Functionalization of ZnAl-Layered Double Hydroxide with Ensulizole and Its Application as a UV-Protective Agent in a Transparent Polymer Coating.

In this study, we propose a promising photoprotective additive that combines the advantages of both organic UV absorbers and inorganic particles without compromising the properties of the paint material. This additive involves the intercalation of a well-known organic UV absorber, 2-phenylbenzimidazole-5-sulfonic acid (PBISA), into zinc-aluminum layered double hydroxide (ZnAl-LDH). Three ZnAl-LDH intercalates with PBISA were prepared using various methods based on either anion exchange or direct synthesis. The intercalates were characterized using powder X-ray diffraction, thermogravimetry, elemental analysis, and IR and UV-Vis spectroscopies. The composition and basal spacings of all three intercalates are very similar. An effective UV protection film was prepared when the ZnAl-PBISA-1 intercalate was incorporated into polyurethane-acrylate lacquer. The resultant UV protective film exhibited stability and uniform distribution of the intercalated fillers. Some minimal particle sedimentation and aggregation were observed on the cured film's underside, but did not compromise the films' UV protective properties. The prepared lacquers with intercalated fillers offer a viable solution for the surface modification of plastic products.

Synthesis and Exfoliation of Calcium Organophosphonates for Tailoring Rheological Properties of Sodium Alginate Solutions: A Path toward Polysaccharide-Based Bioink.

Layered nanoparticles with surface charge are explored as rheological modifiers for extrudable materials, utilizing their ability to induce electrostatic repulsion and create a house-of-cards structure. These nanoparticles provide mechanical support to the polymer matrix, resulting in increased viscosity and storage modulus. Moreover, their advantageous aspect ratio allows for shear-induced orientation and decreased viscosity during flow. In this work, we present a synthesis and liquid-based exfoliation procedure of phenylphosphonate-phosphate particles with enhanced ability to be intercalated by hydrophilic polymers. These layered nanoparticles are then tested as rheological modifiers of sodium alginate. The effective rheological modification is proved as the viscosity increases from 101 up to 103 Pa·s in steady state. Also, shear-thinning behavior is observed. The resulting nanocomposite hydrogels show potential as an extrudable bioink for 3D printing in tissue engineering and other biomedical applications, with good shape fidelity, nontoxicity, and satisfactory cell viability confirmed through encapsulation and printing of mouse fibroblasts.

Evaluating the Use of TiO2 Nanoparticles for Toxicity Testing in Pulmonary A549 Cells.

Purpose: Titanium dioxide nanoparticles, 25 nm in size of crystallites (TiO2 P25), are among the most produced nanomaterials worldwide. The broad use of TiO2 P25 in material science has implied a request to evaluate their biological effects, especially in the lungs. Hence, the pulmonary A549 cell line has been used to estimate the effects of TiO2 P25. However, the reports have provided dissimilar results on caused toxicity. Surprisingly, the physicochemical factors influencing TiO2 P25 action in biological models have not been evaluated in most reports. Thus, the objective of the present study is to characterize the preparation of TiO2 P25 for biological testing in A549 cells and to evaluate their biological effects. Methods: We determined the size and crystallinity of TiO2 P25. We used four techniques for TiO2 P25 dispersion. We estimated the colloid stability of TiO2 P25 in distilled water, isotonic NaCl solution, and cell culture medium. We applied the optimal dispersion conditions for testing the biological effects of TiO2 P25 (0-100 µg.mL-1) in A549 cells using biochemical assays (dehydrogenase activity, glutathione levels) and microscopy. Results: We found that the use of fetal bovine serum in culture medium is essential to maintain sufficient colloid stability of dispersed TiO2 P25. Under these conditions, TiO2 P25 were unable to induce a significant impairment of A549 cells according to the results of biochemical and microscopy evaluations. When the defined parameters for the use of TiO2 P25 in A549 cells were met, similar results on the biological effects of TiO2 P25 were obtained in two independent cell laboratories. Conclusion: We optimized the experimental conditions of TiO2 P25 preparation for toxicity testing in A549 cells. The results presented here on TiO2 P25-induced cellular effects are reproducible. Therefore, our results can be helpful for other researchers using TiO2 P25 as a reference material.

Insight into the Lubrication and Adhesion Properties of Hyaluronan for Ocular Drug Delivery.

