Volumetric Analysis of Peri-implant Tissue Change Over Time: Validating an Innovative 3D Method.

PURPOSE: To validate an innovative 3D volumetric method of evaluating tissue changes proposed by Lee et al in 2020 by comparing the results of this method-in which the scanned peri-implant surfaces were transformed, visualized, and analyzed as 3D objects-to the results reported by an existing method based on calculation of the mean distance between measured surfaces. The null hypothesis was that there was no statistically significant difference between the two methods. Additionally, the present study evaluated peri-implant tissue changes 5 years after single implant placement in the esthetic zone. MATERIALS AND METHODS: Both methods were applied to 11 oral implant site casts (6 maxillary central incisor sites, 5 maxillary lateral incisor sites) taken from 11 patients at crown placement and at follow-up examinations 5 years later. The methods are based on digital workflows in which the reference and 5-year casts are scanned and the resulting STL files are superimposed and analyzed for three regions of interest (mesial papilla, central area, and distal papilla). The volumetric changes reported by the Lee et al method and the mean distance method were calculated and compared using the Spearman rank correlation coefficient (P < .01) and the Wilcoxon signed-rank test (P < .05). RESULTS: The correlation between the two sets of measurements was very high (Spearman rank correlation coefficient = 0.885). The new volumetric method indicated a mean volume loss of 2.82 mm3 (SD: 5.06), while the method based on the measurement of mean distance showed a mean volume loss of 2.92 mm3 (SD: 4.43; Wilcoxon signed-rank test result: P = .77). No statistically significant difference was found. The two methods gave equivalent results, and the null hypothesis was accepted. CONCLUSIONS: The new volumetric method was validated and can be considered a trustworthy tool.

Influence of postprinting cleaning methods on the cleaning efficiency and surface and mechanical properties of three-dimensionally printed resins.

STATEMENT OF PROBLEM: The outcome of photopolymerized 3-dimensional (3D) printing is influenced by the methods used for postprinting cleaning, yet information on postprinting cleaning is sparse. PURPOSE: The purpose of this in vitro study was to assess the cleaning efficiency and surface and mechanical properties of 3D printed resin according to postprinting cleaning methods. MATERIAL AND METHODS: Specimens were fabricated from a 3D model using resin materials (NextDent C&B MFH and DIOnavi-P. MAX) and were tested for postprinting cleaning methods for 5 minutes with isopropyl alcohol, isopropyl alcohol + ultrasonic, ethyl alcohol, ethyl alcohol + ultrasonic, and ultrasonic alone. Postpolymerization was followed for 5 minutes. The cleaning efficiency, microcomputed tomography (µCT), surface roughness, Vickers hardness, and flexural strength of the specimens were evaluated. The 1-way ANOVA test was performed after considering normality. A post hoc analysis with Bonferroni was also performed (α=.008 or.005). RESULTS: Ultrasonic in addition to cleaning solutions significantly improved the cleaning efficiency in NextDent C&B MFH specimens (P<.005), whereas ultrasonic did not affect the efficiency in DIOnavi-P. MAX specimens. No significant differences were found in surface roughness by postprinting cleaning methods in either NextDent C&B MFH or DIOnavi-P. MAX (P>.005). No significant changes in surface hardness were observed by postprinting cleaning methods (P>.008). In the NextDent C&B MFH, ethyl alcohol + ultrasonic significantly decreased the flexural strength (P<.005). There were no significant differences in the flexural strength in the DIOnavi-P. MAX (P>.005). CONCLUSIONS: Ethyl alcohol was comparable with isopropyl alcohol for use as a postprinting cleaning solution for both NextDent C&B MFH and DIOnavi-P. MAX. The addition of ultrasonic to cleaning solutions should be applied with caution. These findings suggest that different postprinting cleaning methods can be recommended depending on the 3D printed resin materials.

Influence of crown shade, translucency, and scan powder application on the trueness of intraoral scanners.

