Fluorimetric determination of aqueous formaldehyde employing heating and ultrasound-assisted approach through its derivatization with a ß-diketone-nickel(2+) complex immobilized in a PMMA flow cell.

Formaldehyde (FA) is a highly toxic substance present in many matrices, including freshwater as well as found in natural mechanisms such as rainfall and combustion of organic matter. Consumption of water contaminated with high levels of FA can cause severe short-term or long-term health problems. Due to these health risks, procedures are necessary to determine and quantify FA in aqua sources This paper reports on a study of fluorimetric determination of FA using a nickel(2 + )-diketonate coordination compound immobilized as a solid precursor. The compound was characterized by electronic absorption, Fourier transform infrared (FTIR) spectroscopy, X-ray diffraction (XRD), thermogravimetry (TG), optical microscopy (OM), and scanner electron microscopy (SEM). The methodology was based on the reaction of the synthesized compound with an ammoniacal buffer generating a selective reagent for formaldehyde: fluoral-P. The product of the reaction generates 3,5-diacetyl-1,4-dihydrolutidine (DDL), which is responsible for the fluorescence of the system. Several parameters such as temperature, duration of heating time, and dilution effect with the best effects were studied to carry out FA determination. Under the optimum experimental conditions, a linear response ranging from 1.0 to 10.0 mg/L FA (R = 0.997 and n = 10), and a detection (3σ criterion) and quantification (10 σ criterion) limit estimated at 0.129 and 0.389 mg/L, respectively were achieved. The FA analysis was able to be conducted in 05 min with a relative standard deviation estimated at 1.10 %.

Microwave-assisted digestion employing diluted nitric acid for mineral determination in rice by ICP OES.

A microwave-assisted digestion method using diluted HNO3 was developed for further determination of Al, Ca, Cr, Cu, Fe, K, Mn, Mo and Ni in rice samples by ICP OES. The following optimized conditions were established after full factorial design: digestion time of 14 min, concentration of 1 mol L-1 HNO3 and 2.5 mL of H2O2. The efficiency in decomposing organic matter with diluted acid was higher than 89%. The methodology was validated using the SRM NIST 1568a Rice Flour and recovery tests, with agreement between the determined and certified/added concentration values, and RSD of up to 12%. The limits of detection of the method were in the range of 0.0087 mg kg-1 (Mn) to 1.6 mg kg-1 (Ca). In addition, a simple and inexpensive spectrophotometric method was proposed for the quantification of organic carbon in varied samples (carbohydrates, proteins, lipids) in the form of digested or solids.

Potentiometric perchlorate determination at nanomolar concentrations in vegetables.

In this work, an expeditious method based on the multi-commutated flow-analysis concept with potentiometric detection is proposed to perform determinations of the emergent contaminant perchlorate in vegetable matrices down to nanomolar concentration. To accomplish the task, a tubular shaped potentiometric sensor selective to perchlorate ion was constructed with a PVC membrane containing 12mmol/kg of the polyamine bisnaphthalimidopropyl-4,4'-diaminodiphenylmethane and 2-nitrophenyl phenyl ether 68% (w/w) as plasticizer casted on a conductive epoxy resin. Under optimal flow conditions, the sensor responded linearly in the concentration range of 6.3×10-7-1.0×10-3mol/L perchlorate. In order to extend the determinations to lower concentrations (4.6(±1.3)×10-10mol/L perchlorate), a column packed with 70mg of sodium 2,5,8,11,14-pentaoxa-1-silacyclotetradecane-polymer was coupled to the flow-system thus enabling prior pre-concentration of the perchlorate. The proposed procedure provides a simpler alternative for the determination of perchlorate in foods, nowadays only allowed by sophisticated and expensive equipment and laborious methods.

In-line electrochemical reagent generation coupled to a flow injection biamperometric system for the determination of sulfite in beverage samples.