Hyaluronan (HA) is widely used for eye drops as lubricant to counteract dry eye disease. High and low molecular weight HA are currently used in ophthalmology. However, a large portion of the current literature on friction and lubrication addresses articular (joint) cartilage. Therefore, eye drops compositions based on HA and its derivatized forms are extensively characterized providing data on the tribological and mucoadhesive properties. The physiochemical properties are investigated in buffers used commonly in eye drops formulations. The tribological investigation reveals that amphiphilic HA-C12 decreases the friction coefficient. At the same time, the combination of trehalose/HA or HAC12 enhances up to eighty-fold the mucoadhesiveness. Thus, it is predicted a prolonged residence time on the surface of the eye. The incorporation of trehalose enhances the protection of human keratinocytes (HaCaT) cells, as demonstrated in an in-vitro cell-desiccation model. The presence of trehalose increases the friction coefficient. Medium molecular weight HA shows significantly lower friction coefficient than high molecular weight HA. This research represents a first, wide array of features of diverse HA forms for eye drops contributing to increase the knowledge of these preparations. The results here presented also provide valuable information for the design of highly performing HA-formulations addressing specific needs before preclinic.

Oleate-modified hyaluronan: Controlling the number and distribution of side chains by varying the reaction conditions.

In this work, low molecular weight hyaluronan was chemically modified by oleoyl moieties utilising mixed anhydrides methodology. The activation of oleic acid with benzoyl chloride in organic solvents miscible with water was followed by NMR spectroscopy. The product selectivity correlates with the solvent's Hildebrand solubility parameter. Furthermore, the effect of the solvent for the mixed anhydride formation was elucidated by density functional theory (DFT) and showed that the reactions are faster in acetonitrile or alcohols than in hexane. Furthermore, the solvent demonstrated to control the substituent distribution pattern along HA chain during esterification. An even distribution of substituents was observed in reactions performed in water mixed with ethers. The substituent distribution pattern clearly influenced the aggregation behaviour of amphiphilic HA, controlling the stability of the delivery system, while increasing the encapsulation capacity.

Formulation of hyaluronan grafted with dodecanoic acid as a potential ophthalmic treatment.

This work concerns the chemical modification of medium molecular weight hyaluronan for ophthalmic applications. The synthesis of amphiphilic HA with dodecanoyl moities was carried out under mild aqueous conditions. Perfect control of the degree of substitution was obtained by varying the molar ratio of activated fatty acid used in the reaction feed. Moreover, the preparation of the derivatives was optimized to achieve the desired degree of substitution (DS = 9.0 ± 0.2 %). The prepared hyaluronan derivatives were water-soluble and exhibited self-associating properties (amphiphilicity). The structure of the prepared derivatives was elucidated by NMR spectroscopy, rheology, turbidity, SEC-MALLS, and gas chromatography (GC). The hydrophobic moieties increase the solution viscosity by physical crosslinking. Low concentration of HAC12 is needed to prepare highly viscous solutions with potential use for ophthalmic applications. Amphiphilic HA kept the biocompatibility of hyaluronan. The degree of substitution and Mw of the amphiphilic HA controls the sterilization by filtration. The protection against desiccation was tested using human keratinocytes (HaCaT) cells lines.

Retinoic acid grafted to hyaluronan for skin delivery: Synthesis, stability studies, and biological evaluation.

All-trans retinoic acid (ATRA) was grafted to hyaluronan (HA) via esterification. The reaction was mediated by mixed anhydrides. A perfect control of the degree of substitution (0.5-7.5%) was obtained by varying the molar ratio of retinoic acid in the feed. The degree of substitution plays a significant role in the long-term stability. The photodegradation of HA-ATRA upon UVA irradiation resulted in ß-ionone, ß-cyclocitral and 5,6-epoxy-(E)-retinoic acid. The photostability of the conjugate had increased with the combination with morin. The chemical structure of HA-ATRA and its degradation products was elucidated using NMR spectroscopy, SEC-MALLS, and gas chromatography-mass spectrometry (GC-MS). ATRA did not loss its biological activity after conjugation, as demonstrated by gene expression. The derivative was able to penetrate across the stratum corneum. Besides, HA-ATRA downregulated the expression of anti-inflammatory interleukins 6 and 8. HA-ATRA would be expected to be used for transdermal drug delivery or cosmetics.

Exfoliation of layered mixed zirconium 4-sulfophenylphosphonate phenylphosphonates.

Mixed zirconium 4-sulfophenylphosphonate phenylphosphonates with formulae Zr(HO3SC6H4PO3)1.8(C6H5PO3)0.2·2.6H2O, Zr(HO3SC6H4PO3)1.3(C6H5PO3)0.7·2H2O, and Zr(HO3SC6H4PO3)0.7(C6H5PO3)1.3·3.6H2O (generally, ZrSPhP) were intercalated with a series of amino alcohols, H2N(CH2)nOH, where n = 2 to 6, and triethylamine. It was found that in the case of amino alcohols the basal spacing of the intercalates increases linearly with n. The intercalates prepared can be exfoliated either by sonication or by the action of high-shear forces. The use of a high-shear force disperser is a more efficient exfoliation method, as it provides lamellas with larger lateral dimensions in a much shorter time. It was found that amino alcohols provide roughly the same results regardless of the length of their carbon chain. As follows from atomic force microscopy measurements, triethylamine is the most appropriate exfoliation agent for ZrSPhP as it produces platelets with the largest lateral size and the lowest amount of defects.

