Lipase-catalyzed solvent-free synthesis of monoglycerides from biodiesel-derived crude glycerol: Optimized using response surface methodology.

The growth of the biodiesel industry has resulted in significant quantity of crude glycerol. It is necessary to explore the synthesis of high-value-added products from crude glycerol. In this study, the enzymatic synthesis of monoglycerides under solvent-free conditions, employing crude glycerol as the primary feedstock, had been investigated. The analysis showed that the highest yield of monoglycerides was obtained after 12 h, and Novozym 435 showed the highest monoglyceride yield of 18.41 % among the three lipases tested, followed by Lipozyme TL IM and Lipozyme RM IM. Monoglycerides were synthesized from biodiesel-derived crude glycerol using Novozym 435 as the catalyst under solvent-free conditions at different parameters, which were catalyst concentration, substrate molar ratio, and temperature. The yield of monoglycerides was examined in single-factor experiments. Response surface methodology (RSM) was subsequently employed to optimize the synthesis conditions based on the single-factor experimental results. The optimal conditions were at an enzyme concentration of 12.7 wt% and a molar ratio of crude glycerol:oil of 5.7:1 at a reaction temperature of 65.2 °C. The experimental yield of monoglycerides under the optimal conditions was 28.93 %, which is close to the value predicted from the RSM model (29.02 %).

A systematic review on utilization of biodiesel-derived crude glycerol in sustainable polymers preparation.

With the rapid development of biodiesel, biodiesel-derived glycerol has become a promising renewable bioresource. The key to utilizing this bioresource lies in the value-added conversion of crude glycerol. While purifying crude glycerol into a pure form allows for diverse applications, the intricate nature of this process renders it costly and environmentally stressful. Consequently, technology facilitating the direct utilization of unpurified crude glycerol holds significant importance. It has been reported that crude glycerol can be bio-transformed or chemically converted into high-value polymers. These technologies provide cost-effective alternatives for polymer production while contributing to a more sustainable biodiesel industry. This review article describes the global production and quality characteristics of biodiesel-derived glycerol and investigates the influencing factors and treatment of the composition of crude glycerol including water, methanol, soap, matter organic non-glycerol, and ash. Additionally, this review also focused on the advantages and challenges of various technologies for converting crude glycerol into polymers, considering factors such as the compatibility of crude glycerol and the control of unfavorable factors. Lastly, the application prospect and value of crude glycerol conversion were discussed from the aspects of economy and environmental protection. The development of new technologies for the increased use of crude glycerol as a renewable feedstock for polymer production will be facilitated by the findings of this review, while promoting mass market applications.

Thymol-Loaded Polymeric Nanoparticles Improve the Postharvest Microbiological Safety of Blueberries.

Research background: The presence of Yersinia enterocolitica on raw food products raises the concern of yersiniosis as most of the berries are consumed raw. This is a challenging issue from the food safety aspect since it could increase the occurrence of foodborne diseases among humans. Thus, it is crucial to implement an effective sanitation before the packaging. Experimental approach: This study aims to synthesize and characterize thymol-loaded polyvinyl alcohol (Thy/PVA) nanoparticles as a sanitizer for postharvest treatment of blueberries. Thy/PVA nanoparticles were characterized by spectroscopic and microscopic approaches, prior to the analyses of antimicrobial properties. Results and conclusions: The diameter size of the nanoparticles was on average 84.7 nm, with a surface charge of -11.73 mV. Based on Fourier transform infrared (FTIR) measurement, the Thy/PVA nanoparticles notably shifted to the frequency of 3275.70, 2869.66, 1651.02 and 1090.52 cm-1. A rapid burst was observed in the first hour of release study, and 74.9 % thymol was released from the PVA nanoparticles. The largest inhibition zone was displayed by methicillin-resistant Staphylococcus aureus (MRSA), followed by Y. enterocolitica and Salmonella typhi. However, amongst these bacteria, the inhibition and killing of Y. enterocolitica required a lower concentration of Thy/PVA nanoparticles. The treatment successfully reduced the bacterial load of Y. enterocolitica on blueberries by 100 %. Novelty and scientific contribution: Thymol is a plant-based chemical without reported adverse effects to humans. In this study, by using the nanotechnology method of encapsulation with PVA, we improved the stability and physicochemical properties of thymol. This nanoparticle-based sanitizer could potentially promote the postharvest microbiological safety of raw berries, which may become an alternative practice of food safety.

