ABSTRACT
The developments in manufacturing technologies are expected to reduce energy input without compromising product quality. Regarding the material densification process, numerical simulation methods are applied to achieve this goal. In this case, relevant material models are built using functions that describe the variation in mechanical parameters of the material in question due to its deformation. The literature review conducted for this research has revealed a shortage of experimental research methods allowing a determination of the coefficient of friction at low temperatures, approximately 200 K. This article proposes a method for determining the friction coefficient of dry ice sliding against steel. The experimental results were analysed to obtain several functions describing the variation in the coefficient of friction. These functions were then compared using goodness-of-fit indexes. Finally, two functions with similar goodness-of-fit values were chosen. The findings of this research project will complement the already available information and may be used in various research and implementation projects related to the development or improvement of currently used crystallised carbon dioxide conversion processes.
ABSTRACT
This article aims to compare the behaviour of four types of lattice structures named Cartesian, Rhomboid, Octagonal, and Starlit under tensile stress loading. The structures were made of Acrylonitrile Butadiene Styrene (ABS) material using the Fused Filament Fabrication (FFF) technique with three different specific volumes (24, 42, and 60%). Five samples of each type were produced, and a total of 60 samples were tested. Experimental testing was performed according to EN ISO 527-1:2012 and EN ISO 527-2:2012. The obtained data were statistically processed, while no outliers were identified. The experimental results pointed out that the specimens' topology, together with the specific volume, very significantly affected the resultant ABS properties of the tested samples made of the same material. The comparative study showed that in terms of ultimate strength, yield strength, and Young's modulus, the Cartesian structure appeared to be the most suitable for tensile stress, and the least suitable structure was the Rhomboid structure. On the other hand, the Rhomboid-type of the structure showed not only the highest amount of absorbed energy but also the highest toughness among the investigated lattice structures, so in the near future, its behaviour under an impact test should be studied.
ABSTRACT
Polyvinyl butyral (PVB) is a thermoplastic resin commonly used as an interlayer material in laminated glass. Combined with textile fibres from worn tyres, PVB can produce a composite material with unique properties. One such property is absorption. Absorption in textile fibre composite materials refers to the ability of the material to absorb or retain moisture or other fluids. The presence of moisture or liquids can affect the properties of composite materials, such as their strength, stiffness, and dimensional stability. As a result of the physical and chemical action of the environment, corrosion of plastics occurs and manifests itself in changes in appearance, surface quality, weight, dimensions, and also in changes in other properties. This paper investigates four composite materials with different fabrics content. The aim of this paper is to propose a generalized mathematical model for absorption values so that, with different ratios of textile fibre in the material, its quality indicators are at a sufficient level. Our study will proceed from the assumption that by changing the values of the individual coefficients of the selected model based on their analysis, we will achieve the required qualitative indicators.
ABSTRACT
The resulting quality of castings indicates the correlation of the design of the mold inlet system and the setting of technological parameters of casting. In this study, the influence of design solutions of the inlet system in a pressure mold on the properties of Al-Si castings was analyzed by computer modelling and subsequently verified experimentally. In the process of computer simulation, the design solutions of the inlet system, the mode of filling the mold depending on the formation of the casting and the homogeneity of the casting represented by the formation of shrinkages were assessed. In the experimental part, homogeneity was monitored by X-ray analysis by evaluating the integrity of the casting and the presence of pores. Mechanical properties such as permanent deformation and surface hardness of castings were determined experimentally, depending on the height of the inlet notch. The height of the inlet notch has been shown to be a key factor, significantly influencing the properties of the die-cast parts and influencing the speed and filling mode of the mold cavity. At the same time, a significant correlation between porosity and mechanical properties of castings is demonstrated. With the increasing share of porosity, the values of permanent deformation of castings increased. It is shown that the surface hardness of castings does not depend on the integrity of the castings but on the degree of subcooling of the melt in contact with the mold and the formation of a fine-grained structure in the peripheral zones of the casting.