This work reports an in-line electrochemical reagent generation coupled to a flow injection biamperometric procedure for the determination of SO3(2-). The method was based on a redox reaction between the I3(-) and SO3(2-) ions, after the diffusion of SO2 through a gas diffusion chamber. Under optimum experimental conditions, a linear response ranging from 1.0 to 12.0 mg L(-1) (R=0.9999 and n=7), a detection and quantification limit estimated at 0.26 and 0.86 mg L(-1), respectively, a standard deviation relative of 0.4% (n=10) for a reference solution of 4.0 mg L(-1) SO3(2-) and sampling throughput for 40 determinations per hour were achieved. Addition and recovery tests with juice and wine samples were performed resulting in a range between 92% and 110%. There were no significant differences at a 95% confidence level in the analysis of eight samples when comparing the new method with a reference procedure.

Employment of electrochemically synthesized TGA-CdSe quantum dots for Cr(3+) determination in vitamin supplements.

The fluorescence quenching of TGA-CdSe quantum dots (QDs) was used for Cr(3+) quantification in vitamin supplements. The QD was electrochemically synthesized, demonstrating high reproducibility with control of particle size, thus making it a clean method, without the presence of reducing agents. Under ideal conditions, with the fluorescence band at 551 nm (excitation 365 nm), the maximum fluorescence quenching was observed at pH 4.0, with a time of 200 s for each data acquisition. Under optimum experimental conditions, linear quenching was observed for Cr(3+) in the range of 25.0-325.0 ng L(-1) (R=0.9996, n=6), a limit of detection of 5.67 ng L(-1), and relative standard deviation of 4.43% (n=10). The recovery test for Cr(3+) quantification in vitamin supplements presented results from 82% to 98%. These Cr(3+) determination results were compared to the same vitamin supplement sample using flame atomic absortion spectrometry (FAAS) method, and no significant differences were observed at 95% confidence level.

A spectrophotometric procedure for malic acid determination in wines employing a multicommutation approach.

This work describes an automated procedure to determine L-malic acid (MA) in wine samples using a multicommuted flow analysis. The MA quantification was based on an enzymatic reaction between MA and L-malate dehydrogenase (L-MDH) in the presence of nicotinamide adenine dinucleotide (NAD(+)), producing nicotinamide adenine dinucleotide dehydrogenase (NADH), which was monitored at 340 nm. The L-MDH was immobilized on a surface of modified silica with amino groups in the presence of glutaraldehyde. For studying optimization, the system was maintained with 200 µL (288 U) of the L-MDH in 0.5 g of modified silica. Under the optimum experimental conditions, a linear response ranging from 0.1 to 1.5 g L(-1) MA (R = 0.997 and n = 7), a detection (3σ criterion) and quantification (10σ criterion) limit estimated at 0.02 and 0.06 g L(-1), respectively, a standard deviation relative of 1.8% (n = 7) for a sample of 0.5 g L(-1) MA, a sampling rate of 67 samples per hour were achieved. Analyzing ten wines samples and applying the t-test to the results found and those obtained using reference procedures (HPLC) provided no significant differences at the 95% confidence level.

Luminescent solid phase for sialic acid determination: a promising sensor for milk-adulterated samples.

This article presents the synthesis, characterization and spectroscopic study of silica modified with thenoyltrifluoroacetonate (SilTTA) and coordinated to an europium (III) ion, for the determination of sialic acid (NANA). Elemental analysis and infrared spectroscopy suggest silica functionalization, as well as coordination of beta-diketone to the lanthanide ion. The emission spectra of compound-free and coordinated Eu-SilTTA to NANA showed significant changes with respect to the maximum emission and spectral profile, suggesting that the NANA ion is coordinated to the Eu(III). The values of the phenomenological intensity parameters show an increase in polarizability around the Eu(III) in the case of Eu-SilTTA coordinated to NANA, as expected, since water molecules are less polarizable than sialic acid. The results of the batch assay showed that luminescent silica can be used for sialic acid determination in milk-adulterated samples, with a correlation coefficient of 0.9992; and a detection limit of 0.4 mg/L; relative standard deviation (RSD%) = 0.0028.