OBJECTIVES: Natural teeth and dental restorations present with various shades and levels of translucency. This study aimed to determine whether these variations in ceramic crowns and scan powder application affect the trueness of intraoral scanners. METHODS: Eight identical premade resin typodonts, each prepared for a crown on the maxillary right second molar, were used. Eight lithium disilicate crowns, distinguished by two levels of translucency (high and low) and four shades (BL1, A2, A3, and A4), were fabricated to an identical design and cemented onto each typodont, providing eight distinct experimental groups (2 levels of translucency × 4 shades). Reference scans were acquired using a desktop scanner. Test scans were performed ten times for each experimental group using two different intraoral scanners (Medit i700 and CEREC Primescan AC), with and without the application of scan powder (n = 10). Three-dimensional metrology software was used to assess the trueness of the intraoral scan datasets. Statistical analysis involved the Kruskal-Wallis H test, Mann-Whitney U test, and independent t-test (α=0.05). RESULTS: For powder-free intraoral scan datasets, the crown shade did not significantly affect trueness within each translucency group (P = 1.000). For both intraoral scanners, compared with low translucency groups, higher marked deviations were exhibited by high translucency groups (P<.001). Scan powder use largely mitigated these differences (P>.05) and enhanced the trueness of the intraoral scan (P<.01). CONCLUSIONS: Shade did not significantly influence the trueness of intraoral scans. High-translucency crowns were scanned with less accuracy than were low-translucency crowns. CLINICAL SIGNIFICANCE: Unlike tooth shade, translucency significantly affected the accuracy of intraoral scans. Therefore, considering the use of scan powder when scanning objects with high translucency may be beneficial.

Influence of limited mouth opening in children on intraoral scanning accuracy: An in vitro study.

BACKGROUND: Although intraoral scanning is highly reliable, little is known about its accuracy in young children with limited mouth-opening ability. AIM: To determine the accuracy of intraoral scans based on the degree of mouth opening. DESIGN: To simulate mouth opening in children with primary dentition, three groups (n = 5 per group) were allocated by maximum mouth opening of 30, 37 and 40 mm. After the primary dentition model was connected to a dental phantom, intraoral scanning was performed using iTero and TRIOS4. The scanned files were digitally evaluated. Root mean square values were calculated to assess trueness and precision. RESULTS: iTero showed deviations of three-dimensional trueness of 0.067 ± 0.008, 0.063 ± 0.001 and 0.065 ± 0.005 mm, and TRIOS4 of 0.07 ± 0.002, 0.064 ± 0.003 and 0.066 ± 0.002 mm in the 30, 37 and 40 mm groups, respectively. There were no significant differences in either mouth opening (p > .017) or the intraoral scanners (p > .05). The same statistical results were obtained for precision, with the exception of the 30 mm of mouth opening. CONCLUSIONS: Within the limits of this study, limited mouth opening hardly influenced the accuracy of intraoral scanning.

A comparison of maxillary posterior changes following facemask therapy: Skeletal anchorage versus tooth-borne anchorage.

OBJECTIVE: To compare changes in the maxillary posterior structure as seen in cone-beam computed tomography (CBCT) images resulting from facemask therapy using skeletal (miniplate/FM) anchorage versus tooth-borne anchorage (RME/FM). MATERIALS AND METHODS: A retrospective study was conducted on 20 patients divided into the miniplate/FM group (nine patients aged 9.5 ± 1.4 years) and the RME/FM group (11 patients aged 9.2 ± 1.4 years). CBCT images before and after facemask therapy were evaluated to assess changes in the maxillary posterior structure. RESULTS: The miniplate/FM group had greater advancement of the maxilla and midface compared to the RME/FM group (p < .05). Specifically, there was about three times more advancement of the pterygomaxillary suture in the miniplate/FM group than in the RME/FM group (p < .05). Moreover, the advancement of the pterygomaxillary suture was about half the advancement of A point in the miniplate/FM group, while only about 25% in the RME/FM group. Finally, the miniplate/FM group showed an increase in the transverse dimension of the posterior and superior parts of the maxilla (p < .05). CONCLUSION: There was greater forward movement of the pterygomaxillary suture with facemask therapy using the skeletal anchorage compared to tooth-borne anchorage, leading to a more significant advancement of the maxilla and midface.

