Shoulder Movement-Centered Measurement and Estimation Scheme for Underarm-Throwing Motions.

Underarm throwing motions are crucial in various sports, including boccia. Unlike healthy players, people with profound weakness, spasticity, athetosis, or deformity in the upper limbs may struggle or find it difficult to control their hands to hold or release a ball using their fingers at the proper timing. To help them, our study aims to understand underarm throwing motions. We start by defining the throwing intention in terms of the launch angle of a ball, which goes hand-in-hand with the timing for releasing the ball. Then, an appropriate part of the body is determined in order to estimate ball-throwing intention based on the swinging motion. Furthermore, the geometric relationship between the movements of the body part and the release angle is investigated by involving multiple subjects. Based on the confirmed correlation, a calibration-and-estimation model that considers individual differences is proposed. The proposed model consists of calibration and estimation modules. To begin, as the calibration module is performed, individual prediction states for each subject are updated online. Then, in the estimation module, the throwing intention is estimated employing the updated prediction. To verify the effectiveness of the model, extensive experiments were conducted with seven subjects. In detail, two evaluation directions were set: (1) how many balls need to be thrown in advance to achieve sufficient accuracy; and (2) whether the model can reach sufficient accuracy despite individual differences. From the evaluation tests, by throwing 20 balls in advance, the model could account for individual differences in the throwing estimation. Consequently, the effectiveness of the model was confirmed when focusing on the movements of the shoulder in the human body during underarm throwing. In the near future, we expect the model to expand the means of supporting disabled people with ball-throwing disabilities.

Peripheral Microneedle Patch for First-Aid Hemostasis.

Despite the minimized puncture sizes and high efficiency, microneedle (MN) patches have not been used to inject hemostatic drugs into bleeding wounds because they easily destroy capillaries when a tissue is pierced. In this study, a shelf-stable dissolving MN patch is developed to prevent rebleeding during an emergency treatment. A minimally and site-selectively invasive hemostatic drug delivery system is established by using a peripheral MN (p-MN) patch that does not directly intrude the wound site but enables topical drug absorption in the damaged capillaries. The invasiveness of MNs is histologically examined by using a bleeding liver of a Sprague-Dawley (SD) rat as an extreme wound model in vivo. The skin penetration force is quantified to demonstrate that the administration of the p-MN patch is milder than that of the conventional MN patch. Hemostatic performance is systematically studied by analyzing bleeding weight and time and comparing them with that of conventional hemostasis methods. The superior performance of a p-MN for the heparin-pretreated SD rat model is demonstrated by intravenous injection in vivo.

Application of flexible pin for planetary gear set of wind turbine gearbox.

Wind turbines are eco-friendly energy sources that generate electricity from wind power. Among their various components, gearboxes constitute the most critical loss owing to their longest downtime. To guarantee their durability, a flexible pin was designed based on the original straddle-mounted pin for enhanced tooth load sharing and distribution in the planetary gear set (PGS) of a wind turbine gearbox (WTGB). The improved durability was evaluated by calculating the mesh load factor and face load factor for contact stress and comparing these values with those of the original straddle-mounted pin. The mesh load factor decreased from 1.37 to 1.08, whereas the maximum face load factor decreased slightly, moderating the overall safety factor variation. Furthermore, the structure of the proposed flexible pin model was analyzed and verified that no static failure or interference occurred. Additionally, microgeometry optimization was applied to improve the load distribution. Therefore, it was verified that a flexible pin applied to a single helical-geared PGS, thus far considered impossible, enhances the durability of WTGBs by improving the load sharing and distribution of a PGS. Consequently, the possibility of designing single helical-geared planetary gearboxes with flexible pins to take advantages of both helical gears and flexible pins was shown analytically.

A Study on Real Time IGBT Junction Temperature Estimation Using the NTC and Calculation of Power Losses in the Automotive Inverter System.

This paper proposes a junction temperature estimation algorithm for the insulated gate bipolar transistor (IGBT) based on a power loss calculation and a thermal impedance model for inverter systems. The Simulink model was designed to calculate the power losses of power semiconductor devices and to estimate the junction temperature with a simplified thermal impedance model. This model can estimate the junction temperature up to the transient state, including the steady state. The parameters used to calculate the power losses, the thermal resistance, and the thermal capacitance were optimized for a given inverter to be tested for improving the accuracy. The simulation results and experimental measurement data were compared to verify the proposed junction temperature estimation algorithm. Finally, the algorithm was installed on the inverter controller, and the performance was verified by comparing the real time estimation result with the measured temperature.

D-dimer levels and cerebral infarction in critically ill cancer patients.

