Time-resolved spectroscopic investigation for the practical application of a photocatalytic air purifier.

The photocatalytic efficiency for removing volatile organic compounds (VOCs) is significantly influenced by operational parameters like humidity and flow velocity, exhibiting notable and inconsistent fluctuations in both lab-scale and large-scale demonstrations. In this study, operando spectroscopy and isotope analysis were employed to investigate the correlation between humidity levels and degradation of gaseous acetaldehyde using TiO2 photocatalysts, aiming to demonstrate the scaling-up of photocatalytic air purifier. It was observed that rate constants for the mineralization of acetaldehyde rapidly decreased by 30% as relative humidity increased from 25% to 80% in the flow system (with an air velocity, v = 0.78 m/s). However, batch system showed smaller change with only a 10% reduction of the rate constant. Humidity fluctuations were more pronounced under high-speed conditions and were amplified in air purifier (v = 3.8 m/s). Time-resolved operando spectroscopy using an 13C isotope of acetaldehyde revealed that humidity's distinct role in dark adsorption and photocatalytic reactions. Water was found to inhibit the formation of crotonaldehyde during aldol condensation reaction in dark condition. Moreover, water suppressed photocatalytic mineralization by inhibiting acetate oxidation to formate. These findings provide valuable insights for improving realistic air purification processes, underscoring the importance of identifying key intermediates and controlling humidity to enhance the selectivity of gaseous pollutant oxidation reactions.

Vitamin C-induced CO2 capture enables high-rate ethylene production in CO2 electroreduction.

High-rate production of multicarbon chemicals via the electrochemical CO2 reduction can be achieved by efficient CO2 mass transport. A key challenge for C-C coupling in high-current-density CO2 reduction is how to promote *CO formation and dimerization. Here, we report molecularly enhanced CO2-to-*CO conversion and *CO dimerization for high-rate ethylene production. Nanoconfinement of ascorbic acid by graphene quantum dots enables immobilization and redox reversibility of ascorbic acid in heterogeneous electrocatalysts. Cu nanowire with ascorbic acid nanoconfined by graphene quantum dots (cAA-CuNW) demonstrates high-rate ethylene production with a Faradaic efficiency of 60.7% and a partial current density of 539 mA/cm2, a 2.9-fold improvement over that of pristine CuNW. Furthermore, under low CO2 ratio of 33%, cAA-CuNW still exhibits efficient ethylene production with a Faradaic efficiency of 41.8%. We find that cAA-CuNW increases *CO coverage and optimizes the *CO binding mode ensemble between atop and bridge for efficient C-C coupling. A mechanistic study reveals that ascorbic acid can facilitate *CO formation and dimerization by favorable electron and proton transfer with strong hydrogen bonding.

Transplanting Gold Active Sites into Non-Precious-Metal Nanoclusters for Efficient CO2-to-CO Electroreduction.

Electrocatalytic CO2 reduction reaction (CO2RR) is greatly facilitated by Au surfaces. However, large fractions of underlying Au atoms are generally unused during the catalytic reaction, which limits mass activity. Herein, we report a strategy for preparing efficient electrocatalysts with high mass activities by the atomic-level transplantation of Au active sites into a Ni4 nanocluster (NC). While the Ni4 NC exclusively produces H2, the Au-transplanted NC selectively produces CO over H2. The origin of the contrasting selectivity observed for this NC is investigated by combining operando and theoretical studies, which reveal that while the Ni sites are almost completely blocked by the CO intermediate in both NCs, the Au sites act as active sites for CO2-to-CO electroreduction. The Au-transplanted NC exhibits a remarkable turnover frequency and mass activity for CO production (206 molCO/molNC/s and 25,228 A/gAu, respectively, at an overpotential of 0.32 V) and high durability toward the CO2RR over 25 h.

Harnessing Waste Heat from Indoor lamps for Sustainable Thermocatalytic Mineralization of Acetaldehyde using Platinized TiO2.

This study demonstrates the first reported thermocatalytic oxidation of an indoor volatile organic compound (VOC), acetaldehyde, by harnessing the waste-heat energy from indoor light sources (e.g., halogen lamps) without additional energy inputs. With an optimal Pt-TiO2 catalyst, the designed catalyst-coated lampshade was successfully activated under waste-heat energy (∼120 °C) and achieved the complete mineralization of CH3CHO into CO2 (k = 0.02 min-1). The catalytic activity of Pt-TiO2 was extremely dependent on its preparation method which greatly influenced the characteristics (e.g., oxidation state and size) of Pt. The thermocatalytic oxidation mechanism of CH3CHO over Pt-TiO2 was investigated, which revealed that O2 and H2O sources play vital roles. Although Pt is an expensive noble metal, the thermocatalytic process on the Pt-TiO2-coated lampshade without additional energy, along with its outstanding activity, can offset the high material cost. The proposed strategy offers a sustainable and feasible method for the degradation of indoor VOCs.

