Reduction of biofilm accumulation by constant and alternating potentials in static and dynamic field experiments.

The application of electric fields to conductive coatings is an environmentally friendly way to reduce biofilm formation. In particular alternating potentials (APs) have received increasing attention in recent studies. Here, an electrochemical rotating disk setup for dynamic field exposure experiments was developed to study how APs alter the attachment of fouling organisms in a multispecies ocean environment. A specific focus of the device design was proper integration of the potentiostat in the strongly corroding saltwater environment. The effect of APs on the accumulation of fouling organisms in short term field exposures was studied. Potentials on conductive gold surfaces were periodically switched between -0.3 V and 0.3 V or between -0.8 V and 0.6 V at a frequency of 0.5 Hz. APs were capable of significantly reducing the attachment of marine fouling organisms compared with the conductive samples immersed at open circuit potentials.

Low Fouling Polysulfobetaines with Variable Hydrophobic Content.

Amphiphilic polymer coatings combining hydrophilic elements, in particular zwitterionic groups, and hydrophobic elements comprise a promising strategy to decrease biofouling. However, the influence of the content of the hydrophobic component in zwitterionic coatings on the interfacial molecular reorganization dynamics and the anti-fouling performance is not well understood. Therefore, coatings of amphiphilic copolymers of sulfobetaine methacrylate 3-[N-2'-(methacryloyloxy)ethyl-N,N-dimethyl]-ammonio propane-1-sulfonate (SPE) are prepared which contain increasing amounts of hydrophobic n-butyl methacrylate (BMA). Their fouling resistance is compared to that of their homopolymers PSPE and PBMA. The photo-crosslinked coatings form hydrogel films with a hydrophilic surface. Fouling by the proteins fibrinogen and lysozyme as well as by the diatom Navicula perminuta and the green algae Ulva linza is assessed in laboratory assays. While biofouling is strongly reduced by all zwitterionic coatings, the best fouling resistance is obtained for the amphiphilic copolymers. Also in preliminary field tests, the anti-fouling performance of the amphiphilic copolymer films is superior to that of both homopolymers. When the coatings are exposed to a marine environment, the reduced susceptibility to silt incorporation, in particular compared to the most hydrophilic polyzwitterion PSPE, likely contributes to the improved fouling resistance.

Sulfobetaine Methacrylate Polymers of Unconventional Polyzwitterion Architecture and Their Antifouling Properties.

Combining high hydrophilicity with charge neutrality, polyzwitterions are intensely explored for their high biocompatibility and low-fouling properties. Recent reports indicated that in addition to charge neutrality, the zwitterion's segmental dipole orientation is an important factor for interacting with the environment. Accordingly, a series of polysulfobetaines with a novel architecture was designed, in which the cationic and anionic groups of the zwitterionic moiety are placed at equal distances from the backbone. They were investigated by in vitro biofouling assays, covering proteins of different charges and model marine organisms. All polyzwitterion coatings reduced the fouling effectively compared to model polymer surfaces of poly(butyl methacrylate), with a nearly equally good performance as the reference polybetaine poly(3-(N-(2-(methacryloyloxy)ethyl)-N,N-dimethylammonio)propanesulfonate). The specific fouling resistance depended on the detailed chemical structure of the polyzwitterions. Still, while clearly affecting the performance, the precise dipole orientation of the sulfobetaine group in the polyzwitterions seems overall to be only of secondary importance for their antifouling behavior.

Sol-Gel-Based Hybrid Materials as Antifouling and Fouling-Release Coatings for Marine Applications.

Hybrid materials (HMs) offer unique properties as they combine inorganic and organic components into a single material. Here, we developed HM coatings for marine antifouling applications using sol-gel chemistry and naturally occurring polysaccharides. The coatings were characterized by spectroscopic ellipsometry, contact angle goniometry, AFM, and ATR-FTIR, and their stability was tested in saline media. Marine antifouling and fouling-release properties were tested in laboratory assays against the settlement of larvae of the barnacle Balanus improvisus and against the settlement and removal of the diatom Navicula incerta. Furthermore, laboratory data were confirmed in short-term dynamic field assays in Florida, USA. All hybrid coatings revealed a superior performance in the assays compared to a hydrophobic reference. Within the hybrids, those with the highest degree of hydrophilicity and negative net charge across the surface performed best. Alginate and heparin showed good performance, making these hybrid materials promising building blocks for fouling-resistant coatings.

Effect of Dipole Orientation in Mixed, Charge-Equilibrated Self-assembled Monolayers on Protein Adsorption and Marine Biofouling.

