ABSTRACT
Additive manufacturing has garnered significant interest in various industries due to its flexibility and capability to produce parts with complex shapes. However, issues related to surface quality, such as roughness and microstructural defects, necessitate the use of post-processing techniques to achieve the desired properties. Ti6Al4V alloy, produced additively, was finished using low-energy discharges, and the new surface integrity properties resulting from the induced heat energy were investigated. To further understand the influence of discharge energy on the formation of the new layer, roughness parameters and power spectral density were used to characterize the surface topography. SEM and EDS analyses were performed to examine the morphology and microstructural defects such as microcracks. The results indicate that the heat energy induced by the discharge improved the properties of the surface. SEM analysis revealed that the new layer was characterized by a reduction in defects such as unmelted particles, the balling effect, and microcracks. At the lowest investigated discharge energy of E = 0.21 mJ, surface roughness, Sa, was reduced by about 69%, which is equal to about 2 µm, accompanied by a significant decrease in microcracks. EDS analysis indicated that the diffusion of copper and zinc from the electrode to the top surface was related to the discharge energy. Furthermore, prediction models of the influence of wire electrical discharge polishing parameters, including discharge energy, wire speed, and time interval, on the surface roughness and material removal rate (MRR) were developed using the response surface methodology.
ABSTRACT
Finishing operations are one of the most challenging tasks during a manufacturing process, and are responsible for achieving dimensional accuracy of the manufactured parts and the desired surface topography properties. One of the most advanced finishing technologies is grinding. However, typical grinding processes have limitations in the acquired surface topography properties, especially in finishing difficult to cut materials such as Inconel 625. To overcome this limitation, a new type of grinding wheel is proposed. The tool is made up of grains of different sizes, which results in less damage to the work surface and an enhancement in the manufacturing process. In this article, the results of an experimental study of the surface grinding process of Inconel 625 with single-granular and multi-granular wheels are presented. The influence of various input parameters on the roughness parameter (Sa) and surface topography was investigated. Statistical models of the grinding process were developed based on our research. Studies showed that with an increase in the cutting speed, the surface roughness values of the machined samples decreased (Sa = 0.9 µm for a Vc of 33 m/s for a multigranular wheel). Observation of the grinding process showed an unfavorable effect of a low grinding wheel speed on the machined surface. For both conventional and multigranular wheels, the highest value for the Sa parameter was obtained for Vc = 13 m/s. Regarding the surface topography, the observed surfaces did not show defects over large areas in the cases of both wheels. However, a smaller portion of single traces of active abrasive grains was observed in the case of the multi-granular wheel, indicating that this tool performs better finishing operations.
ABSTRACT
The industrial application of electrical discharge machining (EDM) for manufacturing injection molding, in many cases, requires forming depth cavities with high length-to-width ratios, which is quite challenging. During slot EDM with thin-walled electrodes, short-circuits and arcing discharges occur, as a result of low efficiency in removing debris and bubble gas from the gap. Furthermore, unstable discharges can cause increases in tool wear and shape deviation of the machined parts. In order to characterize the influence of the type of electrode material and EDM parameters on the deep slot machining of high-thermal-conductivity tool steel (HTCS), experimental studies were conducted. An analytical and experimental investigation is carried out on the influence of EDM parameters on discharge current and pulse-on-time on the tool wear (TW), surface roughness (Ra), slot width (S)-dimension of the cavity, and material removal rate (MRR). The analyses of the EDS spectrum of the electrode indicate the occurrence of the additional carbon layer on the electrode. Carbon deposition on the anode surface can provide an additional thermal barrier that reduces electrode wear in the case of the copper electrode but for graphite electrodes, uneven deposition of carbon on the electrode leads to unstable discharges and leads to increase tool wear. The response surface methodology (RSM) was used to build empirical models of the influence of the discharge current I and pulse-on-time ton on Ra, S, TW, and MRR. Analysis of variance (ANOVA) was used to establish the statistical significance parameters. The calculated contribution indicated that the discharge current had the most influence (over 70%) on the Ra, S, TW, and MRR, followed by the discharge time. Multicriteria optimization with Derringer's function was then used to minimize the surface roughness, slot width, and TW, while maximizing MRR. A validation test confirms that the maximal error between the predicted and obtained values did not exceed 7%.