Naturally diffused sintering aid for highly conductive bilayer electrolytes in solid oxide cells.

Solid oxide cells (SOCs) are promising sustainable and efficient electrochemical energy conversion devices. The application of a bilayer electrolyte comprising wide electrolytic oxide and highly conductive oxide is essential to lower the operating temperatures while maintaining high performance. However, a structurally and chemically ideal bilayer has been unattainable through cost-effective conventional ceramic processes. Here, we describe a strategy of naturally diffused sintering aid allowing the fabrication of defect-free doped-zirconia/doped-ceria bilayer electrolyte with full density and reduced interdiffusion layer at lower sintering temperature owing to the supply of small but appropriate amount of sintering aid from doped zirconia to doped ceria that makes the thermal shrinkages of both layers perfectly congruent. The resulting SOCs exhibit a minimal ohmic loss of 0.09 ohm cm2 and remarkable performances in both fuel cell (power density exceeding 1.3 W cm−2) and electrolysis (current density of −1.27 A cm−2 at 1.3 V) operations at 700°C.

Decrease in Skin Prion-Seeding Activity of Prion-Infected Mice Treated with a Compound Against Human and Animal Prions: a First Possible Biomarker for Prion Therapeutics.

Previous studies have revealed that the infectious scrapie isoform of prion protein (PrPSc) harbored in the skin tissue of patients or animals with prion diseases can be amplified and detected through the serial protein misfolding cyclic amplification (sPMCA) or real-time quaking-induced conversion (RT-QuIC) assays. These findings suggest that skin PrPSc-seeding activity may serve as a biomarker for the diagnosis of prion diseases; however, its utility as a biomarker for prion therapeutics remains largely unknown. Cellulose ethers (CEs, such as TC-5RW), widely used as food and pharmaceutical additives, have recently been shown to prolong the lifespan of prion-infected mice and hamsters. Here we report that in transgenic (Tg) mice expressing hamster cellular prion protein (PrPC) infected with the 263K prion, the prion-seeding activity becomes undetectable in the skin tissues of TC-5RW-treated Tg mice by both sPMCA and RT-QuIC assays, whereas such prion-seeding activity is readily detectable in the skin of untreated mice. Notably, TC-5RW exhibits an inhibitory effect on the in vitro amplification of PrPSc in both skin and brain tissues by sPMCA and RT-QuIC. Moreover, we reveal that TC-5RW is able to directly decrease protease-resistant PrPSc and inhibit the seeding activity of PrPSc from chronic wasting disease and various human prion diseases. Our results suggest that the level of prion-seeding activity in the skin may serve as a useful biomarker for assessing the therapeutic efficacy of compounds in a clinical trial of prion diseases and that TC-5RW may have the potential for the prevention/treatment of human prion diseases.

Open-cell voltage and electrical conductivity of a protonic ceramic electrolyte under two chemical potential gradients.

BaZr0.8Y0.2O3-δ, which is a proton-conducting oxide used as an electrolyte for protonic ceramic fuel cells (PCFCs), possesses two mobile ionic charge carriers-oxygen ions and protons-in a crystalline lattice below 500 °C. The equilibrium concentrations of these charge carriers are dependent on water activity. This feature induces a complexity in the distribution of charge carriers within the electrolyte under the influence of the two chemical potential gradients of oxygen and water, which is a typical operating condition in PCFCs. This makes the theoretical derivations of the open-cell voltage and the electrical resistance of the electrolyte difficult. Here, we calculate the distributions of oxygen vacancies and protons across the electrolyte by solving diffusion equations based on the defect chemistry of BaZr0.8Y0.2O3-δ at 500 °C. We then extract the theoretical open-cell voltage and electrical conductivity of the electrolyte in a range of water and oxygen activities that is of interest for PCFCs.

Identification of an Actual Strain-Induced Effect on Fast Ion Conduction in a Thin-Film Electrolyte.

Strain-induced fast ion conduction has been a research area of interest for nanoscale energy conversion and storage systems. However, because of significant discrepancies in the interpretation of strain effects, there remains a lack of understanding of how fast ionic transport can be achieved by strain effects and how strain can be controlled in a nanoscale system. In this study, we investigated strain effects on the ionic conductivity of Gd0.2Ce0.8O1.9-δ (100) thin films under well controlled experimental conditions, in which errors due to the external environment could not intervene during the conductivity measurement. In order to avoid any interference from perpendicular-to-surface defects, such as grain boundaries, the ionic conductivity was measured in the out-of-plane direction by electrochemical impedance spectroscopy analysis. With varying film thickness, we found that a thicker film has a lower activation energy of ionic conduction. In addition, careful strain analysis using both reciprocal space mapping and strain mapping in transmission electron microscopy shows that a thicker film has a higher tensile strain than a thinner film. Furthermore, the tensile strain of thicker film was mostly developed near a grain boundary, which indicates that intrinsic strain is dominant rather than epitaxial or thermal strain during thin-film deposition and growth via the Volmer-Weber (island) growth mode.

Constrained Sintering in Fabrication of Solid Oxide Fuel Cells.

Solid oxide fuel cells (SOFCs) are inevitably affected by the tensile stress field imposed by the rigid substrate during constrained sintering, which strongly affects microstructural evolution and flaw generation in the fabrication process and subsequent operation. In the case of sintering a composite cathode, one component acts as a continuous matrix phase while the other acts as a dispersed phase depending upon the initial composition and packing structure. The clustering of dispersed particles in the matrix has significant effects on the final microstructure, and strong rigidity of the clusters covering the entire cathode volume is desirable to obtain stable pore structure. The local constraints developed around the dispersed particles and their clusters effectively suppress generation of major process flaws, and microstructural features such as triple phase boundary and porosity could be readily controlled by adjusting the content and size of the dispersed particles. However, in the fabrication of the dense electrolyte layer via the chemical solution deposition route using slow-sintering nanoparticles dispersed in a sol matrix, the rigidity of the cluster should be minimized for the fine matrix to continuously densify, and special care should be taken in selecting the size of the dispersed particles to optimize the thermodynamic stability criteria of the grain size and film thickness. The principles of constrained sintering presented in this paper could be used as basic guidelines for realizing the ideal microstructure of SOFCs.