While zwitterionic interfaces are known for their excellent low-fouling properties, the underlying molecular principles are still under debate. In particular, the role of the zwitterion orientation at the interface has been discussed recently. For elucidation of the effect of this parameter, self-assembled monolayers (SAMs) on gold were prepared from stoichiometric mixtures of oppositely charged alkyl thiols bearing either a quaternary ammonium or a carboxylate moiety. The alkyl chain length of the cationic component (11-mercaptoundecyl)-N,N,N-trimethylammonium, which controls the distance of the positively charged end group from the substrate's surface, was kept constant. In contrast, the anionic component and, correspondingly, the distance of the negatively charged carboxylate groups from the surface was varied by changing the alkyl chain length in the thiol molecules from 7 (8-mercaptooctanoic acid) to 11 (12-mercaptododecanoic acid) to 15 (16-mercaptohexadecanoic acid). In this way, the charge neutrality of the coating was maintained, but the charged groups exposed at the interface to water were varied, and thus, the orientation of the dipoles in the SAMs was altered. In model biofouling studies, protein adsorption, diatom accumulation, and the settlement of zoospores were all affected by the altered charge distribution. This demonstrates the importance of the dipole orientation in mixed-charged SAMs for their inertness to nonspecific protein adsorption and the accumulation of marine organisms. Overall, biofouling was lowest when both the anionic and the cationic groups were placed at the same distance from the substrate's surface.

Fully Convolutional Neural Network for Detection and Counting of Diatoms on Coatings after Short-Term Field Exposure.

While the use of deep learning is a valuable technology for automatic detection systems for medical data and images, the biofouling community is still lacking an analytical tool for the detection and counting of diatoms on samples after short-term field exposure. In this work, a fully convolutional neural network was implemented as a fast and simple approach to detect diatoms on two-channel (fluorescence and phase-contrast) microscopy images by predicting bounding boxes. The developed approach performs well with only a small number of trainable parameters and a F1 score of 0.82. Counting diatoms was evaluated on a data set of 600 microscopy images of three different surface chemistries (hydrophilic and hydrophobic) and is very similar to counting by humans while demanding only a fraction of the analysis time.

Effects of crosslink density in zwitterionic hydrogel coatings on their antifouling performance and susceptibility to silt uptake.

Hydrogel coatings effectively reduce the attachment of proteins and organisms in laboratory assays, in particular when made from zwitterionic monomers. In field experiments with multiple species and non-living material, such coatings suffer from adsorption of particulate matter. In this study, the zwitterionic monomer 3-[N-(2-methacryloyloxyethyl)-N,N-dimethylammonio] propanesulfonate (SPE) was copolymerized with increasing amounts of the photo-crosslinker benzophenon-4-yloxyethyl methacrylate (BPEMA) to systematically alter the density of crosslinks between the polymer chains. The effect of increasing crosslink density on the antifouling (AF) performance of the coatings was investigated in laboratory assays and fields tests. In both cases, the AF performance was improved by increasing the crosslinker content. The coatings reduced protein, diatom, and barnacle accumulation, and showed better resistance to biomass accumulation. The findings underline that the marine AF performance of hydrogel coatings does not only depend on the specific chemical structure of the polymers, but also on their physico-chemical properties such as rigidity and swelling.

Amphiphilic Dicyclopentenyl/Carboxybetaine-Containing Copolymers for Marine Fouling-Release Applications.

Zwitterionic materials received great attention in recent studies due to their high antifouling potential, though their application in practical coatings is still challenging. Amphiphilic polymers have been proven to be an effective method to combat fouling in the marine environment. This study reports the incorporation of small amounts of zwitterionic carboxybetaine methacrylate (CBMA) into hydrophobic ethylene glycol dicyclopentenyl ether acrylate (DCPEA). A new set of copolymers with varying amphiphilicities was synthesized and coated on chemically modified glass substrates. The antifouling capabilities were assessed against the diatom Navicula perminuta and multiple species in the field. Unsurprisingly, high diatom densities were observed on the hydrophobic control coatings. The integration of small zwitterionic contents of only ∼5 wt % was already sufficient to rapidly form a hydrophilic interface that led to a strong reduction of fouling. Ultralow fouling was also observed for the pure zwitterionic coatings in laboratory experiments, but it failed when tested in the real ocean environment. We noticed that the ability to absorb large amounts of water and the diffuse nature of the interphase correlate with the adsorption of silt, which can mask the hydrophilic chemistries and facilitate the settlement of organisms. The amphiphilic coatings showed low fouling in dynamic short-term field exposures, which could be explained by the reduced tendency of the coatings for sediment adsorption.

Synthesis of Novel Sulfobetaine Polymers with Differing Dipole Orientations in Their Side Chains, and Their Effects on the Antifouling Properties.