Synthesis and Physicochemical Characterization of Undecylenic Acid Grafted to Hyaluronan for Encapsulation of Antioxidants and Chemical Crosslinking.

In this work, a new amphiphilic derivative made of 10-undecylenic acid grafted to hyaluronan was prepared by mixed anhydrides. The reaction conditions were optimized, and the effect of the molecular weight (Mw), reaction time, and the molar ratio of reagents was explored. Using this methodology, a degree of substitution up to 50% can be obtained. The viscosity of the conjugate can be controlled by varying the substitution degree. The physicochemical characterization of the modified hyaluronan was performed by infrared spectroscopy, Nuclear Magnetic Resonance, Size-Exclusion Chromatography combined with Multiangle Laser Light Scattering (SEC-MALLS), and rheology. The low proton motility and self-aggregation of the amphiphilic conjugate produced overestimation of the degree of substitution. Thus, a novel method using proton NMR was developed. Encapsulation of model hydrophobic guest molecules, coenzyme Q10, curcumin, and α-tocopherol into the micellar core was also investigated by solvent evaporation. HA-UDA amphiphiles were also shown to self-assemble into spherical nanostructures (about 300 nm) in water as established by dynamic light scattering. Furthermore, HA-UDA was crosslinked via radical polymerization mediated by ammonium persulphate (APS/TEMED). The cross-linking was also tested by photo-polymerization catalyzed by Irgacure 2959. The presence of the hydrophobic moiety decreases the swelling degree of the prepared hydrogels compared to methacrylated-HA. Here, we report a novel hybrid hyaluronan (HA) hydrogel system of physically encapsulated active compounds and chemical crosslinking for potential applications in drug delivery.

Layered calcium phenylphosphonate: a hybrid material for a new generation of nanofillers.

The use of nanosheets of layered calcium phenylphosphonate as a filler in a polymeric matrix was investigated. Layered calcium phenylphosphonate (CaPhP), with chemical formula CaC6H5PO3∙2H2O, is a hybrid organic-inorganic material that exhibits a hydrophobic character due to the presence of phenyl groups on the surface of the layers. In this paper, various CaPhP synthesis methods were studied with the aim of obtaining a product most suitable for its subsequent exfoliation. The liquid-based approach was used for the exfoliation. It was found that the most promising technique for the exfoliation of CaPhP in an amount sufficient for incorporation into polymers involved using propan-2-ol with a strong shear force generated in a high-shear disperser. The filler was tested both in its unexfoliated and exfoliated forms for the preparation of polymer composites, for which a low molecular weight epoxy resin based on bisphenol A was used as a polymer matrix. The prepared samples were characterized by powder X-ray diffraction, atomic force microscopy, optical and scanning electron microscopy, and dynamic mechanical analysis. Flammability and gas permeation tests were also performed. The addition of the nanofiller was found to influence the composite properties - the exfoliated particles were found to have a higher impact on the properties of the prepared composites than the unexfoliated particles of the same loading.

Grafting of steroids to hyaluronan towards the design of delivery systems for antioxidants: The role of hydrophobic core.

In this work, amphiphilic hyaluronic acid (HA) was synthesized by the chemical bonding of steroids. Particularly, succinyl cholesterol (SCH), cholic acid (CA), deoxycholic acid (DOCA), and 18ß-glycyrrhetinic acid (GA) were activated by benzoyl chloride towards the esterification reaction of HA in water. The degree of substitution can be controlled by varying the feed ratio of mixed anhydride to HA and up to 25% (mol/mol) can be obtained. Due to mild reaction conditions, no degradation of the polysaccharide was observed. The prepared amphiphilic polymers were characterized by NMR, infrared spectroscopy (FT-IR) and SEC/MALLS, as well as turbidity and size of the aggregates. The developed system is proposed for the delivery of hydrophobic drugs; for this purpose, curcumin, vitamin E and coenzyme Q10 were used as hydrophobic models; these molecules were loaded into the conjugates with high efficiency. The loading capacity was a function of degree of substitution. Furthermore, the biocompatibility of the derivatives and the cellular uptake of the delivery system enabled us to demonstrate the potential of the prepared delivery systems.