A multicommuted stop-flow system employing LEDs-based photometer for the sequential determination of anionic and cationic surfactants in water.

It has been developed an automatic stop-flow procedure for sequential photometric determination of anionic and cationic surfactants in a same sample of water. The flow system was based on multicommutation process that was designed employing two solenoid micro-pumps and six solenoid pinch valves, which under microcomputer control carry out fluid propelling and reagent solutions handling. A homemade photometer using a photodiode as detector and two light emitting diodes (LEDs) with emission at 470 nm (blue) and 650 nm (red) as radiation sources, which was tailored to allow the determination of anionic and cationic surfactants in waters. The procedure for anionic surfactant determination was based on the substitution reaction of methyl orange (MO) by the anionic surfactant sodium dodecylbenzene sulfonate (DBS) to form an ion-pair with the cetyl pyridine chloride (CPC). Features such as a linear response ranging from 0.35 to 10.5 mg L(-1) DBS (R=0.999), a detection limit of 0.06 mg L(-1) DBS and a relative standard deviation of 0.6% (n=11) were achieved. For cationic surfactant determination, the procedure was based on the ternary complex formation between cationic surfactant, Fe(III) and chromazurol S (CAS) using CPC as reference standard solution. A linear response range between 0.34 and 10.2 mg L(-1) CPC (R=0.999), a detection limit of 0.05 mg L(-1) CPC and a relative standard deviation of 0.5% (n=11) were obtained. In both cases, the sampling throughput was 60 determinations per hour. Reagents consumption of 7.8 microg MO, 8.2 microg CPC, 37.2 microg CAS and 21.6 microg Fe(III) per determination were achieved. Analyzing river water samples and applying t-test between the results found and those obtained using reference procedures for both surfactant types provide no significant differences at 95% confidence level.

Monitoring of the smoking process by multicommutation Fourier transform infrared spectroscopy.

Nicotine was selected as the target molecule for monitoring of the smoking process by multicommutation Fourier Transform Infrared spectroscopy (FTIR). The method involved the use of CHCl3 for on-line extraction of nicotine from tobacco, cigarette filters and tobacco ash from NH4OH alkalinized samples, and absorbance measurement of the characteristic band at 1316 cm(-1) in the stopped-flow mode, by obtaining the peak area in the range between 1334 and 1300 cm(-1). Under the best operational conditions, the procedure developed provided a detection limit of 0.05 mg mL(-1) nicotine, corresponding to 0.5 mg g(-1) in the solid sample, a relative standard deviation less than 2.5%, and a sampling frequency of 12 determinations h(-1). It can be concluded that nicotine migrates in the smoke mainstream towards the filter during the smoking process. The smoking of cigarettes and cigars is different. Nicotine is retained weakly by both tobacco and filter in the case of cigarettes, and strongly by the unburned tobacco in cigars. The incomplete smoking of cigars and cigarettes reduces nicotine intake and thus reduces the additive effect.

Micropumping multicommutation turbidimetric analysis of waters.

A micropumping multicommutation manifold to perform turbidity determinations in waters is described. The procedure is based on the use of a combination of hydrazine sulfate and hexamethylenetetramine, to obtain an external standard of nephelometric turbidity units (NTU), which could compare the absorbance measurements at high wavelengths for samples with a calibration line obtained from a concentrated formazine standard diluted on-line. To minimize sample and reagent consumption and waste generation, the flow system was designed with two solenoid micro-pumps, one of them for the alternative introduction of the formazine standard and samples and the other one for the water carrier. The multicommutation approach makes possible the on-line dilution of a single standard to obtain the external calibration. The linear response was ranged up to 160NTU. The coefficient of variation was estimated as 1.6 and 3.2% for 10 and 100mm flow cell, respectively, for solutions containing 40NTU (n=10). Approximately, 60 determinations can be carried out per hour with limit of detection values of 1 and 0.1NTU, consuming only 160 or 240muL formazine solution and generating 1.8 or 2.0mL waste per determination, using measurement cells of 10 and 100mm optical pathlength, respectively. The procedure was successfully applied to 11 different water samples. Recovery studies were carried out and results obtained were between 97.5+/-0.2 and 100+/-1%. The development of a homebuilt light emitting diode (LED)-based portable flow analysis instrument was checked for in situ turbidimetric measurements, providing this equipment a LOD value of 0.09NTU working with a blue LED at 464nm and a LOD value of 0.1NTU working with an IR LED.