Thermoplastic starch (TPS) bioplastic, the green solution for single-use petroleum plastic food packaging - A review.

Plastic throughout the years is now one of the biggest world commodities and also the largest pollution to have an environmental impact, accumulating in landfills and also leaching into water systems and oceans. Especially with the shift to single-use disposable plastic, evermore positions plastics as the number one novel entity that pollutes the earth. This shift is also consistent in the food packaging industry. Managing plastic waste is still an issue at large, while the process of pyrolysis incineration still requires an obscene amount of energy that also does not resolve the problems with its environmental impact, the cost of mechanical-chemical degradation even outweighs the cost of producing the materials, and biodegradation process is a very slow and long process. Converting to bioplastics is one of the potential solutions to the global plastic issue. This review covers the potentials, limitations, challenges, progress and advancements of bioplastics, especially thermoplastic starch (starch-based bioplastic) in their efforts to replace petroleum plastics in food packaging and smart food packaging, especially for single-use (disposable) food packaging.

Recent Advances in the Enzymatic Synthesis of Polyester.

Polyester is a kind of polymer composed of ester bond-linked polybasic acids and polyol. This type of polymer has a wide range of applications in various industries, such as automotive, furniture, coatings, packaging, and biomedical. The traditional process of synthesizing polyester mainly uses metal catalyst polymerization under high-temperature. This condition may have problems with metal residue and undesired side reactions. As an alternative, enzyme-catalyzed polymerization is evolving rapidly due to the metal-free residue, satisfactory biocompatibility, and mild reaction conditions. This article presented the reaction modes of enzyme-catalyzed ring-opening polymerization and enzyme-catalyzed polycondensation and their combinations, respectively. In addition, the article also summarized how lipase-catalyzed the polymerization of polyester, which includes (i) the distinctive features of lipase, (ii) the lipase-catalyzed polymerization and its mechanism, and (iii) the lipase stability under organic solvent and high-temperature conditions. In addition, this article also focused on the advantages and disadvantages of enzyme-catalyzed polyester synthesis under different solvent systems, including organic solvent systems, solvent-free systems, and green solvent systems. The challenges of enzyme optimization and process equipment innovation for further industrialization of enzyme-catalyzed polyester synthesis were also discussed in this article.

Factors Affecting Mechanical Properties of Reinforced Bioplastics: A Review.

The short life cycle and recalcitrant nature of petroleum-based plastics have been associated with plastic waste accumulation due to their composition rather than worldwide overproduction. The drive to replace single-use products has sparked a considerable amount of research work to discover sustainable options for petroleum-based plastics. Bioplastics open up a new horizon in plastics manufacturing operations and industrial sectors because of their low environmental impact, superior biodegradability, and contribution to sustainable goals. Their mechanical properties regarding tensile, flexural, hardness, and impact strength vary substantially. Various attempts have been made to augment their mechanical characteristics and capacities by incorporating reinforcement materials, such as inorganic and lignocellulosic fibres. This review summarizes the research on the properties of bioplastics modified by fibre reinforcement, with a focus on mechanical performance. The mechanical properties of reinforced bioplastics are significantly driven by parameters such as filler type, filler percentage, and aspect ratio. Fibre treatment aims to promote fibre-matrix adhesion by changing their physical, chemical, thermal, and mechanical properties. A general overview of how different filler treatments affect the mechanical properties of the composite is also presented. Lastly, the application of natural fibre-reinforced bioplastics in the automobile, construction, and packaging industries is discussed.

Biogenic Silver Nanoparticles of Clinacanthus nutans as Antioxidant with Antimicrobial and Cytotoxic Effects.