BACKGROUND: D-dimer levels have been used in the diagnosis of a variety of thrombosis-related diseases. In this study, we evaluated whether measuring D-dimer levels can help to diagnose cerebral infarction (CI) in critically ill cancer patients. METHODS: We retrospectively evaluated all cancer patients who underwent brain magnetic resonance imaging (MRI) between March 2010 and February 2014 at the medical oncology intensive care unit (ICU) of Samsung Medical Center. Brain MRI scanning was performed when CI was suspected due to acute neurological deficits. We compared D-dimer levels between patients ultimately diagnosed as having or not having CI and analyzed diffusion-weighted imaging (DWI) lesion patterns. RESULTS: A total of 88 patients underwent brain MRI scanning due to clinical suspicion of CI; altered mental status and unilateral hemiparesis were the most common neurological deficits. CI was ultimately diagnosed in 43 (49%) patients. According to the DWI patterns, multiple arterial infarctions (40%) were more common than single arterial infarctions (9%). Cryptogenic stroke etiologies were more common (63%) than determined etiologies. There was no significant difference in D-dimer levels between patients with and without CI (P = 0.319). Although D-dimer levels were not helpful in diagnosing CI, D-dimer levels were associated with cryptogenic etiologies in critically ill cancer patients; D-dimer levels were higher in the cryptogenic etiology group than in the determined etiology group or the non-infarction group (P = 0.001). In multivariate analysis, elevated D-dimer levels (> 8.89 µg/mL) were only associated with cryptogenic stroke (adjusted OR 5.46; 95% confidence interval, 1.876-15.857). CONCLUSIONS: Abnormal D-dimer levels may support the diagnosis of cryptogenic stroke in critically ill cancer patients.

mvp - an open-source preprocessor for cleaning duplicate records and missing values in mass spectrometry data.

Mass spectrometry (MS) data are used to analyze biological phenomena based on chemical species. However, these data often contain unexpected duplicate records and missing values due to technical or biological factors. These 'dirty data' problems increase the difficulty of performing MS analyses because they lead to performance degradation when statistical or machine-learning tests are applied to the data. Thus, we have developed missing values preprocessor (mvp), an open-source software for preprocessing data that might include duplicate records and missing values. mvp uses the property of MS data in which identical chemical species present the same or similar values for key identifiers, such as the mass-to-charge ratio and intensity signal, and forms cliques via graph theory to process dirty data. We evaluated the validity of the mvp process via quantitative and qualitative analyses and compared the results from a statistical test that analyzed the original and mvp-applied data. This analysis showed that using mvp reduces problems associated with duplicate records and missing values. We also examined the effects of using unprocessed data in statistical tests and examined the improved statistical test results obtained with data preprocessed using mvp.

Polymerization shrinkage, flexural and compression properties of low-shrinkage dental resin composites.

This study evaluated the polymerization shrinkage, flexural and compressive properties of low-shrinkage resin composites. For the study, four methacrylate-based and one silorane-based resin composites were light cured using three different light-curing units (LCUs) and their polymerization shrinkage, flexural (strength (FS) and modulus (FM)) and compressive (strength (CS) and modulus (CM)) properties were evaluated. Data were statistically analyzed using ANOVA and a post-hoc Tukey test. The polymerization shrinkage ranged approximately 7.6-14.2 µm for 2-mm thick specimens depending on the resin product and LCU. Filtek LS showed the least shrinkage while the rest shrank approximately 13.2-14.2 µm. However, Filtek LS showed the greatest shrinkage difference for the used LCUs. FS and CS of the tested specimens ranged 96.2-152.1 MPa and 239.2-288.4 MPa, respectively, depending on the resin product and LCU. The highest and lowest FS and FM were recorded for the methacrylate-based resin composites. Among the specimens, Filtek LS showed the lowest CS and CM.

Skin temperature changes in patients with unilateral lumbosacral radiculopathy.

OBJECTIVE: To clarify the relationship of skin temperature changes to clinical, radiologic, and electrophysiological findings in unilateral lumbosacral radiculopathy and to delineate the possible temperature-change mechanisms involved. METHODS: One hundred and one patients who had clinical symptoms and for whom there were physical findings suggestive or indicative of unilateral lumbosacral radiculopathy, along with 27 normal controls, were selected for the study, and the thermal-pattern results of digital infrared thermographic imaging (DITI) performed on the back and lower extremities were analyzed. Local temperatures were assessed by comparing the mean temperature differences (ΔT) in 30 regions of interest (ROIs), and abnormal thermal patterns were divided into seven regions. To aid the diagnosis of radiculopathy, magnetic resonance imaging (MRI) and electrophysiological tests were also carried out. RESULTS: The incidence of disc herniation on MRI was 86%; 43% of patients showed electrophysiological abnormalities. On DITI, 97% of the patients showed abnormal ΔT in at least one of the 30 ROIs, and 79% showed hypothermia on the involved side. Seventy-eight percent of the patients also showed abnormal thermal patterns in at least one of the seven regions. Patients who had motor weakness or lateral-type disc herniation showed some correlations with abnormal DITI findings. However, neither pain severity nor other physical or electrophysiological findings were related to the DITI findings. CONCLUSION: Skin temperature change following lumbosacral radiculopathy was related to some clinical and MRI findings, suggesting muscle atrophy. DITI, despite its limitations, might be useful as a complementary tool in the diagnosis of unilateral lumbosacral radiculopathy.