Strength and Surface Characteristics of 3D-Printed Resin Crowns for the Primary Molars.

Some resin polymers available for three-dimensional (3D) printing are slightly elastic, which may be advantageous when used for full crown coverage of the primary teeth. This study was performed to evaluate the mechanical properties of two types of 3D-printed resin crowns in terms of strength and surface characteristics. Polymer resins used for temporary crowns (TCs) and temporary flexible dentures (TFDs) were tested. Digitally designed crowns with different thicknesses (0.4 and 0.6 mm) were 3D-printed. Milled zirconia crowns were used as the control. The static and dynamic fracture loads of the crowns were measured. The crown surface was evaluated using scanning electron microscopy. The average strength did not differ between the types of crowns. The differences between the dynamic and static fracture loads were insignificant. In the TC group, thicker crowns showed lower strength both under static and dynamic loads. After thermomechanical loading, microcracks and dropouts of macrofillers were detected on the surface of all types of resin crowns. The deposition of abraded debris occurred more in the TFD group. The 3D-printed resin crowns were thought to endure biting forces in children. However, some limitations of the material itself should be improved for consideration as a new treatment option in pediatric dentistry.

Reliability of digital repeated-scan superimposition and single-scan techniques for wear volume loss assessment on flat surfaces.

OBJECTIVES: Evidence on the reliability of digital techniques for wear volume assessment using three-dimensional (3D) scan datasets is scarce. This study evaluated the reliability of a repeated-scan superimposition technique and two single-scan techniques in assessing wear volume loss on flat surfaces of 3D-printed resin specimens. METHODS: Cuboid-shaped (15×10×10 mm) resin specimens were 3D-printed (n = 14) and scanned before and after 200,000 cycles of masticatory simulation. For the repeated-scan superimposition technique, digital 3D models of specimens before and after masticatory simulation were superimposed, and the volume loss was determined. The first single-scan technique utilized a computer-aided design freeware program, while the second one employed a 3D-metrology software program. In the freeware program, the worn area of 3D objects was edited directly to obtain a flat surface. In the 3D-metrology software program, the worn area was deleted first and then filled to the flat surface. The volume differences before and after editing were calculated in each software program. Agreement between the three measurement techniques was determined through intraclass correlation coefficients (ICCs). One-way analysis of variance was performed to compare the wear volume loss assessed by the three techniques (α = 0.05). RESULTS: High inter-technique reliability was observed between the three assessment techniques (ICC = 0.998, p < .001). On pair-wise comparisons of two of the three techniques, all pairs showed high consistency (ICC ≥ 0.999, p < .001). No significant difference was found in the wear volume loss assessed using the three techniques (p = .996). CONCLUSIONS: Digital repeated-scan superimposition and two single-scan techniques demonstrated high reliability in assessing wear volume loss on flat surfaces. CLINICAL SIGNIFICANCE: The repeated-scan superimposition technique can be effectively utilized to assess wear volume loss of anatomically shaped specimens and flat surfaces. This study indicates that the single-scan techniques may serve as a suitable alternative to the repeated-scan superimposition technique when evaluating wear volume loss of flat surfaces.

AUTONOMOUS ROBOTIC SURGERY SEEMS PROMISING AS AN ACCURATE TECHNOLOGY FOR SINGLE-TOOTH IMPLANT PLACEMENT IN THE ESTHETIC ZONE.

ARTICLE TITLE AND BIBLIOGRAPHIC INFORMATION: Yang S, Chen J, Li A, Deng K, Li P, Xu S. Accuracy of autonomous robotic surgery for single-tooth implant placement: a case series. J Dent. 2023;132:104451. doi:10.1016/j.jdent.2023.104451. Epub 2023 Feb 11. PMID: 36781099. SOURCE OF FUNDING: This case series study was supported by grants from the Guangdong Basic and Applied Basic Research Foundation, Science and Technology Projects in Guangzhou, Science Research Cultivation Program, and Clinical Research Initiation Plan of the Stomatological Hospital, Southern Medical University, China. TYPE OF STUDY/DESIGN: Case series. No a priori power calculation or pilot data. Nonconsecutive participant recruitment.