Effect of alumina nanofiller on properties of heat-treated glass composite sealants.

Alkali/alkaline-earth borosilicate glass-alumina composites containing 10 vol% Al2O3 were prepared for use as solid oxide fuel cell sealants. The effect of heat treatment and Al2O3, addition on the viscosities and electrical conductivities was investigated to improve cyclic sealing performance. Upon a 48-h heat treatment, the viscosity of the glass-alumina composites at 750 degrees C was approximately four orders of magnitude higher than that of the base glass owing to the crystallization of the glass in the presence of Al2O3. Heat treatment increased the electrical conductivities of both the base glass and the glass-alumina composites. The electrical conductivities of glass-alumina composites in the range from 400 degrees C to 550 degrees C were three times higher than those of the base glass regardless of heat treatment. This increase in the conductivities and viscosities by heat treatment was attributed to the devitrification and structural densification of the sealing glass and the partial dissolution of the Al2O3 filler in alkali/alkaline-earth borosilicate sealing glass.

Extremely thin bilayer electrolyte for solid oxide fuel cells (SOFCs) fabricated by chemical solution deposition (CSD).

An extremely thin bilayer electrolyte consisting of yttria-stabilized zirconia (YSZ) and gadolinia-doped ceria (GDC) is successfully fabricated on a sintered NiO-YSZ substrate. Major processing flaws are effectively eliminated by applying local constraints to YSZ nanoparticles, and excellent open circuit voltage and cell performance are demonstrated in a solid oxide fuel cell (SOFC) at intermediate operating temperatures.

A comparative study of catalytic partial oxidation of methane over CeO2 supported metallic catalysts.

In the present study, the catalytic partial oxidation of methane (CPOM) over various active metals supported on CeO2 (M/CeO2, M = Ir, Ni, Pd, Pt, Rh and Ru) has been investigated. The catalysts were characterized by X-ray diffraction (XRD), BET surface area, H2-temperature programmed reduction (H2-TPR), CO chemisorption and transmission electron microscope (TEM) analysis. Ir/CeO2 catalysts showed higher BET surface area, higher metal dispersion, small active metal nano-particles (approximately 3 nm) than compared to other M/CeO2 catalysts. The catalytic tests were carried out in a fixed R(mix) ratio of 2 (CH4/O2) in a fixed-bed reactor, operating isothermally at atmospheric pressure. From time-on-stream analysis at 700 degrees C for 12 h, a high and stable catalytic activity has been observed for Ir/CeO2 catalysts. TEM analysis of the spent catalysts showed that the decrease in the catalytic activity of Ni/CeO2 and Pd/CeO2 catalysts is due to carbon formation whereas no carbon formation has been observed for Ir/CeO2 catalysts.

'Illusional' nano-size effect due to artifacts of in-plane conductivity measurements of ultra-thin films.

The nano-size effect, which indicates a drastic increase in conductivity in solid electrolyte materials of nano-scale microstructures, has drawn substantial attention in various research fields including in the field of solid oxide fuel cells (SOFCs). However, especially in the cases of the conductivity of ultra-thin films measured in an in-plane configuration, it is highly possible that the 'apparent' conductivity increase originates from electrical current flowing through other conduction paths than the thin film. As a systematic study to interrogate those measurement artifacts, we report various sources of electrical current leaks regarding in-plane conductivity measurements, specifically insulators in the measurement set-up. We have observed a 'great conductivity increase' up to an order of magnitude at a very thin thickness of a single layer yttria-stabilized zirconia (YSZ) film in a set-up with an intentional artifact current flow source. Here we propose that the nano-size effect, reported to appear in ultra-thin single layer YSZ, can be a result of misinterpretation.

Effect of composition on thermal conductivity of silica insulation media.

Nano-sized fumed silica-based insulation media were prepared by adding TiO2 powders and ceramic fibers as opacifiers and structural integrity improvers, respectively. The high temperature thermal conductivities of the fumed silica-based insulation media were investigated using different types of TiO2 opacifier and by varying its content. The opacifying effects of nanostructured TiO2 powders produced by homogeneous precipitation process at low temperatures (HPPLT) were compared with those of commercial TiO2 powder. The nanostructured HPPLT TiO2 powder with a mean particle size of 1.8 microm was more effective to reduce radiative heat transfer than the commercial one with a similar mean particle size. The insulation samples with the HPPLT TiO2 powder showed about 46% lower thermal conductivity at temperatures of about 820 degrees C than those with the commercial one. This interesting result might be due to the more effective radiation scattering efficiency of the nanostructured HPPLT TiO2 powder which has better gap filling and coating capability in nano-sized composite compacts.

Electrothermal properties of porous ceramic fiber media containing carbon materials.

Electrically regenerable porous ceramic fiber media containing nanoporous carbon from 2.5% to 19.2% have been prepared for adsorption/regeneration system. An experimental apparatus was built for in situ measurement of the sample weight during adsorption and electrothermal desorption of gaseous adsorbates. Adsorption and electrothermal desorption behavior of gaseous adsorbates on carbon contained porous ceramic fiber media was explained by physical and electrothermal properties of these materials measured in this work. In situ thermal desorption and adsorption experiments show that a considerable amount of water vapor is adsorbed on the carbon contained media exposed to ambient air.