Silver nanoparticles (AgNPs) previously synthesised using leaf (AgNP-L) and stem (AgNP-S) extracts of Clinacanthus nutans (C. nutans) were tested to evaluate antimicrobial, antioxidant, and cytotoxicity activities. The AgNPs showed good inhibition against bacteria, but not fungi. The inhibition results showed the highest activity against Staphylococcus aureus (S. aureus) with 11.35 mm (AgNP-L) and 11.52 mm (AgNP-S), while the lowest inhibition was against Escherichia coli (E. coli) with 9.22 mm (AgNP-L) and 9.25 mm (AgNP-S) in the disc diffusion method. The same trend of results was noted in the well diffusion method. The IC50 of AgNP-L and AgNP-S in 2,2-diphenyl-1-picrylhydrazyl (DPPH) and 2,2'-azino-bis (3-ethylbenzothiazoline-6-sulfonic acid) (ABTS) assays was 417.05 µg/mL and 434.60 µg/mL, as well as 304.31 µg/mL and 326.83 µg/mL, respectively. Ferric reducing power (FRAP) assay showed that AgNP-L [872.389 µmol/L Fe(II)] and AgNP-S [612.770 µmol/L Fe(II)] exhibited significantly (p < 0.05) greater antioxidant activities than leaf extract (CNL) [152.260 µmol/L Fe(II)] and stem extract (CNS) [110.445 µmol/L Fe(II)] of C. nutans. The AgNPs were also proven to possess cytotoxic effects on the breast (MCF-7), cervical (HeLa), and colon (HT-29) cancer cells in a dose-dependent manner. AgNP-S and AgNP-L showed significantly (p < 0.05) higher cytotoxicity against MCF-7 (117.43 µg/mL) and HT-29 (78.47 µg/mL), respectively. In conclusion, the biosynthesised AgNPs from aqueous extract leaves and stem of C. nutans have demonstrated promising potential towards antioxidant, antimicrobial, and cytotoxicity activities.

Statistical Optimization of Flavonoid and Antioxidant Recovery from Macerated Chinese and Malaysian Lotus Root (Nelumbo nucifera) Using Response Surface Methodology.

In this study, the combination of parameters required for optimal extraction of anti-oxidative components from the Chinese lotus (CLR) and Malaysian lotus (MLR) roots were carefully investigated. Box-Behnken design was employed to optimize the pH (X1: 2-3), extraction time (X2: 0.5-1.5 h) and solvent-to-sample ratio (X3: 20-40 mL/g) to obtain a high flavonoid yield with high % DPPHsc free radical scavenging and Ferric-reducing power assay (FRAP). The analysis of variance clearly showed the significant contribution of quadratic model for all responses. The optimal conditions for both Chinese lotus (CLR) and Malaysian lotus (MLR) roots were obtained as: CLR: X1 = 2.5; X2 = 0.5 h; X3 = 40 mL/g; MLR: X1 = 2.4; X2 = 0.5 h; X3 = 40 mL/g. These optimum conditions gave (a) Total flavonoid content (TFC) of 0.599 mg PCE/g sample and 0.549 mg PCE/g sample, respectively; (b) % DPPHsc of 48.36% and 29.11%, respectively; (c) FRAP value of 2.07 mM FeSO4 and 1.89 mM FeSO4, respectively. A close agreement between predicted and experimental values was found. The result obtained succinctly revealed that the Chinese lotus exhibited higher antioxidant and total flavonoid content when compared with the Malaysia lotus root at optimum extraction condition.

Bioseparation of phycocyanin from Phormidium tergestinum using an aqueous two-phase system.

This study aimed at purification of phycocyanin (PC) from Phormidium tergestinum using an aqueous two-phase system (ATPS) comprised of polyethylene glycol (PEG) and salts. The partitioning efficiency of PC in ATPS and the effect of phase composition, pH, crude loading, and neutral salts on purification factor and yield were investigated. Results showed that PC was selectively partitioned toward bottom phase of the system containing potassium phosphate. Under optimum conditions of 20% (w/w) PEG 4000, 10% (w/w) potassium phosphate, 20% (v/v) crude load at pH 7, with addition of 0.5% (w/w) NaCl, PC from P. tergestinum was partially purified up to 5.34-fold with a yield of 87.8%. Sodium dodecyl sulfate-polyacrylamide gel electrophoresis showed that the molecular weight of PC was ∼19 kDa. Results from this study demonstrated ATPS could be used as a potential approach for the purification of PC from P. tergestinum.