Investigation of the AgCl Formation Mechanism on the Ag Wire Surface for the Fabrication of a Marine Low-Frequency-Electric-Field-Detection Ag/AgCl Sensor Electrode.

One of the most widely used electric field sensors for low-frequency electric field detection (LFEFD) in seawater uses the Ag/AgCl electrode. The surface structure of the electrode including AgCl layers plays a critical role in the electrode's electrochemical performance required for the sensor. In this study, the sequential AgCl formation process under the constant current was examined on the Ag wire in an electrode size for actual applications, and an optimal electrode surface structure was suggested for the LFEFD Ag/AgCl sensor. Upon mild anodization (0.2 mA/cm2) in 3.3 M KCl solution that permits us to follow the AgCl formation process manageably, Ag dissolution from the wire surface begins leaving cavities on the surface, with the accompanied growth of initial Ag grains. During this period, AgCl deposits in sizes of about several micrometers to 10 µm with crystal planes also form primarily along scratch lines on the wire surface, but in a partial scale. Then, with further anodization, the assumed thin AgCl deposits start to form, covering a large portion of the wire surface. They grow to become deposits in sizes of about several micrometers to 10 µm with no clear facet planes next to one another and are connected to form the network structure, representing the main developing mode of the AgCl deposits. While they cover all the surface, AgCl deposits also form on the surface of the already formed ones, making multiple AgCl layers. All these deposits develop through the nucleation process with a relatively high surface energy barrier, and their formation rate is solely controlled by the release rate of Ag+ from the wire, thus by the applied current magnitude. The Ag/AgCl electrode with a thick AgCl layer and many holes in the AgCl surface structure like microchannels is considered to work effectively for the LFEFD sensor in terms of both detection sensitivity and service lifetime.

Erosion-Driven Enamel Crystallite Growth Phenomenon at the Tooth Surface In Vitro.

The erosion of tooth enamel is a common oral disease. The erosion pattern and location and the effects of nanoscale chemical composition on the erosion susceptibility of enamel have been well documented. However, the enamel remineralization accompanied by erosion and its underlying physicochemical mechanisms still remain poorly understood. Here, using rat molars selected for its good relevancy to human teeth, we investigated the remineralization behavior of the outermost enamel surface at the nanoscale level during erosion in diluted hydrochloric acid solutions. While particles on the outermost enamel surface that represent the termination of crystallites protruding to the surface from the near-surface core eroded by acid-attack, the lateral-growth of the particles (i.e., the main remineralization picture of the surface enamel) occurred concurrently. Ionic analyses indicate that the particle growth is driven by the local increase in pH near the eroding enamel surface as a result of the combination of the PO43- and CO32- released from the enamel surface with H+. As the pH increases eventually to the equilibrium pH level (∼5.5), a local supersaturation of solute ions is induced, resulting in particle growth. A simple growth model based on the experimental results together with an assumption that the particle growth is a diffusional process suggests that the particle growth rate is controlled by the degree of supersaturation and accommodation site for solute ions, which are affected by the pH of solution eroding the enamel surface. The remineralization mechanism presented by our study can explain how the enamel on being acid-exposed or tooth decay progress by beverage or food can naturally remineralize in the oral cavity and how remineralization can foster different surface topology at the nanoscale, depending on the pH value of etchant before the dental filling material is applied.

Visible-Light Activation of a Dissolved Organic Matter-TiO2 Complex Mediated via Ligand-to-Metal Charge Transfer.

Given the widespread use of TiO2, its release into aquatic systems and complexation with dissolved organic matter (DOM) are highly possible, making it important to understand how such interactions affect photocatalytic activity under visible light. Here, we show that humic acid/TiO2 complexes (HA/TiO2) exhibit photoactivity (without significant electron-hole activation) under visible light through ligand-to-metal charge transfer (LMCT). The observed visible-light activities for pollutant removal and bacterial inactivation are primarily linked to the generation of H2O2via the conduction band. By systematically considering molecular-scale interactions between TiO2 and organic functional groups in HA, we find a key role of phenolic groups in visible-light absorption and H2O2 photogeneration. The photochemical formation of H2O2 in river waters spiked with TiO2 is notably elevated above naturally occurring H2O2 generated from background organic constituents due to LMCT contribution. Our findings suggest that H2O2 generation by HA/TiO2 is related to the quantity and functional group chemistry of DOM, which provides chemical insights into photocatalytic activity and potential ecotoxicity of TiO2 in environmental and engineered systems.

