Lasing Emission from Soft Photonic Crystals for Pressure and Position Sensing.

In this report, we introduce a 1D photonic crystal (PhC) nanocavity with waveguide-like strain amplifiers within a soft polydimethylsiloxane substrate, presenting it as a potential candidate for highly sensitive pressure and position optical sensors. Due to its substantial optical wavelength response to uniform pressure, laser emission from this nanocavity enables the detection of a minimum applied uniform pressure of 1.6‱ in experiments. Based on this feature, we further studied and elucidated the distinct behaviors in wavelength shifts when applying localized pressure at various positions relative to the PhC nanocavity. In experiments, by mapping wavelength shifts of the PhC nanolaser under localized pressure applied using a micro-tip at different positions, we demonstrate the nanocavity's capability to detect minute position differences, with position-dependent minimum resolutions ranging from tens to hundreds of micrometers. Furthermore, we also propose and validate the feasibility of employing the strain amplifier as an effective waveguide for extracting the sensing signal from the nanocavity. This approach achieves a 64% unidirectional coupling efficiency for leading out the sensing signal to a specific strain amplifier. We believe these findings pave the way for creating a highly sensitive position-sensing module that can accurately identify localized pressure in a planar space.

Enhancing on/off ratio of a dielectric-loaded plasmonic logic gate with an amplitude modulator.

Plasmonic waveguides allow focusing, guiding, and manipulating light at the nanoscale and promise the miniaturization of functional optical nanocircuits. Dielectric-loaded plasmonic (DLP) waveguides and logic gates have drawn attention because of their relatively low loss, easy fabrication, and good compatibility with gain and active tunable materials. However, the rather low on/off ratio of DLP logic gates remains the main challenge. Here, we introduce an amplitude modulator and theoretically demonstrate an enhanced on/off ratio of a DLP logic gate for XNOR operation. Multimode interference (MMI) in DLP waveguide is precisely calculated for the design of the logic gate. Multiplexing and power splitting at arbitrary multimode numbers have been theoretically analyzed with respect to the size of the amplitude modulator. An enhanced on/off ratio of 11.26 dB has been achieved. The proposed amplitude modulator can also be used to optimize the performance of other logic gates or MMI-based plasmonic functional devices.

Dynamic single microparticle manipulation in the far-field region using plasmonic vortex lens multiple arms with a circular groove.

Recent development of particle manipulation has led to high demand for dynamic optical tweezer structures. However, confining and rotating a single microparticle in the far-field region with a uniform potential distribution remains a complicated task. A plasmonic vortex lens (PVL) has been proven to easily rotate the dielectric particle owing to its effect on orbital angular momentum (OAM). Here we propose and demonstrate PVL multiple arms with a circular groove (CG). The device consists of a multiple arm spiral slit that generates a plasmonic vortex (PV) and a circular groove to bring the PV from the surface to the far-field region. Numerical simulations are performed to calculate the intensity distribution of the primary ring, the optical force and potential. The primary ring size can be adjusted using different polarization directions. PVL 2-arms with a CG has primary ring sizes of 1082 nm under right-handed circular polarization (RCP) and 517 nm under left-handed circular polarization (LCP). Based on these primary ring sizes, a 1 µm polystyrene (PS) bead can be rotated under RCP with a minimum required power of 7.45 mW and trapped under LCP with a minimum required power of 11.84 mW. For PVL 4-arms with a CG under RCP illumination, we optimize the uniform potential distribution by carefully selecting the radius of the groove. Using a groove radius of 1050 nm, we obtain the potential difference between the smallest and largest depth along the x- and y-directions of only 70 k B T/W with a minimum required power of 14.86 mW. The method and design discussed here offer an efficient way to manipulate microparticles for micro-rotors, cell dynamic analysis, etc.

Ultra-compact Archimedes spiral plasmonic lens with a circular groove for low power optical trapping in the far-field region.

Particle levitation is crucial in optical trapping considering contamination and alteration of the character of the particle due to physical contact with the structure. A strong field gradient along the optical axis is required in this case. To manipulate the particle at a distance from the surface, we propose an Archimedes spiral plasmonic lens with a circular groove (CG-ASPL). The optical properties and parameters influencing the trapping performance of CG-ASPL are fully analyzed and discussed. By illuminating the structure with circular polarization and structure optimization, we can reduce the required optical power down to 2.4 mW for trapping particle of 1 µm in diameter with groove width and height of 100 and 125 nm, respectively. The particle can be stably trapped with trapping potential of 4138 kBT/W in the far-field region (1.1λ) owing to constructive interference of the scattered SPP waves. Furthermore, this structure is ultra-compact with a size of about 6.7 µm in diameter. We believe the results demonstrated in this work would be very useful for lab-on-a-chip applications and many others.

