Influence of Different Deep Eutectic Solvents and Plant Extracts on Antioxidant, Mechanical, and Color Properties of Alginate Film.

Eco-friendly functional alginate films with plant extracts (chokeberry pomace (ChP) or lemon balm (LB) herb) were obtained. Moreover, deep eutectic solvents (DESs) based on choline chloride, glucose, and betaine were used to acquire the active substances from plant materials. The films were tested regarding the antioxidant, mechanical, and color properties. The results revealed that the films' antioxidant capacities (AC) depended on the extract type and DES used, namely AC values for alginate films with LB were higher than those with ChP. Moreover, the results of the films' mechanical properties depended only on the DES, which acted as a plasticizer in most cases. Furthermore, the color analysis of the studied films showed a dependence on the type of extract and DES. The lightness (L*) was influenced only by the DES type, while the solvent and extract type affected the a* and b* values. Our results show that the films can be applied as active packaging for food products.

Alginate Films Enriched in Raspberry and/or Black Currant Seed Oils as Active Food Packaging.

Alginate films plasticized with glycerol and enriched in raspberry and/or black currant seed oils were prepared via casting solution techniques. The intention was to create active films for food packaging where antioxidants in a film would deactivate oxidants in a packed product or its surroundings, improving conditions inside packaging and extending the shelf life of such a product. The prepared materials were characterized by physicochemical, spectroscopic, mechanical, water vapor transmission (WVTR), and antioxidant activity analysis. Infrared spectra of the alginate films with oils were similar to those without the additive; the band with a maximum at about 1740 cm-1 stood out. The prepared materials with oils were thicker, contained less water, were more yellow, and were less permeable to water vapor. Moreover, the presence of the oil in the films resulted in a slightly lower Young's modulus and lower stress at break values but higher strain at break. The antioxidant capacity of raspberry seed oil itself was about five times higher than that of black currant seed oil, and a similar trend was noticed for films modified with these oils. The results indicated that both oils could be used as active substances with antioxidant properties in food packaging.

Stability Studies, Biodegradation Tests, and Mechanical Properties of Sodium Alginate and Gellan Gum Beads Containing Surfactant.

The excessive presence of single-use plastics is rapidly degrading our natural environment on a global scale due to their inherent resistance to decomposition. Wet wipes used for personal or household purposes contribute significantly to the accumulation of plastic waste. One potential solution to address this problem involves developing eco-friendly materials that possess the ability to degrade naturally while retaining their washing capabilities. For this purpose, the beads from sodium alginate, gellan gum, and a mixture of these natural polymers containing surfactant were produced using the ionotropic gelation method. Stability studies of the beads by observing their appearance and diameter were performed after incubation in solutions of different pH values. The images showed that macroparticles were reduced in size in an acidic medium and swelled in solution of pH-neutral phosphate-buffered saline. Moreover, all the beads first swelled and then degraded in alkaline conditions. The beads based on gellan gum and combining both polymers were the least sensitive to pH changes. The compression tests revealed that the stiffness of all macroparticles decreased with the increasing pH of the solutions in which they were immersed. The studied beads were more rigid in an acidic solution than in alkaline conditions. The biodegradation of macroparticles was assessed using a respirometric method in soil and seawater. It is important to note that the macroparticles degraded more rapidly in soil than in seawater.

Physicochemical and Antibacterial Properties of Alginate Films Containing Tansy (Tanacetum vulgare L.) Essential Oil.

Tansy (Tanacetum vulgare) is a common plant used in folk medicine for digestive problems, fevers, and migraines; against parasites; and as an insect repellent. The active substances in essential oil are responsible for its antimicrobial and antioxidant activity. Thus, tansy essential oil (TO) was added to alginate films to fabricate materials with antioxidant and antibacterial properties for food packaging. Sodium alginate films with glycerol and TO were tested in terms of structure, mechanical, thermal, antioxidant, and antibacterial properties. The structure of the films was examined using SEM and an ATR-FTIR spectrophotometer. The addition of TO to the alginate film significantly changed the films' microstructure, making them rougher and porous. A low-intensity band at 1739 cm-1, indicative of the presence of TO, appeared in all spectra of alginate films with TO. Moreover, the studies revealed that essential oil acted as a plasticizer, slightly reducing tensile strength from about 7 MPa to 5 MPa and increasing elongation at break from 52% to 56% for the sample with 2% TO. The alginate films enriched in TO exhibited antioxidant properties (280 µmol Trolox/100 g of the sample with 2% TO) and antibacterial activity against Escherichia coli, Staphylococcus aureus, and Pseudomonas aeruginosa.

Bionanocellulose/Poly(Vinyl Alcohol) Composites Produced by In-Situ Method and Ex-Situ/Impregnation or Sterilization Methods.