Response surface methodology optimization of polyhydroxyalkanoate production by Burkholderia cepacia BPT1213 using waste glycerol from palm oil-based biodiesel production.

The feasibility of using waste glycerol from the biodiesel industry for biosynthesis of polyhydroxyalkanoate (PHA) by Burkholderia cepacia BPT1213 was evaluated. Culture conditions were optimized by growing B. cepacia BPT1213 in mineral salt medium supplemented with 2% waste glycerol in a 2.5 L bioreactor. Response surface methodology was used to determine the influence of aeration rate (0.6-1.8 vvm), agitation speed (100-300 rpm), and cultivation period (48-72 hr) on PHA production. The optimum conditions for the growth and PHA accumulation were 1.5 vvm, 300 rpm, and 72 hr, with predicted values of 5.08 g/L cell dry weight (CDW), 66.07% PHA content, and 3.35 g/L total PHA concentration. Using these conditions, the experimental system produced 5.63 g/L of CDW with 64.00% wt/wt PHA content, which is threefold higher PHA concentration (3.60 g/L) compared to the non-optimized conditions. The melting temperature (Tm ) of purified PHA was 173.45 ± 1.05°C. In conclusion, the statistical approach was significantly increased the PHA production using waste glycerol as the sole carbon source.

Optimization of biogenic synthesis of silver nanoparticles from flavonoid-rich Clinacanthus nutans leaf and stem aqueous extracts.

Background: Silver nanoparticles (AgNPs) are widely used in food industries, biomedical, dentistry, catalysis, diagnostic biological probes and sensors. The use of plant extract for AgNPs synthesis eliminates the process of maintaining cell culture and the process could be scaled up under a non-aseptic environment. The purpose of this study is to determine the classes of phytochemicals, to biosynthesize and characterize the AgNPs using Clinacanthus nutans leaf and stem extracts. In this study, AgNPs were synthesized from the aqueous extracts of C. nutans leaves and stems through a non-toxic, cost-effective and eco-friendly method. Results: The formation of AgNPs was confirmed by UV-Vis spectroscopy, and the size of AgNP-L (leaf) and AgNP-S (stem) were 114.7 and 129.9 nm, respectively. Transmission electron microscopy (TEM) analysis showed spherical nanoparticles with AgNP-L and AgNP-S ranging from 10 to 300 nm and 10 to 180 nm, with average of 101.18 and 75.38 nm, respectively. The zeta potentials of AgNP-L and AgNP-S were recorded at -42.8 and -43.9 mV. X-ray diffraction analysis matched the face-centred cubic structure of silver and was capped with bioactive compounds. Fourier transform infrared spectrophotometer analysis revealed the presence of few functional groups of phenolic and flavonoid compounds. These functional groups act as reducing agents in AgNPs synthesis. Conclusion: These results showed that the biogenically synthesized nanoparticles reduced silver ions to silver nanoparticles in aqueous condition and the AgNPs formed were stable and less toxic.

Application of bacteriocins in food preservation and infectious disease treatment for humans and livestock: a review.

Infectious diseases caused by bacteria that can be transmitted via food, livestock and humans are always a concern to the public, as majority of them may cause severe illnesses and death. Antibacterial agents have been investigated for the treatment of bacterial infections. Antibiotics are the most successful antibacterial agents that have been used widely for decades to ease human pain caused by bacterial infections. Nevertheless, the emergence of antibiotic-resistant bacteria has raised awareness amongst public about the downside of using antibiotics. The threat of antibiotic resistance to global health, food security and development has been emphasized by the World Health Organization (WHO), and research studies have been focused on alternative antimicrobial agents. Bacteriocin, a natural antimicrobial peptide, has been chosen to replace antibiotics for its application in food preservation and infectious disease treatment for livestock and humans, as it is less toxic.

Isolation and characterization of Enterococcus faecium DSM 20477 with ability to secrete antimicrobial substance for the inhibition of oral pathogen Streptococcus mutans UKMCC 1019.