Layered Graphene Growth Directly on Sapphire Substrates for Applications.

Layer-by-layer graphene growth is demonstrated by repeating CVD growth cycles directly on sapphire substrates. Improved field-effect mobility values are observed for the bottom-gate transistors fabricated by using the bilayer graphene channel, which indicates an improved crystallinity is obtained after the second CVD growth cycle. Despite the poor wettability of copper on graphene surfaces, graphene may act as a thin and effective diffusion barrier for copper atoms. The low resistivity values of thin copper films deposited on thin monolayer MoS2/monolayer graphene heterostructures have demonstrated its potential to replace current thick liner/barrier stacks in back-end interconnects. The unique van der Waals epitaxy growth mode will be helpful for both homo- and heteroepitaxy on 2D material surfaces.

Advanced Atomic Layer Deposition Technologies for Micro-LEDs and VCSELs.

In recent years, the process requirements of nano-devices have led to the gradual reduction in the scale of semiconductor devices, and the consequent non-negligible sidewall defects caused by etching. Since plasma-enhanced chemical vapor deposition can no longer provide sufficient step coverage, the characteristics of atomic layer deposition ALD technology are used to solve this problem. ALD utilizes self-limiting interactions between the precursor gas and the substrate surface. When the reactive gas forms a single layer of chemical adsorbed on the substrate surface, no reaction occurs between them and the growth thickness can be controlled. At the Å level, it can provide good step coverage. In this study, recent research on the ALD passivation on micro-light-emitting diodes and vertical cavity surface emitting lasers was reviewed and compared. Several passivation methods were demonstrated to lead to enhanced light efficiency, reduced leakage, and improved reliability.

Photonic Crystal Polymeric Thin-Film Dye-Lasers for Attachable Strain Sensors.

In this report, using two-dimensional photonic crystals (PhC) and a one-dimensional PhC nano-beam cavity, we realized the development of all-polymeric dye-lasers on a dye-doped, suspended poly-methylmethacrylate film with a wavelength-scale thickness. In addition to the characterization of basic lasing properties, we also evaluated its capacity to serve as an attachable strain sensor. Through experimentation, we confirmed the stable lasing performances of the dye-laser attaching on a rough surface. Moreover, we also theoretically studied the wavelength responses of the utilized PhC resonators to stretching strain and further improved them via the concept of strain shaping. The attachability and high strain sensing response of the presented thin film PhC dye-lasers demonstrate their potential as attachable strain sensors.

MoS2 with Stable Photoluminescence Enhancement under Stretching via Plasmonic Surface Lattice Resonance.

In this study, by combining a large-area MoS2 monolayer with silver plasmonic nanostructures in a deformable polydimethylsiloxane substrate, we theoretically and experimentally studied the photoluminescence (PL) enhancement of MoS2 by surface lattice resonance (SLR) modes of different silver plasmonic nanostructures. We also observed the stable PL enhancement of MoS2 by silver nanodisc arrays under differently applied stretching strains, caused by the mechanical holding effect of the MoS2 monolayer. We believe the results presented herein can guarantee the possibility of stably enhancing the light emission of transition metal dichalcogenides using SLR modes in a deformable platform.

Highly Efficient and Stable White Light-Emitting Diodes Using Perovskite Quantum Dot Paper.

Perovskite quantum dots (PQDs) are a competitive candidate for next-generation display technologies as a result of their superior photoluminescence, narrow emission, high quantum yield, and color tunability. However, due to poor thermal resistance and instability under high energy radiation, most PQD-based white light-emitting diodes (LEDs) show only modest luminous efficiency of ≈50 lm W-1 and a short lifetime of <100 h. In this study, by incorporating cellulose nanocrystals, a new type of QD film is fabricated: CH3NH3PbBr3 PQD paper that features 91% optical absorption, intense green light emission (518 nm), and excellent stability attributed to the complexation effect between the nanocellulose and PQDs. The PQD paper is combined with red K2SiF6:Mn4+ phosphor and blue GaN LED chips to fabricate a high-performance white LED demonstrating ultrahigh luminous efficiency (124 lm W-1), wide color gamut (123% of National Television System Committee), and long operation lifetime (240 h), which paves the way for advanced lighting technology.