Changes in levels of N-nitrosamine formed from amine-containing compounds during chloramination via photocatalytic pretreatment with immobilized TiO2: Effect of source water and pH.

We investigated the effectiveness of photocatalytic pretreatment (PCP) of precursors in minimizing the formation potentials (FPs) of carcinogenic nitrosamines, including N-nitrosodimethylamine (NDMA), N-nitrosodiethylamine (NDEA), and N-nitrosodiethanolamine (NDELA), during water chloramination. A steel mesh substrate with immobilized TiO2 was highly efficient at mitigating nitrosamine formation and removing targeted precursors such as ranitidine, nizatidine, trimebutine, triethanolamine, and metoclopramide. Compared to UVC/H2O2, PCP under UVA irradiation (intensity of 0.67 mW cm-2) was more effective for reducing nitrosamine-FPs during post-chloramination. However, the PCP efficacies varied with the water source, pretreatment pH, and irradiation time. For example, PCP of eutrophic water increased the NDMA-FPs, but produced notable reductions (up to 99%) for NDELA- and NDEA-FPs. Shorter irradiation times, up to 15 min, increased the NDELA-FP in triethanolamine, and the NDMA-FP in nizatidine and trimebutine. However, the nitrosamine-FP decreased by > 50% after PCP at a pH > 5.6, following irradiation for 120 min. Oxygen addition, N-de(m)ethylation, and N-dealkylation were responsible for decreasing nitrosamine-FPs via the destruction of key moieties; this has been elucidated by mass spectroscopy. This study suggests that PCP could be used as an alternative strategy for minimizing nitrosamine-FPs during water treatment.

Photocatalytic exoskeleton: Chitin nanofiber for retrievable and sustainable TiO2 carriers for the decomposition of various pollutants.

Loading a photocatalytic TiO2 to organic carriers has been desired for volumetric TiO2 incorporation, facile retrieval, and sustainable utilization. Traditionally, suspended TiO2 nanoparticles or its thin film on two-dimensional substrate are popularly fabricated for pollutants decomposition without carriers; due to poor thermomechanical properties of the organic carriers. Herein, a combination of the chitin nanofiber carrier and atomic layer deposition proves relevance for formation of anatase TiO2 thin layer so that photocatalytic decomposition in three-dimensional surface. Moreover, chitin nanofiber is capable of holding the TiO2 nanoparticles for multiple cycles of photocatalysis. Those types of TiO2 show characteristic degradation performance for gaseous (acetaldehyde) and aqueous pollutants (4-chlorophenol and rhodamine B). After catalytic reaction, chitin/TiO2 is retrievable owing to carrier's robustness even in water without TiO2 aggregation and loss. This work suggests that chitin-based photocatalyst is applicable to numerous pollutants through chitin's relatively high chemical resistance and stably wedged TiO2 during photocatalytic reaction.

Selective electrochemical reduction of nitric oxide to hydroxylamine by atomically dispersed iron catalyst.

Electrocatalytic conversion of nitrogen oxides to value-added chemicals is a promising strategy for mitigating the human-caused unbalance of the global nitrogen-cycle, but controlling product selectivity remains a great challenge. Here we show iron-nitrogen-doped carbon as an efficient and durable electrocatalyst for selective nitric oxide reduction into hydroxylamine. Using in operando spectroscopic techniques, the catalytic site is identified as isolated ferrous moieties, at which the rate for hydroxylamine production increases in a super-Nernstian way upon pH decrease. Computational multiscale modelling attributes the origin of unconventional pH dependence to the redox active (non-innocent) property of NO. This makes the rate-limiting NO adsorbate state more sensitive to surface charge which varies with the pH-dependent overpotential. Guided by these fundamental insights, we achieve a Faradaic efficiency of 71% and an unprecedented production rate of 215 µmol cm-2 h-1 at a short-circuit mode in a flow-type fuel cell without significant catalytic deactivation over 50 h operation.

Unusual Hole Transfer Dynamics of the NiO Layer in Methylammonium Lead Tri-iodide Absorber Solar Cells.

