Ion-imprinted chitosan prepared without cross-linking agent for efficient selective adsorption of Al(III) from rare earth solution.

In the aqueous phase, ion-imprinted materials exhibit excellent selective adsorption properties for specific ions, but their complicated preparation process and large amount of crosslinker consumption limit their application. In this study, ion-imprinted chitosan (IIP-CS) was prepared by a simple one-step hydrothermal method without a cross-linking agent for the efficient adsorption of trace amounts of Al(III) from a rare earth solution. The structures and morphology of IIP-CS were analyzed by FT-IR, SEM, and XRD. The Al(III) adsorption characteristics of IIP-CS were investigated under various preparation processes and adsorption conditions. It was found that the optimum mass ratio of IIP-CS is 3 : 1 and pH is 3 and the adsorption capacity reaches up to 40.36 mg g-1. In addition, three different isothermal models-Temkin, Freundlich, and Langmuir-were used to analyze the equilibrium adsorption of IIP-CS in aqueous solution. The results obtained are consistent with the Langmuir model. The adsorption process of Al(III) on IIP-CS follows a pseudo-secondary kinetic model, suggesting that electron sharing or exchange between IIP-CS and Al(III) is a key factor affecting its adsorption rate. IIP-CS shows high selectivity coefficients for Al(III) in mixtures of La(III), Y(III), and Gd(III), which are 792.50, 163.26, and 55.16, respectively. The mechanism of action is the formation of a complex via amidation between Al(III) and IIP-CS. IIP-CS is an adsorbent with excellent regeneration and selective adsorption performance in aqueous solution.

Preparation of chitosan mesoporous membrane/halloysite composite for efficiently selective adsorption of Al(III) from rare earth ions solution through constructing pore structure on substrate.

The removal of impurity Al(III) from rare earth ion solution by selective adsorption method was one of the challenging tasks. Herein, calcination and acid dissolution treatment were used to construct the pore structure for the halloysite substrate (Hal-650-H) and provide conditions for the formation of the chitosan mesoporous membrane to prepare composite (Hal-H-2CS). The selective adsorption properties and mechanism of the Hal-H-2CS for Al(III) in the rare earth ion solution were studied. The results showed that the formation of mesoporous structures for chitosan provided abundant sites for the adsorption of Al(III). Hal-H-2CS showed remarkable selective adsorption properties for Al(III) in a wide pH range and the binary mixtures with high content of Al(III) or La(III). The maximum adsorption capacity of Al(III) was 106 mg/g, while the adsorption capacity of La(III) was only 1.41 mg/g at pH 4.0. In addition, the Hal-H-2CS exhibited excellent regeneration and structural stability. The remarkable selective properties of Hal-H-2CS was achieved by the synergistic effect between chitosan mesoporous membrane and Hal-650-H, the main adsorption sites were the OH, NH2, CONH2 of chitosan and the oxygen sites of the Hal-650-H. This work provides a new strategy for the design and preparation of outstanding selective adsorbent for Al(III).

Facile preparation of MoS2@Kaolin composite by one-step hydrothermal method for efficient removal of Pb(II).

MoS2@Kaolin was prepared by facile one-step hydrothermal method for the efficient adsorption of Pb(II) from aqueous solution. XRD, TG, SEM, BET, XPS and FTIR were used to characterize the phase and structure of composite before and after the adsorption of Pb(II). The results showed that MoS2 nanosheets were successfully assembled on kaolinite surface to form MoS2@Kaolin, and the adsorption capacity of the MoS2@Kaolin is 1.74 and 16.95 times than that of single MoS2 and kaolinite, respectively. MoS2@Kaolin composite exhibited a fast adsorption rate for Pb(II) and an excellent adsorption efficiency for Pb(II) in a wide pH range (2-5.5). The adsorption process followed the Langmuir isotherm model and maximum adsorption capacity was 280.39 mg/g. The adsorption kinetics of MoS2@Kaolin composite to Pb(II) fitted well with the pseudo-second-order kinetics models, which showed that the adsorption process was controlled by chemical sorption. MoS2@Kaolin showed excellent regeneration and maintained high selectivity adsorption with co-existence metal ions. The adsorption mechanism was that the Pb(II) reacted with the S atoms on surface of MoS2@Kaolin under oxidation conditions provided by molybdenum disulfide to form the insoluble compound ß-Pb3O2SO4 in aqueous solution. MoS2@Kaolin was an adsorbent for Pb(II) in aqueous solution with excellent adsorption properties and application potential.