Lack of keratinized mucosa increases peri-implantitis risk.

DESIGN: A systematic appraisal and statistical aggregation of primary studies in humans. DATA SOURCES: The researchers utilized PubMed (Medline) and Scopus databases as the primary data sources for this study. They performed a comprehensive literature search based on free keywords and Medical Subject Heading (MeSH) terms to enhance the search accuracy. The database search was concluded on November 13, 2022. Furthermore, a meticulous examination of the references cited in the selected studies was conducted to identify additional relevant articles that could be incorporated into the analysis. STUDY SELECTION: The systematic review focused on partially or fully edentulous patients receiving dental implants and aimed to determine if the lack of keratinized mucosa at the implant site increased the risk of peri-implantitis compared to patients with adequate keratinized mucosa. Human studies with a minimum of 100 implants, cross-sectional, cohort, or case-control designs, and a follow-up period of at least one year were included. Studies lacking a clear case definition or information on peri-implantitis and those that did not investigate keratinized mucosa as a risk indicator were excluded. DATA EXTRACTION AND SYNTHESIS: Two reviewers independently utilized a systematic review screening website (Rayyan, Qatar Computing Research Institute, Qatar Foundation) to select potential articles, and conflicts were resolved through discussion or consultation with a third reviewer. The data extraction process involved recording information from the included articles, such as study design, patient and implant numbers, prosthesis type (fixed or removable), follow-up duration, peri-implantitis case definition, prevalence at patient and implant levels, keratinized mucosa cutoff value, odds ratio (OR) of peri-implantitis considering keratinized mucosa, and conclusions on the potential effect of keratinized mucosa from each study. The Newcastle Ottawa scale (NOS) and a modified version of NOS were used, respectively, to assess the quality of cohort and cross-sectional studies. Studies scoring below 6 out of 9 points were classified as low quality. For the meta-analysis, the relationship between peri-implantitis and keratinized mucosa was evaluated using the odds ratio (OR) and standard error (SE). Heterogeneity was assessed through the Chi2 test and I2 index, determining whether a random-effects or fixed-effects model should be applied. Subgroup and cluster analyses were conducted based on specific criteria, and forest plots and funnel plots were generated to visualize results and identify potential study bias. Sensitivity analysis was performed to verify the robustness of the meta-analysis, with statistical significance set at p < 0.05. The Review Manager (RevMan) software facilitated data analysis. The GRADE rating system was used to determine the level of evidence, considering factors such as bias risk, imprecision, inconsistency, indirectness, and publication bias. The certainty of the evidence was evaluated based on the overall outcomes of analyzed subgroups. RESULTS: Twenty-two primary studies were identified, and a meta-analysis was conducted on 16 cross-sectional studies. The prevalence of peri-implantitis ranged from 6.68% to 62.3% at the patient level and from 4.5% to 58.1% at the implant level. The overall analysis revealed a significant association between the lack of keratinized mucosa and a higher prevalence of peri-implantitis (OR = 2.78, 95% CI 2.07-3.74, p < 0.00001). Subgroup analyses with a consistent case definition of peri-implantitis (MBL ≥ 2 mm) showed similar results (OR = 1.96, 95% CI 1.41-2.73, p < 0.0001). Studies focusing on fixed prostheses only demonstrated that the lack of keratinized mucosa was associated with an increased prevalence of peri-implantitis (OR = 2.82, 95% CI 1.85-4.28, p < 0.00001). Among patients under regular implant maintenance, the absence of keratinized mucosa significantly raised the occurrence of peri-implantitis (OR = 2.08, 95% CI 1.41-3.08, p = 0.0002). Studies adjusting for other variables also confirmed a higher risk of peri-implantitis with inadequate keratinized mucosa (OR = 3.68, 95% CI 2.32-5.82, p = 0.007). Although some publication bias was observed, the certainty of evidence based on the GRADE system was judged to be "moderate." CONCLUSIONS: The lack of keratinized mucosa increased the risk of peri-implantitis, emphasizing the need to consider it during dental implant placement. Inadequate data on patient-specific factors and the predominance of cross-sectional studies influenced the evidence quality (i.e., moderate). Future studies with consistent methodologies shall confirm these findings and identify additional risk indicators to improve implant dentistry practices.

