen removal efficiency. Dissolved oxygen (DO) as one of key operational conditions was measured during the experiment and the reactor with an aeration rate of 0.12 m(3) h(-1) showed the best performance of NH4-N removal and the higher total nitrogen removal efficiency through SND with appropriate DO level of ~0.5 mg DO L(-1). The air-diffuser position at one third from the bottom of the reactor resulted in better nitrogen removal than at the bottom position. Consequently, nitrogen in MCW with a low C/N ratio of 2.15 was successfully removed without the addition of external carbon sources.

Optimal Incorporation Level of Dietary Alternative Phosphate (MgHPO4) and Requirement for Phosphorus in Juvenile Far Eastern Catfish (Silurus asotus).

A growth trial was conducted to determine the optimal incorporation level of dietary magnesium hydrogen phosphate (MHP, MgHPO4), which was manufactured from swine manure and phosphorus (P), required by juvenile far eastern catfish (Silurus asotus). Graded MHP of 0.5%, 1.0%, 1.5%, and 2.0%, and 2.0% monocalcium phosphate (MCP) each was added to the basal diet (control) in lieu of cellulose to become the range of available P (AP) from 0.4% to 0.8% of which diets were designated as control, MHP0.5, MHP1.0, MHP1.5, MHP2.0, and MCP, respectively. Control diet contained fish meal (20%), soybean meal (40%), wheat flour (27%), corn gluten meal (5%), fish oil (2%) and soy oil (2%) as main ingredients. Following a 24 h fasting, 540 fish with a mean body weight of 11.8 g were randomly allotted to 6 groups in triplicate, whereby 18 tanks (0.4×0.6×0.36 cm, water volume of 66 L) were prepared. The feeding experiment lasted for 8 weeks. Fish group fed the control diet showed the lowest weight gain (WG) and feed efficiency (FE) among treatments. The WG was, however, not significantly different (p>0.05) from that of fish group fed MHP0.5. Fish group fed MHP2.0 showed the highest WG and FE of which values were not significantly different from those of fish groups fed diets MHP1.0 and MHP1.5 as well as MCP (p>0.05) except fish groups fed control and MHP0.5. Aspartate aminotransferase was significantly decreased with an increase in available P, while alanine aminotransferase did not show a significant difference among treatment. The highest inorganic P in plasma was observed in fish fed MHP2.0. From the present results, a second-order regression analysis revealed that the optimal dietary MHP level and the AP requirement were found to be 1.62% and 0.7%, respectively.

Effects of Dietary Garlic Powder on Growth, Feed Utilization and Whole Body Composition Changes in Fingerling Sterlet Sturgeon, Acipenser ruthenus.

A 12 week growth study was carried out to investigate the supplemental effects of dietary garlic powder (GP) on growth, feed utilization and whole body composition changes of fingerling sterlet sturgeon Acipenser ruthenus (averaging weight, 5.5 g). Following a 24-h fasting, 540 fish were randomly distributed to each of 18 tanks (30 fish/tank) under a semi-recirculation freshwater system. The GP of 0.5% (GP0.5), 1% (GP1), 1.5% (GP1.5), 2% (GP2) and 3% (GP3) was added to the control diet (GP0) containing 43% protein and 16% lipid. After the feeding trial, weight gain (WG) of fish fed GP1.5, GP2 and GP3 were significantly higher (p<0.05) than those of fish fed GP0, GP0.5 and GP1. Feed efficiency and specific growth rate (SGR) showed a similar trend to WG. Protein efficiency ratio of fish fed GP1.5, GP2, and GP3 were significantly higher (p<0.05) than those of fish groups fed the other diets. A significant difference (p<0.05) was found in whole body composition (moisture, crude protein, crude lipid, ash, and fiber) of fish at the end of the experiment. Significantly higher (p<0.05) protein and lipid retention efficiencies (PRE and LRE) were also found in GP1.5, GP2, and GP3 groups. Broken-line regression model analysis and second order polynomial regression model analysis relation on the basis of SGR and WG indicated that the dietary optimal GP level could be greater than 1.77% and 1.79%, but less than 2.95% and 3.18% in fingerling sterlet sturgeon. The present study suggested that dietary GP for fingerling sterlet sturgeon could positively affect growth performance and protein retention.