Effect of energy density on low-shrinkage composite resins: diode-pumped solid state laser versus quartz-tungsten-halogen light-curing unit.

OBJECTIVE: The purpose of the present study was to evaluate the effect of energy density on the polymerization of low-shrinkage composite resins. BACKGROUND DATA: The number of photons needs to initiate the polymerization process can be controlled by light intensity and curing time through the form of energy density. MATERIALS AND METHODS: For the study, two methacrylate-based (Premise [PR] and Venus Diamond [VE]) and one silorane-based (Filtek LS [LS]) composite resins were light cured using a quartz-tungsten-halogen (QTH) light-curing unit (LCU) and a 473 nm diode-pumped solid state (DPSS) laser. Degree of conversion (DC), microhardness, refractive index, and polymerization shrinkage were evaluated under different energy densities. Through the study, the feasibility of DPSS laser as a light source was tested as well. RESULTS: LS showed the highest DC and refractive index both on the top and bottom surfaces, and the least polymerization shrinkage among the tested specimens. For the same or similar energy density, QTH and DPSS showed insignificant DC difference (p>0.05). On the other hand, for microhardness, except for one case at the bottom surface, QTH and DPSS showed significant difference (p<0.001). DPSS generated slightly lower polymerization shrinkage than that by QTH. CONCLUSIONS: DC, microhardness, refractive index, and polymerization shrinkage were linearly correlated with energy density. In most cases, there was a strong linear correlation among DC, mirohardness, and refractive index. The DPSS laser of 473 nm could polymerize low-shrinkage composite resins to the level that was achieved by the conventional QTH unit.

The relationship between hippocampal volume and cognition in patients with chronic primary insomnia.

BACKGROUND AND PURPOSE: Differences in hippocampal volume (HV) were compared between chronic primary insomniacs (PIs) and good sleepers (GSs), and the relationship between HV and memory function in PIs was investigated to clarify the effect of chronic sleep deprivation on brain structure and cognition. METHODS: Twenty PIs (mean age, 50 years; 18 females) and 20 age-, gender-, and education-matched GSs were enrolled. Brain magnetic resonance imaging (MRI) was performed on a 1.5-T MRI scanner. Left and right HV and intracranial volume (ICV) were measured manually. Nighttime polysomnography and neuropsychological testing were also applied to all subjects. Group differences in HV were analyzed and the relationships between HV and sleep questionnaire data, nighttime polysomnography, and neuropsychological findings were evaluated. RESULTS: Compared to GSs, PIs exhibited significantly increased sleep latency and arousal index and a decreased percentage of REM sleep in nighttime polysomnography, as well as impaired verbal and visual memory, and frontal lobe function. Absolute HV and ICV did not differ significantly between PIs and GSs. In the PIs, right and left HVs were negatively correlated with the duration of insomnia and the arousal index, and positively correlated with the recognition of visual memory. In addition, free recall in verbal memory was positively correlated with left HV in PIs. CONCLUSIONS: These findings suggest that chronic sleep deprivation impairs memory and frontal lobe function, and that a long duration of insomnia and poor sleep quality contribute to a bilateral reduction in HV.

Factors contributing to Korean teachers' attitudes toward students with epilepsy.

We investigated factors contributing to teachers' attitudes toward students with epilepsy. Data were collected from 604 teachers in Korea. The questionnaire included the Scale of Attitudes Toward Persons with Epilepsy (ATPE) and a demographic and teaching experience survey. In stepwise linear regression analysis, ATPE Knowledge scores (P<0.001) and prior experience teaching a student with epilepsy (P=0.001) were identified as significant factors for ATPE Attitude scores. The ATPE Knowledge scores accounted for 50.1% of the variance in the Attitude scores, and experience teaching a student with epilepsy accounted only for 1.0%. Our finding that teachers' knowledge is the most important factor influencing teacher's attitudes toward epilepsy indicates that teachers should be provided with information about epilepsy universally, across geographic settings, educational levels, and experience levels.

Factors contributing to Korean adolescents' perceptions of stigma with respect to epilepsy.

We assessed knowledge and perceptions of epilepsy held by Korean adolescents in the general population, and investigated factors important in adolescents' perceptions of stigma with respect to epilepsy. Surveys were distributed to students at 22 schools. A total of 1377 students participated. Fewer than half of all students (45.1%) reported hearing or reading about epilepsy. Overall, students showed a general lack of familiarity with and knowledge of epilepsy. Stigma perception scores were significantly higher in boys than in girls (P<0.05) and in middle school than in high school (P<0.05) students. We also found that stigma perception scores were significantly correlated with both younger age (r=-0.074, P=0.006) and lower knowledge scores (r=-0.404, P=0.000). Linear regression analysis showed that stigma-related perception was associated with lower knowledge scores (P<0.001) and middle school (P<0.05). These results indicate a need for public education of adolescents in the general population to decrease the stigma associated with epilepsy.