Nickel oxides (NiO) as hole transport layers (HTLs) in inverted-type perovskite solar cells (PSCs) have been widely studied mainly because of their high stability under illumination. Increases in the power conversion efficiency (PCE) with NiO HTLs have been presented in numerous reports, although the photoluminescence (PL) quenching behavior does not coincide with the PCE increase. The dynamics of the charge carrier transport between the NiO HTLs and the organic-inorganic halide perovskite absorbers is not clearly understood yet and quite unusual, in contrast to organic/polymerics HTLs. We deposited NiO HTLs with precisely controlled thicknesses by atomic layer deposition (ALD) and studied their photovoltaic performances and hole transfer characteristics. Ground state bleaching (GSB) recovery was observed by ultrafast transient absorption spectroscopy (TAS), which suggested that backward hole injection occurred between the perovskites and NiO HTLs, so that the uncommon PL behaviors can be clearly explained. Backward hole injection from the NiO HTL to the perovskite absorber originated from their similar valence band (VB) energy positions. The thickness increase of the NiO HTLs induced VB sharing, which caused a red-shift of the photoinduced hole absorption spectrum in near-infrared (NIR) femtosecond TAS and a decrease in the PL intensity. Our studies on inorganic metal oxide transport layers, NiO in this work, with a thickness dependence and the comparison with organic layers provide a better understanding of the interfacial carrier dynamics in PSCs.

Unexpected discovery of superoxide radical generation by oxygen vacancies containing biomass derived granular activated carbon.

Herein, we discovered and reported oxygen vacancies in silicon oxycarbide containing granular palm shell activated carbon (Si-PSAC) as a photocatalyst under UV irradiation. A strong correlation between the atomic content of Si1+, oxygen vacancies and photocatalytic performance of Si-PSAC was obtained. Based on the electron paramagnetic resonance and photoluminescence analyses, Si-PSAC under UVA365 irradiation exhibited a higher donor density, better charge transfer and lower electron-hole recombination than that under the other light sources, leading to a higher O2· production efficiency. Si-PSAC exhibited effective removal performance for various anionic dyes and endocrine-disrupting chemicals under UVA365 irradiation. Continuous-flow column tests revealed the life span of Si-PSAC under UVA365 irradiation was extended by more than 16-fold compared to adsorption column. Since the oxygen vacancies can be created from the naturally present Si in the biomass derived Si-PSAC during the activation, this unexpected discovery of O2· production can extend commercially-available Si-PSAC into the full-scale photocatalysis.

Oxygen vacancy engineering of cerium oxide for the selective photocatalytic oxidation of aromatic pollutants.

The engineering of oxygen vacancies in CeO2 nanoparticles (NPs) allows the specific fine-tuning of their oxidation power, and this can be used to rationally control their activity and selectivity in the photocatalytic oxidation (PCO) of aromatic pollutants. In the current study, a facile strategy for generating exceptionally stable oxygen vacancies in CeO2 NPs through simple acid (CeO2-A) or base (CeO2-B) treatment was developed. The selective (or mild) PCO activities of CeO2-A and CeO2-B in the degradation of a variety of aromatic substrates in water were successfully demonstrated. CeO2-B has more oxygen vacancies and exhibits superior photocatalytic performance compared to CeO2-A. Control of oxygen vacancies in CeO2 facilitates the adsorption and reduction of dissolved O2 due to their high oxygen-storage ability. The oxygen vacancies in CeO2-B as active sites for oxygen-mediated reactions act as (i) adsorption and reduction reaction sites for dissolved O2, and (ii) photogenerated electron scavenging sites that promote the formation of H2O2 by multi-electron transfer. The oxygen vacancies in CeO2-B are particularly stable and can be used repeatedly over 30 h without losing activity. The selective PCOs of organic substrates were studied systematically, revealing that the operating mechanisms for UV-illuminated CeO2-B are very different from those for conventional TiO2 photocatalysts. Thus, the present study provides new insights into the design of defect-engineered metal oxides for the development of novel photocatalysts.

Detailed Characterization of an Annealed Reduced Graphene Oxide Catalyst for Selective Peroxide Formation Activity.