Three-Dimensional Peri-Implant Tissue Changes in Immediately vs. Early Placed Tapered Implants Restored with Two Different Ceramic Materials-1 Year Results.

BACKGROUND: A prospective multi-center randomized controlled clinical trial was performed to digitally analyze tissue volume changes in immediately and early placed implants with simultaneous bone augmentation restored with two different all-ceramic materials. METHODS: A total of 60 patients received 60 bone-level tapered implants (BLT, Straumann AG) immediately (n = 30) or early placed, 8-10 weeks after tooth extraction, (n = 30). Implants were restored with all-ceramic single crowns fabricated out of zirconia (Lava Plus, 3M), or lithium disilicate (E.max CAD, Ivoclar Vivadent AG) bonded to titanium base abutments (Variobase for Cerec, Straumann AG). Impressions were taken at baseline (BL), 6 and 12 months, and STL data were used to define an area of interest (AOI) to analyze peri-implant volume changes and midfacial recessions. RESULTS: For immediate placement, a mean volume loss of -5.56 mm3 (±5.83 mm3) was found at 6 months, and of -6.62 mm3 (±6.56 mm3) at 12 months. For early placement, a mean volume loss of -1.99 mm3 (±5.82 mm3) at 6 months, and of -3.7 mm3 (±5.62 mm3) at 12 months was found. The differences in volume loss at 12 months between the two implant placement protocols were significant (p = 0.005). In both groups, mean midfacial recessions of 0.48 mm (±0.52) occurred. CONCLUSIONS: A more pronounced peri-implant volume loss can be expected 12 months after immediate implant placement compared with early placement.

Guided Autotransplantation of Impacted Canines Using a CAD/CAM Surgical Template.

Autotransplantation is a potential treatment alternative when orthodontic traction of an impacted tooth is difficult. In this article, we describe two cases of guided autotransplantation of an impacted canine using a computer-aided designed and manufactured surgical template. The impacted canine was segmented on preoperative cone-beam computed tomography images to ensure a sufficient periodontal ligament space and placement of the donor tooth with the least pressure on it. The canine was virtually transposed using a simulation program considering the adjacent teeth. The surgical template, which was connected to the occlusal stop on adjacent teeth, was designed and 3D-printed with polymer resin. The recipient site was prepared using the surgical template, followed by immediate transplantation of the surgically extracted canine into the socket. The transplanted donor tooth was positioned in planned infra-occlusion to prevent occlusal interference. It was then splinted with the adjacent teeth for initial stabilization. During follow-up, one transplanted tooth showed pulp canal obliteration and the other had suspected pulp necrosis; endodontic treatment was performed. One year after the procedure, the periradicular condition of both teeth was favorable.

A comprehensive study on the mechanical effects of implant-supported prostheses under multi-directional loading and different occlusal contact points.

AIMS: To evaluate screw loosening and fracture load and angular deviation of a single implant-supported prosthesis under multi-directional loading condition at three different occlusal contact points. METHODS: A total of 40 metal crowns were cemented to external connection implants and were embedded vertically and obliquely. The occlusal surface of the crown was designed with three flat surfaces, contact a, b, and c, representing outer and inner 20-degree inclination for buccal and lingual cusps. The angular deviations of implant crown under static 50N of loading were measured. And screw removal torque was evaluated before and after 57,600 load cycles. Then, fracture load was measured for each specimen. Data analysis was performed using one-way analysis of variance test of significance followed by Tukey honest significant difference (HSD) test(p < 0.05). RESULTS: Angular deviation results showed statistical significance between all contact points in vertically embedded group compared to obliquely embedded group, which showed similar results between contact A and B compared to C. In the other hand, screw loosening evaluation did not show statistical significance among the tested groups. And for the fracture load evaluation the maximum values reached twice the yield values in all contact areas. CONCLUSIONS: Mechanical effects were different regarding to diverse loading direction and contact points. The results of this study suggest that the stress concentration might increase in unfavorable vector direction.