Effects of Dietary Supplementation of Magnesium Hydrogen Phosphate (MgHPO4) as an Alternative Phosphorus Source on Growth and Feed Utilization of Juvenile Far Eastern Catfish (Silurus asotus).

The present study was conducted to investigate a supplemental effect of magnesium hydrogen phosphate (MHP, MgHPO4) as an alternative phosphorus (P) source on growth and feed utilization of juvenile far eastern catfish (Silurus asotus) in comparison with three conventional P additives (monocalcium phosphate (MCP), dicalcium phosphate (DCP) and tricalcium phosphate [TCP]) as positive controls. A basal diet as a negative control was prepared without P supplementation and four supplemental P sources were added at the level of 2%. Five groups of 450 fish having mean body weight of 11.3 g following 24 h fasting after three week adaptation period were randomly distributed into each of 15 tanks (30 fish/tank). Fish were hand-fed to apparent satiety twice a day for 8 weeks. Fish fed MHP had weight gain (WG), protein efficiency ratio and specific growth rate comparable to those fed MCP. Fish fed MHP and MCP had feed efficiency (FE) significantly higher (p<0.05) than those fed DCP. Fish groups fed control and TCP showed the lower FE than the other groups which was significantly different (p<0.05) from those of fish fed the other diets. Survival rate was not significantly different (p>0.05) among treatments. Fish fed control had the lowest hematocrit, which was significantly different (p<0.05) from that of fish fed MHP. Fish fed MCP and MHP had plasma P higher (p<0.05) than fish fed the other diets. Relative efficiencies of MCP, DCP and TCP to MHP were found to be 100.5 and 101.3%, 92.0 and 91.6%, and 79.1 and 80.9% for WG and FE, respectively. P availability was determined to be 88.1%, 75.2%, 8.7%, and 90.9% for MCP, DCP, TCP, and MHP, respectively. Consequently, MHP recovered from wastewater stream showed that as an alternative P source its performance was comparative with MCP on growth and feed utilization of juvenile far eastern catfish.

Effects of Dietary Supplementation of Barodon, an Anionic Alkali Mineral Complex, on Growth Performance, Feed Utilization, Innate Immunity, Goblet Cell and Digestibility in Olive Flounder (Paralichthys olivaceus).

A 15-wk feeding trial was conducted to examine the supplemental effects of Barodon on growth performance, gastrointestinal histology, feed digestibility and innate immunity in olive founder. A basal commercial diet was used as a control and two other diets were prepared by spraying 0.1% or 0.2% of Barodon. Triplicate groups of fish (BW, 145 g) were fed one of the test diets to apparent satiation twice daily. At the end of the feeding trial, fish growth performance was not significantly affected by dietary treatments; however, feed utilization was significantly improved (linear and quadratic, p<0.05) by Barodon supplementation. Significantly higher (p<0.05) survival rates were obtained in fish fed Barodon containing diets. Hepatosomatic index increased significantly in Barodon treated groups. Also, the use of Barodon resulted in significant increase (linear and quadratic, p<0.05) of intestine length and number of goblet cells. Significantly higher (Quadratic, p<0.05) apparent digestibility coefficient of DM was obtained by supplementation of Barodon. Lysozyme and myeloperoxidase activities increased quadratically and linearly, respectively, in Barodon treated fish. Also, significantly higher (linear and quadratic, p<0.05) superoxide dismutase activity was found in Barodon fed fish. The findings in this study show that inclusion of Barodon in diets for olive flounder improves feed utilization and digestibility, and positively affects digestive tract histology and innate immunity.