Recently, electrochemical hydrogen peroxide (H2O2) generation from oxygen molecules has been extensively studied. Thus far, the best peroxide activity under alkaline conditions has been reported at the surface of a mild reduced graphene oxide annealed at 600 °C (mrGO-600). However, the detailed material information, such as chemical functionality and structural morphology, is unknown, which results in ambiguous debates on its catalytic active sites. To solve this problem, we intensively characterize the structure of mrGO-600 to clarify the origin of its catalytic activity. Various characterizations, including X-ray photoelectron spectroscopy, Raman spectroscopy, infrared spectroscopy, near-edge X-ray absorption fine spectroscopy, and high-resolution transmittance electron microscopy coupled with in situ infrared spectroelecrochemistry, reveal that the annealing process generates not only various hole edge defects that are related to the ring ether group but also numerous point defects that result in a small-sized disconnected graphitic carbon region. These defects are believed to form a unique atomic level configuration in mrGO-600, which enables it to facilitate high peroxide-generated activity from oxygen molecules in an alkaline electrolyte.

Ag(I) ions working as a hole-transfer mediator in photoelectrocatalytic water oxidation on WO3 film.

Ag(I) is commonly employed as an electron scavenger to promote water oxidation. In addition to its straightforward role as an electron acceptor, Ag(I) can also capture holes to generate the high-valent silver species. Herein, we demonstrate photoelectrocatalytic (PEC) water oxidation and concurrent dioxygen evolution by the silver redox cycle where Ag(I) acts as a hole-transfer mediator. Ag(I) enhances the PEC performance of WO3 electrodes at 1.23 V vs. RHE with increasing O2 evolution, while forming Ag(II) complexes (AgIINO3+). Upon turning off both light and potential bias, the photocurrent immediately drops to zero, whereas O2 evolution continues over ~10 h with gradual bleaching of the colored complexes. This phenomenon is observed neither in the Ag(I)-free PEC reactions nor in the photocatalytic (i.e., bias-free) reactions with Ag(I). This study finds that the role of Ag(I) is not limited as an electron scavenger and calls for more thorough studies on the effect of Ag(I).

Formation of TiO2@Carbon Core/Shell Nanocomposites from a Single Molecular Layer of Aromatic Compounds for Photocatalytic Hydrogen Peroxide Generation.

In this article, we demonstrate that TiO2@carbon core/shell (TiO2@C) nanocomposite photocatalysts prepared by carbonizing a single molecular layer of aromatic compounds adsorbed on the surface of TiO2 nanoparticles selectively enhance the generation of hydrogen peroxide (H2O2). Atomically thin carbon shells have been formed directly on the surface of TiO2 nanoparticles through pyrolytic decarboxylation of the adsorbed aromatic compounds, benzoic acid (BA), and 1-naphthoic acid (NA), which yields two types of TiO2@C nanocomposites, TiO2@C(BA) and TiO2@C(NA). Raman spectroscopy shows that the as-obtained nanocomposites have similar degrees of graphitization (D/G band ratio), regardless of the type of aromatic precursors, but TiO2@C(NA) contains more oxygenic species than TiO2@C(BA) (D*/G band ratio). Such oxygenic species predominantly exist in the form of epoxide groups, as determined by attenuated total reflection infrared spectroscopy. The sp2 carbon atoms near the epoxide groups in the carbon shell can act as active sites for the two-electron reduction of O2. Therefore, TiO2@C(NA) can generate H2O2 more efficiently than TiO2@C(BA). Furthermore, the carbon shells retard the reconsumption of the generated H2O2 by inhibiting the adsorption of H2O2 on the surface of TiO2 nanoparticles, thereby improving the photocatalytic efficiency of H2O2 generation. Finally, we have shown the durability and reproducibility of our TiO2@C-based photocatalytic systems. We believe that our research may offer a potentially improved strategy for H2O2 generation and other photocatalytic applications.

Thorn-like TiO2 nanoarrays with broad spectrum antimicrobial activity through physical puncture and photocatalytic action.

To overcome the conventional limitation of TiO2 disinfection being ineffective under light-free conditions, TiO2 nanowire films (TNWs) were prepared and applied to bacterial disinfection under dark and UV illumination. TNW exhibited much higher antibacterial efficiencies against Escherichia coli (E. coli) under dark and UV illumination conditions compared to TiO2 nanoparticle film (TNP) which was almost inactive in the dark, highlighting the additional contribution of the physical interaction between bacterial membrane and NWs. Such a physical contact-based antibacterial activity was related to the NW geometry such as diameter, length, and density. The combined role of physical puncture and photocatalytic action in the mechanism underlying higher bactericidal effect of TNW was systematically examined by TEM, SEM, FTIR, XPS, and potassium ion release analyses. Moreover, TNW revealed antimicrobial activities in a broad spectrum of microorganisms including Staphylococcus aureus and MS2 bacteriophage, antibiofilm properties, and good material stability. Overall, we expect that the free-standing and antimicrobial TNW is a promising agent for water disinfection and biomedical applications in the dark and/or UV illumination.