Synthesis of graft copolymers based on hyaluronan and poly(3-hydroxyalkanoates).

This work reports the synthesis and characterisation of new amphiphilic hyaluronan (HA) grafted with poly(3-hydroxyalkanoates) (PHAs) conjugates. Hydrolytic depolymerisation of PHAs was used for the synthesis of defined oligo(3-hydroxyalkanoates)-containing carboxylic terminal moieties. A kinetic study of the depolymerisation was followed to prepare oligomers of required molecular weight. PHAs were coupled with hydroxyl groups of HA mediated by N, N'-carbonyldiimidazole (CDI) or HSTU Tetramethyl-O-(N-succinimidyl) uronium hexafluorophosphate. For the first time, the covalent bonding of oligo derivatives of P(3-hydroxybutyrate), P(3-hydroxyoctanoate), P(3-hydroxyoctanoate-co-3-hydroxydecanoate) and P(3-hydroxyoctanoate-co-3-hydroxydecanoate-co-3-hydroxydodecanoate) and HA was achieved by "grafting to" strategy. Achieved grafting degree was a function of hydrophobicity of PHA, Mw and polarity of the solvent. The most suitable reaction conditions were observed for oligo (3-hydroxybutyrate) grafted to HA (grafting degree of 14%). Graft copolymers were characterized by FT-IR, NMR, DSC and SEC-MALLS. Graft copolymers can be physically loaded with hydrophobic drugs and may serve as drug delivery system.

Slow to fast muscle transformation following heterochronous isotransplantation is influenced by host thyroid hormone status.

We studied the effect of regeneration, altered innervation and thyroid hormone (TH) levels on fiber type transitions in slow soleus (SOL) muscles grafted (GRAFT) into host extensor digitorum longus (EDLh) muscles of euthyroid (EU), hyperthyroid (HT) and hypothyroid (HY) Lewis strain rats. SOL muscles were excised from 3-week to 4-week-old inbred Lewis rats and intramuscularly transplanted into EDLh muscles of 2-month-old female rats of the same strain. The proportions of type 1, 2A, 2X and 2B fibers of GRAFT were determined by immunohistochemistry and compared with those of EDLh muscle and EDL and SOL muscles of the unoperated contralateral hind limb. After an average regeneration period of 6-7 months and after being reinnervated by the "fast" peroneal nerve of EDLh muscle, GRAFT was transformed into a fast muscle. However, the extent of GRAFT transformation varied with different TH states. In the EU rats, GRAFT contained about 95 % of fast fibers, among which type 2X and 2B fibers predominated (about 75 %). The transition toward fast muscle phenotype was more pronounced in HT status, where the fastest type 2B fibers predominated. On the contrary, in HY status, the slow to fast transformation was less pronounced, as GRAFT contained less type 2B and 2X but more type 2A and 1 fibers. We conclude that the type of innervation is the crucial factor for the slow to fast fiber type transitions in GRAFT, but the extent of muscle transformation is further modulated by altered TH status.

The Electroosmotic Flow (EOF).

Controlling and manipulating liquids and analytes at the sub-millimeter scale is a challenge that frequently requires new methods to be developed. Indeed, scaling-down of traditional macroscopic ideas often fails. For instance, pumping liquids using pressure differences is often impractical and counterproductive because the resulting parabolic flow profile deforms sample zones. As the size of the system shrinks, the surface-to-volume ratio increases and interfacial effects become dominant. This actually opens new possibilities since the phenomenon of electroosmotic flow (EOF), wherein a fluid is made to move relative to a stationary charged boundary, can then be exploited to design efficient microfluidic devices. In this chapter, we review the fundamental principles of EOF as well as some of the methods used to coat channel walls and reduce the impact of EOF in situations where it would be unfavorable for the device performance.

Capillary electrophoresis sequencing of small ssDNA molecules versus the Ogston regime: fitting data and interpreting parameters.

We study the mobility of short ssDNA fragments (approximately 30-500 bases) separated by capillary electrophoresis in entangled polymer solutions. Although this corresponds to what is commonly called the Ogston regime, the corresponding sieving concept has never been defined properly nor tested quantitatively. We consider three formulas that have been suggested to fit data in this range of ssDNA sizes, and we discuss how their free parameters are related to actual physical parameters. We test these formulas with new data obtained in our laboratory using a commercial poly-N,N-dimethylacrylamide sieving matrix. Our results show that all three formulas provide decent fits. However, the traditional Ogston equation produces fitting parameters that appear to lack physical meaning. Surprisingly, all three approaches predict that the effective pore size and fiber radius are almost equal. This is the first step towards the development of a systematic approach to optimizing sequencing systems for this size range.