Effects of Dietary Garlic Extracts on Whole Body Amino Acid and Fatty Acid Composition, Muscle Free Amino Acid Profiles and Blood Plasma Changes in Juvenile Sterlet Sturgeon, Acipenser ruthenus.

A series of studies were carried out to investigate the supplemental effects of dietary garlic extracts (GE) on whole body amino acids, whole body and muscle free amino acids, fatty acid composition and blood plasma changes in 6 month old juvenile sterlet sturgeon (Acipenser ruthenus). In the first experiment, fish with an average body weight of 59.6 g were randomly allotted to each of 10 tanks (two groups of five replicates, 20 fish/tank) and fed diets with (0.5%) or without (control) GE respectively, at the level of 2% of fish body weight per day for 5 wks. Whole body amino acid composition between the GE and control groups were not different (p>0.05). Among free amino acids in muscle, L-glutamic acid, L-alanine, L-valine, L-leucine and L-phenylalanine were significantly (p<0.05) higher in GE than in control. However, total whole body free amino acids were significantly lower in GE than in control (p<0.05). GE group showed higher EPA (C22:6n3) and DHA (C22:5n3) in their whole body than the other group (p<0.05). In the second experiment, the effects of dietary garlic extracts on blood plasma changes were investigated using 6 month old juvenile sterlet sturgeon averaging 56.5 g. Fish were randomly allotted to each of 2 tanks (300 fish/tank) and fed diets with (0.5%) or without (control) GE respectively, at the rate of 2% of body weight per day for 23 d. At the end of the feeding trial, blood was taken from the tail vein (n = 5, per group) at 1, 12, and 24 h after feeding, respectively. Blood plasma glucose, insulin and the other serological characteristics were also measured to assess postprandial status of the fish. Plasma glucose concentrations (mg/dl) between two groups (GE vs control) were significantly (p< 0.05) different at 1 (50.8 vs 62.4) and 24 h (57.6 vs 73.6) after feeding, respectively, while no significant difference (p>0.05) were noticed at 12 h (74.6 vs 73.0). Plasma insulin concentrations (µIU/ml) between the two groups were significantly (p<0.05) different at 1 (10.56 vs 5.06) and 24 h (32.56 vs 2.96) after feeding. The present results suggested that dietary garlic extracts could increase dietary glucose utilization through the insulin secretion, which result in improved fish body quality and feed utilization by juvenile sterlet sturgeon.

Effects of Dietary Garlic Extract on Growth, Feed Utilization and Whole Body Composition of Juvenile Sterlet Sturgeon (Acipenser ruthenus).

This study was carried out to investigate the supplemental effects of dietary garlic extract (GE) on growth performance of juvenile sterlet sturgeon (Acipenser ruthenus). The first experiment was designed to determine the optimum levels of garlic extract as growth promoter during 10 weeks. Three groups (two replicates/group) of 240 fish with mean body weight of 85 g were fed with diets containing 0 (control), 0.5 and 1.0% of GE. The highest weight gain (%) and feed efficiency (%) were found in fish groups fed with diet containing 0.5% GE. Subsequently, the supplemental effects of dietary GE was studied on growth of juvenile sterlet sturgeon (Acipenser ruthenus) with an average body weight of 59.6 g. Fish cultured in freshwater were randomly allotted to each of 10 tanks (two groups of five replicates, 20 fish/tank) and fed diets with 0.5% GE or without GE (control), respectively, at the level of 2.0% of fish body weight per day for 5 weeks. Weight gain (51.1%), feed efficiency (79.1%), specific growth rate (1.18%) and protein efficiency ratio (1.50) of fish fed 0.5% GE were significantly (p<0.05) higher than those fish fed the control diet. Significantly higher protein (PRE 20.4%) and lipid retention efficiencies (LRE, 74.5%) were also found in 0.5% GE group (p<0.05). The present results suggested that dietary GE could improve growth and feed utilization of juvenile sterlet sturgeons.