Bisphenol A release from commercially available 3-dimensionally printed resins and human cell apoptosis to bisphenol A: an in-vitro study.

Bisphenol A (BPA) from dental materials may be linked to children's health issues. This study aimed to assess the release of BPA from commercially available 3-dimensional (3D)-printed resin materials and evaluate BPA-related apoptotic effects on human periodontal ligament cells and gingival fibroblasts. Commercially available 3D-printed resin materials for prosthodontic use were selected as follows: NextDent C&B MFH (3D Systems, Rock Hill, SC, USA), DIOnavi-P. MAX (Dio Co., Busan, Korea), and DIOnavi-Denture02 (Dio Co., Busan, Korea). Identical cuboidal samples (1 cm × 1 cm × 0.5 cm) were printed from the materials and cured. BPA release was assessed using liquid chromatography/mass spectrometry (LC/MS). In addition, human gingival fibroblasts and periodontal ligament cells were exposed to various BPA solutions based on the LC/MS results. Cell Counting kit-8 (CCK-8) and real-time polymerase chain reaction analyses were performed to evaluate BPA-related apoptotic effects. The LC/MS analysis confirmed that none of the 3D-printed resin materials released BPA after curing. Both human gingival fibroblasts and periodontal ligament cells showed lower viability after BPA exposure. Regarding apoptosis-related gene expression, Caspase10 (CASP10) expression in periodontal ligament cells was significantly different in the BPA solutions (p < 0.05). The expression of BAX and Capspase8 (CASP8) in gingival fibroblasts was significantly increased by BPA in a dose-dependent manner (p < 0.05). Within the limitations of this study, the 3D-printed resin materials were not found to release BPA. This finding implies that 3D-printed resin materials are not associated with potential BPA-related risks in children.

3D analysis of occlusal registration through geometry embedded library matching between quadrant and full-arch digital impression.

OBJECTIVE: This study aimed to compare the accuracy of occlusal registration for single-unit restorations in the posterior area of the jaw using the complete-arch or quadrant scan techniques. MATERIALS AND METHODS: A master cast was prepared and articulated on a nonadjustable articulator, and the maxillary left first molar was prepared for a full-coverage crown. The master cast was digitized as the reference data using a laboratory scanner (E3 scanner, 3Shape, Copenhagen, Denmark). It was scanned 10 times in the complete arch and 10 times in the quadrant, with an occlusal registration in each, using four intraoral scanners (i500, Primescan, TRIOS 3, and TRIOS 4). The scanned data were aligned to the reference data using GOM Inspect software. A three-dimensional analysis of the surface-based occlusal clearance and angular deviation, focusing on the prepared tooth, was performed. RESULTS: The mean surface-based occlusal clearance in the quadrant and complete-arch scans was 1.622 ± 0.032 mm and 1.642 ± 0.043 mm, respectively. Angular deviations compared to the reference cast showed a difference of 0.10° distally and 0.09° buccally for the quadrant scan and 0.12° distally and buccally for the complete-arch scan. Statistical analysis was performed using one-way analysis of variance and post hoc Scheffe's test. No significant differences were observed between the test groups. CONCLUSIONS: No significant differences were found between occlusal registrations of the complete-arch and quadrant scans. Therefore, a quadrant scan can achieve the same outcome as a complete-arch scan for single-unit restoration in the posterior area of the jaw. CLINICAL RELEVANCE: Quadrant scanning for single-unit restoration showed similar outcomes as complete-arch scans.

Evaluation of the intaglio surface trueness and fit of zirconia crowns fabricated using different machining strategies with a chairside CAD/CAM system.