Streptococcus mutans and Candida albicans are the main oral pathogens which contribute to dental caries that affects all ages of human being. OBJECTIVES: This study focuses on the potential of crude cell free supernatant (CCFS) from lactic acid bacteria (LAB) to inhibit of the growth of S. mutans UKMCC 1019. DESIGN: A total of 61 CCFS from LAB strains were screened for their inhibitory ability against S. mutans UKMCC 1019 by broth microdilution method. The selected LAB with highest antimicrobial activity was identified and its CCFS was characterized for pH stability, temperature tolerance, enzyme sensitivity, metabolism of carbohydrates, enzymatic activities and antimicrobial activity against S. mutans UKMCC 1019 and C. albicans UKMCC 3001 by well diffusion assay. The effect of CCFS on cell structure of S. mutans UKMCC 1019 was observed under transmission electron microscopy (TEM). RESULTS: The CCFS from isolate CC2 from Kimchi showed the highest inhibition against S. mutans UKMCC 1019, which was 76.46 % or 4406.08 mm2/mL and it was identified to be most closely related to Enterococcus faecium DSM 20477 based on 16 s rRNA sequencing. The CCFS of E. faecium DSM 20477 had high tolerance to acidic and alkaline environment as well as high temperature. It also shows high antifungal activities against C. albicans UKMCC 3001 with 2362.56 mm2/mL. Under TEM, the cell walls and the cytoplasm membrane of S. mutans UKMCC 1019 were disrupted by the antimicrobial substance, causing cell lysis. CONCLUSIONS: Hence, the CCFS from E. faecium DSM 20477 is a potential bacteriocin in future for the treatment of dental caries.

Non-verbal speech cues as objective measures for negative symptoms in patients with schizophrenia.

Negative symptoms in schizophrenia are associated with significant burden and possess little to no robust treatments in clinical practice today. One key obstacle impeding the development of better treatment methods is the lack of an objective measure. Since negative symptoms almost always adversely affect speech production in patients, speech dysfunction have been considered as a viable objective measure. However, researchers have mostly focused on the verbal aspects of speech, with scant attention to the non-verbal cues in speech. In this paper, we have explored non-verbal speech cues as objective measures of negative symptoms of schizophrenia. We collected an interview corpus of 54 subjects with schizophrenia and 26 healthy controls. In order to validate the non-verbal speech cues, we computed the correlation between these cues and the NSA-16 ratings assigned by expert clinicians. Significant correlations were obtained between these non-verbal speech cues and certain NSA indicators. For instance, the correlation between Turn Duration and Restricted Speech is -0.5, Response time and NSA Communication is 0.4, therefore indicating that poor communication is reflected in the objective measures, thus validating our claims. Moreover, certain NSA indices can be classified into observable and non-observable classes from the non-verbal speech cues by means of supervised classification methods. In particular the accuracy for Restricted speech quantity and Prolonged response time are 80% and 70% respectively. We were also able to classify healthy and patients using non-verbal speech features with 81.3% accuracy.

Nutritional optimization of Arthrospira platensis for starch and Total carbohydrates production.

Present study aims to optimize the production of starch and total carbohydrates from Arthrospira platensis. Growing concerns toward unprecedented environmental issues associated with plastic pollution has created a tremendous impetus to develop new biomaterials for the production of bioplastic. Starch-based biopolymers from algae serve as sustainable feedstock for thermoplastic starch production due to their abundant availability and low cost. A. platensis was cultivated in Zarrouk's medium at 32 ± 1°C and exposed to red light with a photoperiod of 12:12 hr light/dark. Growth kinetics studies showed that the maximum specific growth rate (µmax ) obtained was 0.059 day-1 with the doubling time (td ) of 11.748 days. Subsequently, Zarrouk's medium with different concentrations of sulfur, phosphorus and nitrogen was prepared to establish the nutrient-limiting conditions to enhance the accumulation of starch and total carbohydrates. In this study, the highest starch accumulated was 6.406 ± 0.622 mg L-1 under optimized phosphorus limitation (0.025 g L-1 ) conditions. Nitrogen limitation (0.250 g L-1 ) results demonstrated significant influenced (p < 0.05) on total carbohydrates (67.573 ± 2.893 mg L-1 ) accumulation in A. platensis. The starch accumulation in A. platensis was significantly affected (p < 0.05) by phosphorus limitation (0.0025 g L-1 ). Subsequently, the optimized phosphorus concentration was coupled with mixotrophic cultivation to further enhance the starch accumulation. The results obtained indicated that, the starch (11.426 ± 0.314 mg L-1 ) and carbohydrates (43.053 ± 2.986 mg L-1 ) concentration obtained was significantly high (p < 0.05) under mixotrophic cultivation. Therefore, it shown that nutrient limitation and mixotrophic cultivation are viable strategies to enhance the accumulation of starch and total carbohydrates in A. platensis.