The purpose of the work was to obtain composites based on bionanocellulose (BNC) and poly(vinyl alcohol) (PVA) for specific biomedical and cosmetic applications and to determine how the method and conditions of their preparation affect their utility properties. Three different ways of manufacturing these composites (in-situ method and ex-situ methods combined with sterilization or impregnation) were presented. The structure and morphology of BNC/PVA composites were studied by ATR-FTIR spectroscopy and scanning microscopy (SEM, AFM). Surface properties were tested by contact angle measurements. The degree of crystallinity of the BNC fibrils was determined by means of the XRD method. The mechanical properties of the BNC/PVA films were examined using tensile tests and via the determination of their bursting strength. The water uptake of the obtained materials was determined through the gravimetric method. The results showed that PVA added to the nutrient medium caused an increase in biosynthesis yield. Moreover, an increase in base weight was observed in composites of all types due to the presence of PVA. The ex-situ composites revealed excellent water absorption capacity. The in-situ composites appeared to be the most durable and elastic materials.

Freeze-Dried Matrices Composed of Degradable Polymers with Surfactant-Loaded Microparticles Based on Pectin and Sodium Alginate.

Gelatin/polyvinylpyrrolidone/hydroxyethyl cellulose/glycerol porous matrices with microspheres made of sodium alginate or pectin and sodium alginate were produced. A surfactant was loaded into these microparticles. The microspheres were characterized using optical microscopy, scanning electron microscopy SEM, and laser diffraction particle size analyzer. For the matrices, the density, porosity, swelling capacity, dissolution in phosphate saline buffer were determined and SEM, mechanical, and thermogravimetric studies were applied. The results showed that the size of the two-component microspheres was slightly larger than that of single-ingredient microparticles. The images confirmed the spherical shape of the microparticles. The prepared matrices had high water uptake ability and porosity due to the presence of hydrophilic polymers. The presence of microparticles in the matrices caused a decrease in these parameters. Degradation of the composites with the microspheres was significantly faster than the matrix without them. The addition of microparticles increased the stiffness and toughness of the prepared materials. The efficiency of the thermal decomposition main stage was reduced in the samples with microspheres, whereas a char residue increased in these composites.

Corona Charging of Isotactic-Polypropylene Composites.

A new approach to obtaining piezoelectric polymeric films based on the isotactic-polypropylene (i-PP) using corona discharge with the energy of 45 W·min/m2 was presented. Detailed analyses with Atomic Force Microscopy (AFM) led to the conclusion that the surface quality was the important factor influencing the possibility of charging the i-PP composites, which was necessary to induce the permanent piezoelectric effect. It has been found that the high surface smoothness of the polymer films contributed to improved piezoelectric properties without the need for an additional polymer modification such as orientation, foaming or doping with fillers. The values of the piezoelectric constant, d33, of the studied samples were compared to these values for the analogous systems polarized with a constant electric field of 100 V/µm. The milder conditions of the film polarization during the corona discharge process are sufficient to achieve the electrets in i-PP films. The simple and cheap method proposed can be profitable in obtaining flexible electrets in the form of thin films for the production of personal biomedical sensors.

Physico-Chemical and Light-Induced Properties of Quinoline Azo-dyes Polymers.

We present investigation of optical and photochromic properties as well as of surface quality of thin films of novel methacrylic polymers with 8-hydroxyquinoline azo-dyes in side-chain. Additionally, thermal stability of polymer powders was examined and their glass transition temperature was determined. Optical properties (extinction coefficient and refractive index) were determined by spectroscopic ellipsometry (SE) combined with absorbance measurements. Photoresponsive behavior was investigated by determination of photoisomerization rates under irradiation with unpolarized 365 nm light, as well as by conduction of holographic grating inscription experiment. Thin film quality was determined by atomic force microscopy (AFM) measurements. Thermal analysis was performed by thermogravimetric (TG), derivative thermogravimetric (DTG) and differential scanning calorimetry (DSC) measurements. We found that optical properties as well as photoisomerization rates of investigated polymers are dependent on the substituent in the para position of the phenyl ring. Surface relief grating inscription was successfully generated only for materials with chromophores containing dimethylamino (N(CH3)2) and methyl (CH3) substituents, but all materials exhibited birefringence grating in the bulk. Surface of most thin films was very smooth, but its quality was impaired by neutral (H) as well as carboxyl (COOH) substituent. Thermal stability of copolymers with side-chain chromophores was improved compared to pure poly(methyl methacrylate) (PMMA).

Effect of plasticizer and surfactant on the properties of poly(vinyl alcohol)/chitosan films.