AIM: This study aimed to evaluate the intaglio surface trueness and fit of zirconia crowns depending on the different machining strategies used with the CEREC system. MATERIALS AND METHODS: Thirty duplicate tooth models for a single zirconia crown were randomly assigned to the three groups (n = 10) according to the machining mode used for fabrication: grinding, wet milling, and dry milling. The scan data of the final crowns were compared to their design data to evaluate the intaglio surface trueness. The marginal and internal fits were evaluated using the cross-sectional method. The time required for the machining and sintering processes was measured for each group. RESULT: The wet milling group showed better trueness (RMS, 13.8 ± 1.0 µm) than the grinding and dry milling groups (p < 0.001). The marginal gap was greater in the grinding group (58.6 ± 28.9 µm) than that in the wet milling and dry milling groups (p < 0.001). The dry milling group required the shortest time for the manufacturing process. CONCLUSION: All machining modes fabricated crowns with a clinically acceptable trueness and fit. However, the dry milling mode was advantageous for the chairside CAD/CAM system with respect to time efficiency.

Occlusal adjustment of 3-unit tooth-supported fixed dental prostheses fabricated with complete-digital and -analog workflows: A crossover clinical trial.

AIM: This prospective crossover clinical trial aimed to compare the complete-digital and -analog workflows in terms of occlusal adjustment of 3-unit tooth-supported fixed dental prostheses, operator, and patient preferences. MATERIALS AND METHOD: This study included twelve patients receiving fourteen 3-unit posterior FDPs. 2 FDPs were made for each restoration site: one fabricated in complete-digital workflow comprising intraoral scan with static bite registration (Trios 3) and a monolithic zirconia FDP (test); the other fabricated in complete-analog workflow comprising conventional impression/face-bow transfer and a porcelain-fused-to-metal FDP (control). The FDPs (n=28) were intraorally/provisionally fixed, and quadrant-like intraoral scans were taken for every FDP before & after their occlusal adjustments. Pre- and post-adjustment scans of each FDP were then superimposed using best-fit alignment (GOM Inspect) to measure the volumetric occlusal adjustment amount (mm3) (3Matic) (Mann Whitney U, α=0.05). The patient and operator experience for digital and analog workflows were evaluated using visual analog scales (Wilcoxon test, α=0.05). RESULTS: Mean occlusal adjustments were 7.63 mm3 [±7.02] and 25.95 mm3 [±39.61] for test and control groups, respectively. The volumetric adjustment difference was clinically noticeable but not significant (P=0.12). The impression and digital workflow adjustment were perceived more favorably by both operator (P=0.003, P=0.046, respectively) and the patients (P=0.003, P=0.002, respectively). CONCLUSIONS: Within the limitations of this clinical study, the complete digital workflow with digital static bite-registration provided high occlusal accuracy for short-span tooth-supported FDPs. In addition, the patient and operator preferences significantly favored the digital workflow. CLINICAL SIGNIFICANCE: Complete-digital workflow employing intraoral scanning and model-free fabrication of monolithic-Zr short-span tooth-supported FDPs offers an effective treatment modality with sufficient occlusal accuracy. Therefore complete-digital workflow is a valid alternative for complete-analog workflow comprising conventional impression, face-bow transfer, and use of a semi-adjustable articulator.

Automated vector analysis to design implant-supported prostheses: A dental technique.

The prosthesis loading force is an important factor for dental implant survival. Even if adequate osseointegration of the dental implant has been achieved, if the occlusal forces are not correctly distributed, lateral torque can be generated causing high stress on surrounding tissues. The stress value of implant prostheses could be different whether the direction of load is vertical or oblique, affected by the shape of the occlusal surface. When an implant-supported prosthesis is designed with a dental computer-aided design software program, the average vectors from each occlusal contact point can be visualized. If the visualized vector generates lateral torque, the occlusal surface design can be modified before finalizing the design. The described technique uses automated vector analysis to enable visualization of the occlusal vector to improve prosthesis design, optimizing occlusal forces.

Mechanical Properties of Additively Manufactured and Milled Interim 3-Unit Fixed Dental Prostheses.