Comprehensive studies on optimization of cellulase and xylanase production by a local indigenous fungus strain via solid state fermentation using oil palm frond as substrate.

The high cost of cellulases remains the most significant barrier to the economical production of bio-ethanol from lignocellulosic biomass. The goal of this study was to optimize cellulases and xylanase production by a local indigenous fungus strain (Aspergillus niger DWA8) using agricultural waste (oil palm frond [OPF]) as substrate. The enzyme production profile before optimization indicated that the highest carboxymethyl cellulose (CMCase), filter paper (FPase), and xylanase activities of 1.06 U/g, 2.55 U/g, and 2.93 U/g were obtained on day 5, day 4, and day 5 of fermentation, respectively. Response surface methodology was used to study the effects of several key process parameters in order to optimize cellulase production. Of the five physical and two chemical factors tested, only moisture content of 75% (w/w) and substrate amount of 2.5 g had statistically significant effect on enzymes production. Under optimized conditions of 2.5 g of substrate, 75% (w/w) moisture content, initial medium of pH 4.5, 1 × 106 spores/mL of inoculum, and incubation at ambient temperature (±30°C) without additional carbon and nitrogen, the highest CMCase, FPase, and xylanase activities obtained were 2.38 U/g, 2.47 U/g, and 5.23 U/g, respectively. Thus, the optimization process increased CMCase and xylanase production by 124.5 and 78.5%, respectively. Moreover, A. niger DWA8 produced reasonably good cellulase and xylanase titers using OPF as the substrate when compared with previous researcher finding. The enzymes produced by this process could be further use to hydrolyze biomass to generate reducing sugars, which are the feedstock for bioethanol production.

Optimization of polyhydroxyalkanoate (PHA) production by Burkholderia cepacia BPT1213 utilizing waste glycerol as the sole carbon source

@#Aims:This study was carried out to optimize the fermentation conditions using statistical approach for polyhydroxyalkanoate(PHA) production by a local isolate, Burkholderia cepaciaBPT1213, in the shake flask system.Methodology and results:Throughout this study, B. cepaciaBPT1213 was grown in minimal salt medium (MSM) supplemented with 2% of waste glycerol (86.70% purity).The strain can produce up to 1.33 g/L cell dry weight (CDW) with 22.21% of PHA content, thus giving a total PHA concentration 0.30 g/L before optimization. A factorial design experiment that was carried out showed all parameters KH2PO4, Na2HPO4·2H2O, carbon-to-nitrogen ratio (C/N), initial pH of medium, and temperature significantly affected the growth (cell dry weight, CDW) and PHA content. Response surface methodology (RSM) using central composite design (CCD) was then applied to optimize these parameters. The optimum conditions suggested were at 2.5 g/L KH2PO4, 4.5 g/L Na2HPO4·2H2O, 30 (g/g) C/N ratio, initial medium pH of 8.5 and 37 °C cultivation temperature, with a predicted CDW of 3.43 g/L and PHA content of 45.71% contributing to 1.57 g/L total PHA concentration. The verification experiment resulted in 3.60 g/L of CDW with 48.08% of PHA content contributing to 1.73 g/L total PHA concentration.Conclusion, significance and impact of study:The statistical approach using factorial design and RSM have succeeded in increasing the production of PHA by B. cepaciaBPT1213 using waste glycerol as the sole carbon source which is a promising renewable and cheaper feedsto