Organometallic Iridium(III) Complex Sensitized Ternary Hybrid Photocatalyst for CO2 to CO Conversion.

A series of heteroleptic iridium(III) complexes functionalized with two phosphonic acid (-PO3 H2 ) groups (dfppy IrP, ppy IrP, btp IrP, and piq IrP) were prepared and anchored onto rhenium(I) catalyst (ReP)-loaded TiO2 particles (TiO2 /ReP) to build up a new IrP-sensitized TiO2 photocatalyst system (IrP/TiO2 /ReP). The photosensitizing behavior of the IrP series was examined within the IrP/TiO2 /ReP platform for the photocatalytic conversion of CO2 into CO. The four IrP-based ternary hybrids showed increased conversion activity and durability than that of the corresponding homo- (IrP+ReP) and heterogeneous (IrP+TiO2 /ReP) mixed systems. Among the four IrP/TiO2 /ReP photocatalysts, the low-energy-light (>500 nm) activated piq IrP immobilized ternary system (piq IrP/TiO2 /ReP) exhibited the most durable conversion activity, giving a turnover number of ≥730 for 170 h. A similar kinetic feature observed through time-resolved photoluminescence measurements of both btp IrP/TiO2 and TiO2 -free btp IrP films suggests that the net electron flow in the ternary hybrid proceeds dominantly through a reductive quenching mechanism, unlike the oxidative quenching route of typical dye/TiO2 -based photolysis.

Black phosphorene as a hole extraction layer boosting solar water splitting of oxygen evolution catalysts.

As the development of oxygen evolution co-catalysts (OECs) is being actively undertaken, the tailored integration of those OECs with photoanodes is expected to be a plausible avenue for achieving highly efficient solar-assisted water splitting. Here, we demonstrate that a black phosphorene (BP) layer, inserted between the OEC and BiVO4 can improve the photoelectrochemical performance of pre-optimized OEC/BiVO4 (OEC: NiOOH, MnOx, and CoOOH) systems by 1.2∼1.6-fold, while the OEC overlayer, in turn, can suppress BP self-oxidation to achieve a high durability. A photocurrent density of 4.48 mA·cm-2 at 1.23 V vs reversible hydrogen electrode (RHE) is achieved by the NiOOH/BP/BiVO4 photoanode. It is found that the intrinsic p-type BP can boost hole extraction from BiVO4 and prolong holes trapping lifetime on BiVO4 surface. This work sheds light on the design of BP-based devices for application in solar to fuel conversion, and also suggests a promising nexus between semiconductor and electrocatalyst.

Ostwald Ripening Driven Exfoliation to Ultrathin Layered Double Hydroxides Nanosheets for Enhanced Oxygen Evolution Reaction.

As a key half-reaction in water splitting, the oxygen evolution reaction (OER) process is kinetically sluggish. Layered double hydroxides (LDHs) are regarded as the highly promising electrocatalysts to promote the OER kinetics. However, the closely stacking layered structure of pristine bulk LDHs restricts the exposure of electrocatalytically active sites, and it remains a great challenge to find an efficient strategy to exfoliate the bulk LDHs into ultrathin and stable nanosheets with increased surface area and exposed active sites. Herein, a novel Ostwald ripening driven exfoliation (ORDE) of NiFe LDHs has been achieved in situ on the electrodes by spontaneously self-etching and redepositing via a simple hydrothermal treatment without the assistance of any exfoliating reagent or surfactant. The thermodynamically driven Ostwald ripening has been expanded to the exfoliation of two-dimensional layered materials for the first time. Compared with conventional exfoliation methods, this ORDE is a time-saving and green strategy that avoids the serious adsorption of surfactant molecules. The ORDE of NiFe LDHs is accomplished in situ on a Cu mesh electrode, which not only exhibits excellent electrical contact between LDHs catalyst and electrodes but also prevents the restacking of the exfoliated LDHs. As a result, the exfoliated ultrathin, clean, and vertically aligned NiFe nanosheets with much higher surface area and numerous exposed active edges and sites demonstrated significantly enhanced OER performances with low overpotential of 292 mV at 10 mA cm-2 and long-term stability for more than 60 h, as well as remarkable flexibility. Additionally, bulk Ni(OH)2 nanosheets on Ni foams have also been exfoliated by a similar mechanism, indicating this ORDE strategy can be widely extended to other 2D layered materials for novel applications.