PURPOSE: To investigate the survival and mechanical properties of 3-unit interim fixed dental prostheses (FDPs) made with additive manufacturing (AM) technology compared to milled and conventional manual fabrication. MATERIALS AND METHODS: Sixty 3-unit interim FDPs replacing the first left mandibular molar were divided in 6 groups (n = 10): manual (Man) (Protemp 4), milled (Mil) (Telio-CAD Multi), and 4 additive manufacturing (AM) groups were subdivided into 4 AM technology subgroups: direct light positioning (DLP) (Rapidshape P30 [RS]), and stereolitography (SLA) (Formlabs 2 [FL]) and the type of printed interim polymer (P Pro C&B [St] and SHERAprint-cb [Sh]) (RS-St, RS-Sh, FL-St, and FL-Sh). Survival and complications were assessed after thermomechanical aging. The surviving samples were tested for fracture resistance. Kaplan-Meier test followed by log-rank test to show differences between groups was used to calculate the survival and complication rates. For fracture strength, one-way ANOVA and Tukey-b post hoc test were used to compare groups. Descriptive statistics was used for failure modes and Pearson chi-square to compare groups (α = 0.05). RESULTS: Survival rates among groups varied from 100% (Man, Mil and FL-Sh), 70% (FL-St), 50% (RS-Sh), and 20% (RS-Sh) (p < 0.001), respectively. Additional events were observed in 50% to 80% in FL-St, RS-St, and RS-Sh groups (p < 0.001). Man, FL-St, and RS-S showed lower mean static load resistance (p < 0.001). Fracture through the connector between tooth 35 and the pontic was the most prevalent type of failure. CONCLUSION: The manufacturing method, type of resin, and the printing mode had a significant influence on the mechanical properties of AM interim 3-unit FDPs.

Comparison of digital and conventional assessment methods for a single tooth preparation and educational satisfaction.

INTRODUCTION: Digital feedback for tooth preparation can provide dental practitioners with more objective and accurate evaluations compared to conventional methods. This study aimed to evaluate the educational effect and satisfaction of digital feedback compared with those of the conventional putty index method for tooth preparation. MATERIAL AND METHODS: Forty-eight third-grade dental students were selected. All students performed a full-coverage preparation on a right mandibular first molar resin tooth. They were randomly divided into four groups (n = 12)-no guide (control), putty index, digital feedback, and digital and putty index assessment. Three-dimensional analysis was performed using an analysis software (GomInspect 2018, Gom) to evaluate the amount of tooth structure removed. At the end of the practice, the students completed a questionnaire to evaluate the educational satisfaction of the respective methods. RESULTS: There was no statistical significance of the amount of preparation amongst groups in most of the measured areas only except for several specific points. Overall occlusal surface showed 0.99 ± 0.27 mm in the N group (no guide) and 1.15 ± 0.31 mm in the D group (digital feedback), and overall axial surface showed no statistical differences (p > .05). The groups that used digital assessment showed a high level of satisfaction compared with conventional assessment. CONCLUSIONS: It was difficult to confirm that the digital-based feedback promotes accurate tooth preparation compared to conventional feedback within the limitation of this study. However, it improved educational satisfaction and permitted objective evaluation.

Stress distribution in pediatric zirconia crowns depending on different tooth preparation and cement type: a finite element analysis.

BACKGROUND: In clinical settings, tooth preparation for prefabricated zirconia crowns (PZCs) in the primary dentition varies widely. However, knowledge about the biomechanical behavior of PZCs in various clinical settings is limited. This study was conducted to evaluate the biomechanical behavior of PZCs in different clinical settings using 3-dimensional finite element analysis. METHODS: 3-dimensional models of the PZC, cement, and tooth with six different conditions were simulated in primary molar teeth, incorporating cement thickness (100, 500, and 1000 µm) and cement type (resin-modified glass ionomer cement and resin cement). A total of 200 N of occlusal force was applied to the models, both vertically and obliquely as representative cases. A general linear model univariate analysis with partial eta-squared (ηp2) was performed to evaluate the relative effects of the variables. RESULTS: The overall stress of tooth was increased as the cement space increases under oblique loading. The von Mises stress values of the resin cements were significantly higher than those of the resin-modified glass ionomer cements for all cement thicknesses (p < .05). The effect size of the cement type (ηp2 = .519) was more dominant than the cement thickness (ηp2 = .132) in the cement layer. CONCLUSIONS: Within the limits of this study, cement type has a greater influence on the biomechanical behavior of PZCs than cement thickness.