The objective of this study was to develop eco-friendly films based on poly(vinyl alcohol) (PVA) and chitosan (CTS) with the addition of plasticizer (glycerol or sorbitol) and surfactant (cocamidopropyl betaine). The properties of the obtained polymeric films were determined by contact angle measurements, attenuated total reflection infrared spectroscopy (ATR-FTIR), atomic force microscopy (AFM), mechanical tests, and moisture content analysis. The results indicated that four-component blends had high surface hydrophilicity and surface roughness due to the presence of the surfactant. Glycerol incorporation into PVA/CTS blends resulted in higher flexibility and greater water absorption capacity of the three- and four-component polymeric blends compared with these blends with sorbitol. By contrast, the addition of the surfactant to the materials is essential for their application in personal hygiene products as disposable wipes.

Surface Studies of UV Irradiated Polypropylene Films Modified with Mineral Fillers Designed as Piezoelectric Materials.

Isotactic-polypropylene (i-PP) films with inorganic minerals such as Sillikolloid, perlite, or glass beads were prepared. The obtained polymeric films were subjected to an orientation process. Moreover, this paper includes results how the artificial accelerated weathering influences surface properties of the unoriented and oriented i-PP films with the mineral fillers. Changes in the ultraviolet (UV) treated polymeric films were studied with attenuated total reflectance-Fourier transform infrared spectroscopy (ATR-FTIR), X-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM), and by measuring contact angles. The results revealed that photooxidation of i-PP was more effective in the presence of the fillers and depended on the type of the filler but not on its amount. Moreover, the oriented samples experienced more effective photooxidation compared with the unoriented ones. In all studied samples the same photoproducts were detected, suggesting the same route of polymer photooxidation with and without the filler. These polymeric films were produced for potential applications in the devices in which piezoelectric effect can be used.

Photochemical Reactions in Dialdehyde Starch.

In this study potato and corn starch were subjected to oxidation, using sodium periodate, to obtain dialdehyde starch (DAS) containing different amount of aldehyde groups. The obtained modified starch samples have been characterized with chemical analysis, scanning electron microscopy (SEM) and ATR-FTIR spectroscopy. Then, the samples were exposed to polychromatic UV radiation and the course of photochemical reaction has been monitored with ATR-FTIR spectroscopy. The surface properties of the native and dialdehyde starch before and after UV-irradiation have been determined by contact angle measurements and calculation of surface free energy. The crystallinity of the samples has been estimated with X-ray diffraction (XRD). It has been proved that the dialdehyded corn starch contained a higher amount of functional groups was more photostable than the oxidized potato starch. Sodium iodide(V), firmly bound to DAS macromolecules, has been found to have a significant effect on the photooxidative degradation of the tested systems. In addition, the mechanism of photoinduced reactions in the dialdehyde starch has been proposed.

The chitosan - Porphyrazine hybrid materials and their photochemical properties.

Three magnesium sulfanyl porphyrazines differing in the size of peripheral substituents (3,5-dimethoxybenzylsulfanyl, (3,5-dimethoxybenzyloxy)benzylsulfanyl, 3,5-bis[(3,5-bis[(3,5-dimethoxybenzyloxy)benzyloxy]benzylsulfanyl) were exposed to visible and ultraviolet radiation (UV A + B + C) in order to determine their photochemical properties. The course of photochemical reactions in dimethylformamide solutions and the ability of the systems to generate singlet oxygen were studied by UV-Vis spectroscopy, which additionally gave information on aggregation processes. The porphyrazines were found to be stable upon visible light irradiation conditions, but when exposed to high energy UV radiation, the efficient photodegradation of these macrocycles was observed. Therefore, these three magnesium sulfanyl porphyrazines were incorporated into chitosan matrix. The obtained thin films of chitosan doped with porphyrazines were subjected to polychromatic UV-radiation and studied by spectroscopic methods (UV-Vis, FTIR), scanning electron microscopy (SEM) and atomic force microscopy (AFM). Application of chitosan as a polymer matrix for porphyrazines was found to be successful method that effectively stopped the unwelcome degradation of macrocycles, thus worth considering for their photoprotection. In addition, the surface properties of the hybrid material were determined by contact angle measurements and calculation of surface free energy. Intermolecular interactions between these novel porphyrazines and chitosan were detected. The mechanism of photochemical reactions occurring in studied systems has been discussed.

Studies of chitosan/pectin complexes exposed to UV radiation.

Chitosan and pectin form complexes owing to electrostatic interactions between positively charged amino groups in chitosan and negatively charged carboxylate groups in pectin, which was confirmed by ATR-FTIR spectroscopy and contact angle measurements. Moreover, the formation of these complexes might be associated with the loss of the biopolymers ordering, which resulted in higher surface roughness and lower thermal stability of the complexes in comparison to those of homopolymers. UV rays, used as a sterilizing agent, caused a moderate increase in the surface polarity of the complexes. Roughness parameters of these samples changed irregularly after irradiation, and their thermal stability was slightly affected by UV rays. The results indicated that the complexes studied appeared to present resistance to UV action higher than homopolymers, which is a desirable property in medical or pharmaceutical applications.