The impact of the orientation of zwitterionic groups, with respect to the polymer backbone, on the antifouling performance of thin hydrogel films made of polyzwitterions is explored. In an extension of the recent discussion about differences in the behavior of polymeric phosphatidylcholines and choline phosphates, a quasi-isomeric set of three poly(sulfobetaine methacrylate)s is designed for this purpose. The design is based on the established monomer 3-[N-2-(methacryloyloxy)ethyl-N,N-dimethyl]ammonio-propane-1-sulfonate and two novel sulfobetaine methacrylates, in which the positions of the cationic and the ionic groups relative to the polymerizable group, and thus also to the polymer backbone, are altered. The effect of the varied segmental dipole orientation on their water solubility, wetting behavior by water, and fouling resistance is compared. As model systems, the adsorption of the model proteins bovine serum albumin (BSA), fibrinogen, and lysozyme onto films of the various polyzwitterion surfaces is studied, as well as the settlement of a diatom (Navicula perminuta) and barnacle cyprids (Balanus improvisus) as representatives of typical marine fouling communities. The results demonstrate the important role of the zwitterionic group's orientation on the polymer behavior and fouling resistance.

Layer-by-layer constructed hyaluronic acid/chitosan multilayers as antifouling and fouling-release coatings.

Polyelectrolyte multilayers (PEMs) consisting of hyaluronic acid (HA) and chitosan (Ch) are extensively studied for biomedical applications and suppress bacterial and protein attachment. Here, we prepared and tested HA/Ch PEMs as marine fouling-release coatings. PEMs were constructed by layer-by-layer assembly using spin coating. The multilayers were crosslinked for enhanced stability in the sea water environment by chemical and thermal treatment. Protein-repelling properties of the crosslinked multilayers were investigated by surface plasmon resonance spectroscopy. The marine antifouling and fouling-release properties were tested against the settlement of zoospores of the green alga Ulva linza and the subsequent development and removal of sporelings. With spin coating and thermal crosslinking, a thick yet homogeneous coating was obtained with antifouling properties against marine algal zoospores indicating the potential of these compounds for application in protective coatings.

Surface Modification by Polyzwitterions of the Sulfabetaine-Type, and Their Resistance to Biofouling.

Films of zwitterionic polymers are increasingly explored for conferring fouling resistance to materials. Yet, the structural diversity of polyzwitterions is rather limited so far, and clear structure-property relationships are missing. Therefore, we synthesized a series of new polyzwitterions combining ammonium and sulfate groups in their betaine moieties, so-called poly(sulfabetaine)s. Their chemical structures were varied systematically, the monomers carrying methacrylate, methacrylamide, or styrene moieties as polymerizable groups. High molar mass homopolymers were obtained by free radical polymerization. Although their solubilities in most solvents were very low, brine and lower fluorinated alcohols were effective solvents in most cases. A set of sulfabetaine copolymers containing about 1 mol % (based on the repeat units) of reactive benzophenone methacrylate was prepared, spin-coated onto solid substrates, and photo-cured. The resistance of these films against the nonspecific adsorption by two model proteins (bovine serum albumin-BSA, fibrinogen) was explored, and directly compared with a set of references. The various polyzwitterions reduced protein adsorption strongly compared to films of poly(nbutyl methacrylate) that were used as a negative control. The poly(sulfabetaine)s showed generally even somewhat higher anti-fouling activity than their poly(sulfobetaine) analogues, though detailed efficacies depended on the individual polymer-protein pairs. Best samples approach the excellent performance of a poly(oligo(ethylene oxide) methacrylate) reference.

Microfluidic Shear Force Assay to Determine Cell Adhesion Forces.

Cell adhesion is implicated in many physiological settings such as the retention of hematopoietic stem cells (HSCs) in their bone marrow niches or their migration into the bloodstream. During HSC mobilization these adhesion sites are cleaved and have to be newly formed during HSC homing and engraftment. To determine the adhesive properties of HSCs on different extracellular matrix (ECM) molecules, we present a microfluidic shear force assay, where a laminar flow is used to detach a semi-adherent cell population, the HSC model cell line KG-1a, from an ECM protein-coated substrate. This technique combines the high throughput of population-based assays with the ability to observe cell detachment in real time. Additionally, it is suitable for weakly adherent cells, as the setup allows cell incubation on various substrates and application of shear stress ranging several orders of magnitude in one setup without additional washing or transfer steps. As a measure for the adhesion strength of the studied cell population on the substrate, the critical shear force τ50 is determined which is required to remove 50% of the initially adherent cell fraction.