Proximate and biochemical analysis for marine and freshwater algae

@#Aims:In this study, ten indigenous microalgae samples from freshwater and marine waters from Malaysia, cultured and analysed on proximate and biochemical analysis. The proximate and biochemical analysis consists of starch, carbohydrates, lipid, protein, ash and moisture contents. This study was more focused on screening of starch accumulation in marine and freshwater microalgae cultures. Methodology and results:Based on screening, the results showed that Chlorella salinacontents highest starch of 4.92±0.33%, followed by Spirulinasp. 2.58±1.18%, Isochrysis maritime 0.99±0.33%, and lastly for Nitzschiapanduriformisand Naviculadistanscontents similar percentage of starch (0.44±0.10 and 0.40±0.07%, respectively). Besides starch analysis, proximate analyses(ash, moisture, lipid, protein, and carbohydrates) have been conducted. The results obtained indicated that all the cultures contain more than 4.50% of carbohydrates in average, followed by lipid and protein <1%. The results demonstrate that further optimization and various harvesting stages (early of exponential phase, early of stationary phaseand late stationary phase) may increase lipid, carbohydrates, starch, and protein accumulation. Chlorella salinaand Spirulinasp. will be used to further study on optimization of physical and chemical factors for high starch accumulation. Conclusion, significance and impact of study:In conclusion, this experiment focused more on preliminary screening for further application of starch uses in food and food packaging indust

Optimization of bioethanol production process using oil palm frond juice as substrate

Aims: Bioethanol is an environmental friendly energy source with a lot of great prospective and become an alternative to fossil fuels .Oil palm frond juice (OPFJ) is a potential sources of sugars for bioethanol production. The present study aimed to optimize bioethanol production. Methodology and results: Bioethanol fermentation was carried out by Saccharomyces cerevisiae HC10 using OPFJ as substrate in bioreactor with 1.5 L working volume. Growth profile was performed for 42 h with sampling every 3 h interval. Effect of agitation speed (rpm) and volume of OPFJ were screened to select significant factor for high production of bioethanol. Agitation speed at 175 rpm and volume of oil OPFJ; 40% gave 5.25 g/L and 4.52 g/L of ethanol and biomass concentration, respectively. These parameters were further investigated via central composite design (CCD) of Response Surface Methodology (RSM) to maximize bioethanol production. The suggested optimum conditions for bioethanol production were agitation speed at 152 rpm and volume of OPFJ at 39.71% in which giving ethanol concentration of 4.79 g/L. Growth profile after optimization indicated that the highest ethanol concentration (5.75%) was achieved after 15 h of fermentation. Kinetic studies indicated that ethanol yield coefficient (Yp/s) due to consumption of OPFJ and productivity of ethanol was 3.5 fold and 25% increased compared to before optimization, respectively. While, in term of ethanol yield about 9% increased was observed. Conclusion, Significance and Impact of study: This showed that OPFJ can be an alternative new feedstock for bioethanol production using S. cerevisiae HC10.

Enhancement of cellulolytic enzymes and xylanase production via classical mutational techniques under solid-state fermentation condition

Aims: High cost of cellulases remains the most significant barrier to the economical production of bio-ethanol from lignocellulosic biomass (LB). The present study aims at developing a local cellulolytic fungal strain through random mutagenesis coupled with the feasibility of solid-state fermentation (SSF) by utilizing agricultural wastes such as oil palm frond (OPF) as the substrate. Methodology and results: Out of 95 wild isolates tested, native fungal strain Aspergillus niger, designated DWA8 was isolated as the top enzymatic secretor. For quantitative enzyme analysis, SSF was conducted using 1x106 spore/mL inoculated onto 5 g of ground OPF, incubated at room temperature for 7 days, with 70% moisture content and an initial medium pH of 7. Random mutagenesis has always been tempting in the enhancement of enzyme production. In this work, the compounded treatment of microwave, ultraviolet (UVC) and Ethyl Methanesulfonate (EMS) have generated an Aspergillus niger MUE3.06 mutant with an overall increase of 114% in CMCase activity, approximately 70% in FPase and Xylanase activity respectively compared with the parental DWA8 strain. Thus this finding is capable to be fully developed as an established mutational scheme to create highly productive filamentous fungus in a cheap, simple and sustainable way. Conclusion, significance and impact of study: It was the first attempt to explore the combine effect of the three popular mutagens upon cellulases and xylanases. It is believed that more diversified of mutagen types induce more diversified mutation pattern (with instructive planning), which is very desirable in creating new enzymes with novel abilities.