Multicommuted flow system employing pinch solenoid valves and micro-pumps. Spectrophotometric determination of paracetamol in pharmaceutical formulations.

A multicommuted spectrophotometric flow-based procedure for the determination of paracetamol in pharmaceutical formulations is proposed. The method is based on the reaction of paracetamol with sodium hypochlorite forming N-acetyl-p-benzoquinoneimine, which reacts with sodium salicylate in alkaline medium producing a blue indophenol dye that was measured at 640nm. The flow system was designed employing four pinch solenoid valves and two solenoid micro-pumps, which were assembled aiming to obtain a compact module, resulting in minimization of reagents consumption and waste generation. Aiming to prove the usefulness of flow system an analytical procedure for paracetamol determination in pharmaceutical formulations was developed. To allow accuracy assessment samples were also analyzed using the AOAC reference method. Applying the paired t-test between results no significant difference at the 95% confidence level was observed. Other profitable features such as a linear response ranging from 5.0 to 125.0mgl(-1) (R=0.9992, n=7), a sampling rate of 60 determinations per hour, a detection limit of 0.4mgl(-1) paracetamol, a relative standard deviation of 1.5% (n=11) for a typical sample solution containing 25.0mgl(-1) paracetamol, reagent consumption of 1.28mg sodium hypochlorite and 6.4mg sodium salicylate per determination were also achieved.

Micro-pumping flow system for spectrophotometric determination of anionic surfactants in water.

A novel procedure has been developed for spectrophotometric determination of anionic surfactants in water using a solenoid micro-pump as fluid-propulsion device. The proposed method is based on substitution of methyl orange (MO) by anionic surfactants in the formation of an ion-pair with the cetyl pyridine ion (CPC+) at pH 5.0. The flow network comprised four solenoid micro-pumps which, under microcomputer control, enabled sample and reagent introduction, and homogenisation in the reaction zone. The system is flexible and simple to operate and control, and sensitive and precise. The analytical plot for the anionic surfactant was linear between 1.43x10(-6) and 1.43x10(-5) mol L(-1) (0.5 to 5.0 mg L(-1); R=0.997, n=5). The relative standard deviation was 0.8% (n=11) for a sample containing 5.74x10(-6) mol L(-1) (2 mg L(-1)) surfactant. The limit of detection was 9.76x10(-8) mol L(-1) (0.034 mg L(-1)) and the sampling throughput was 60 determinations per hour. The results obtained for washing-water samples were comparable with those obtained by use of the reference method, and no significant differences at the 95% confidence level were observed.

Identification of a metallothionein in Synechococcus by capillary electrophoresis hyphenated with inductively coupled plasma mass spectrometry.

A home-made system hyphenating capillary electrophoresis with an inductively coupled plasma mass spectrometer (CE-ICP-MS) for cadmium speciation of protein-binding and free cadmium ions in solution is presented. The CE-ICP-MS interface consisted of an acrylic block with an internal volume ca. 20 microL in which a platinum electrode, a capillary column, and a connection to an ICP nebulizer were inserted. A make-up electrolyte solution containing 50 mmol L(-1) Tris-HCl buffer solution (pH 9.0) was continuously flowed through the interface to the ICP nebulizer. The separation of free Cd ions, Cd-cysteine, and Cd bounded to metallothionein (MT) isoforms from rabbit liver was carried out by capillary electrophoresis, and the analytes were detected by ICP-MS. The feasibility to isolate metallothionein compounds extracted from the cyanobacterium Synechococcus PCC7942 was demonstrated. The Cd binding proteins were induced in Synechococcus PCC7942 and further analyzed by CE ICP-MS.