Sediment challenge to promising ultra-low fouling hydrophilic surfaces in the marine environment.

Hydrophilic coatings exhibit ultra-low fouling properties in numerous laboratory experiments. In stark contrast, the antifouling effect of such coatings in vitro failed when performing field tests in the marine environment. The fouling release performance of nonionic and zwitterionic hydrophilic polymers was substantially reduced compared to the controlled laboratory environment. Microscopy and spectroscopy revealed that a large proportion of the accumulated material in field tests contains inorganic compounds and diatomaceous soil. Diatoms adhered to the accumulated material on the coating, but not to the pristine polymer. Simulating field tests in the laboratory using sediment samples collected from the test sites showed that incorporated sand and diatomaceous earth impairs the fouling release characteristics of the coatings. When exposed to marine sediment from multiple locations, particulate matter accumulated on these coatings and served as attachment points for diatom adhesion and enhanced fouling. Future developments of hydrophilic coatings should consider accumulated sediment and its potential impact on the antifouling performance.

Low-Fouling Thin Hydrogel Coatings Made of Photo-Cross-Linked Polyzwitterions.

Although zwitterionic chemistries are among the most promising materials for producing nonfouling surfaces, their structural diversity has been low until now. Here, we compare the in vitro fouling behavior of a set of four systematically varied sulfa-/sulfobetaine-containing zwitterionic hydrogel coatings against a series of proteins and nonmotile as well as motile marine organisms as model foulers. The coatings are prepared by simultaneous photoinduced cross-linking and surface anchoring to elucidate the effect of the molecular structure of the zwitterionic moieties on their antifouling activity. Analogously prepared coatings of poly(butyl methacrylate) and poly(oligoethylene glycol methacrylate) serve as references. Photoreactive polymers are synthesized by the statistical copolymerization of sulfobetaine or sulfabetaine methacrylates and methacrylamides with a benzophenone derivative of 2-hydroxyethyl methacrylate and are applied as a thin film coating. While keeping the density of the zwitterionic and cross-linker groups constant, the molecular structure of the zwitterionic side chains is varied systematically, as is the arrangement of the ion pairs in the side chain by changing the classical linear geometry to a novel Y-shaped geometry. All of the polyzwitterions strongly reduce fouling compared to poly(butyl methacrylate). Overall, the sulfabetaine polyzwitterion coatings studied matches the high antifouling effectiveness of oligo(ethylene glycol)-based ones used as a control. Nevertheless, performances varied individually for a given pair of polymer and fouler. The case of the polysulfobetaines exemplifies that minor chemical changes in the polymer structure affect the antifouling performance markedly. Accordingly, the antifouling performance of such polymers cannot be correlated simply to the type of zwitterion used (which could be generally ranked as better performing or poorer performing) but is a result of the polymer's precise chemical structure. Our findings underline the need to enlarge the existing structural diversity of polyzwitterions for antifouling purposes to optimize the potential of their chemical structure.

Fouling-Release Properties of Dendritic Polyglycerols against Marine Diatoms.

Dendritic polyglycerols (PGs) were grafted onto surfaces using a ring-opening polymerization reaction, and the fouling-release properties against marine organisms were determined. The coatings were characterized by spectroscopic ellipsometry, contact angle goniometry, ATR-FTIR, and stability tests in different aqueous media. A high resistance toward the attachment of different proteins was found. The PG coatings with three different thicknesses were tested in a laboratory assay against the diatom Navicula incerta and in a field assay using a rotating disk. Under static conditions, the PG coatings did not inhibit the initial attachment of diatoms, but up to 94% of attached diatoms could be removed from the coatings after exposure to a shear stress of 19 Pa. Fouling release was found to be enhanced if the coatings were sufficiently thick. The excellent fouling-release properties were supported in dynamic field-immersion experiments in which the samples were continually exposed to a shear stress of 0.18 Pa.

Dynamic field testing of coating chemistry candidates by a rotating disk system.

Quick and reliable testing is crucial for the development of new fouling release (FR) coatings. Exposure of these coatings to natural multispecies communities is essential in evaluating their efficacy. To this end, we present a rotating disk setup for dynamic field exposure. To achieve a well-defined flow on the surface of the disk, an easy to use sample mounting system was developed that provides a smooth and even surface. We related the angular velocity of the disk to the wall shear stress on the surface with a hydrodynamic model. The wall shear stress was adjusted to values previously found to be suitable to discriminate dynamic diatom attachment on different coating chemistries in the lab. The effect of the dynamic conditions was shown by comparing polystyrene slides under static and dynamic exposure. Using a set of self-assembled monolayers, the discrimination potential of the assay in a multispecies environment was demonstrated.