Design, Modeling, and Fabrication of High-Speed VCSEL with Data Rate up to 50 Gb/s.

We have studied the characteristics of frequency response at 850-nm GaAs high-speed vertical-cavity surface-emitting lasers (VCSELs) with different kinds of oxide aperture sizes and cavity length using the PICS3D simulation program. Using 5-µm oxide aperture sizes, the frequency response behavior can be improved from 18.4 GHz and 15.5 GHz to 21.2 GHz and 19 GHz in a maximum of 3 dB at 25 °C and 85 °C, respectively. Numerical simulation results also suggest that the frequency response performances improved from 21.2 GHz and 19 GHz to 30.5 GHz and 24.5 GHz in a maximum of 3 dB at 25 °C and 85 °C due to the reduction of cavity length from 3λ/2 to λ/2. Consequently, the high-speed VCSEL devices were fabricated on a modified structure and exhibited 50-Gb/s data rate at 85 °C.

Liquid Type Nontoxic Photoluminescent Nanomaterials for High Color Quality White-Light-Emitting Diode.

High-brightness white-light-emitting diodes (w-LEDs) with excellent color quality is demonstrated by using nontoxic nanomaterials. Previously, we have reported the high color quality w-LEDs with heavy-metal phosphor and quantum dots (QDs), which may cause environmental hazards. In the present work, liquid-type white LEDs composed of nontoxic materials, named as graphene and porous silicon quantum dots are fabricated with a high color rendering index (CRI) value gain up to 95. The liquid-typed device structure possesses minimized surface temperature and 25% higher value of luminous efficiency as compare to dispensing-typed structure. Further, the as-prepared device is environment friendly and attributed to low toxicity. The low toxicity and high R9 (87) component values were conjectured to produce new or improve current methods toward bioimaging application.

Efficient modulation of subwavelength focusing via meta-aperture-based plasmonic lens for multifunction applications.

Subwavelength focusing is crucial for many applications in photonics including super-resolution micro/nanoscopy, nanolithography, and optical trapping. However, most nanostructures exhibit poor ability to modulate focusing spot, which makes them hard to achieve ultra-small resolution. Here, we propose three kinds of plasmonic lens (PL) by utilizing different meta-aperture designs for efficient subwavelength focusing modulation. The shape of nanoaperture strongly influences the diffraction properties. Spatial modulation of focusing spot by employing a circular array of proposed nanoapertures is explored. The best focusing performance among these PLs is the design of T-shape nanoaperture, which has great resolution achieving ultra-small focusing spot of 0.14 λ2 and 0.20 λ2 (λ = 633 nm) for simulation and experiment respectively, better than lots of focusing devices especially by using linear polarization. Multiple-object trapping can be realized by using T-shape nanoaperture-based PL. Our designed PLs with different nanoapertures demonstrate the capability to broaden and integrate different functionalities for on-chip nanotechnologies development.

Engineering surface lattice resonance of elliptical gold nanodisk array for enhanced strain sensing.

We demonstrate an elliptical gold nanodisk array (GNA) for engineering the spectral profile of surface lattice resonance (SLR). The nanodisk's shape has a great impact on SLR. Small linewidth of 20 nm at an aspect ratio of 1.17, as well as large wavelength tuning of 64 nm within 4% strain via different orientations and polarizations, are achieved experimentally. The enhanced wavelength response of 6.93 nm per 1% strain variation for elliptical GNA is 2.4 times better than that for general circular GNA. Furthermore, the strain sensing for elliptical GNA approaches is 5.7 times greater than that for circular GNA.

Thermally Strained Band Gap Engineering of Transition-Metal Dichalcogenide Bilayers with Enhanced Light-Matter Interaction toward Excellent Photodetectors.

Integration of strain engineering of two-dimensional (2D) materials in order to enhance device performance is still a challenge. Here, we successfully demonstrated the thermally strained band gap engineering of transition-metal dichalcogenide bilayers by different thermal expansion coefficients between 2D materials and patterned sapphire structures, where MoS2 bilayers were chosen as the demonstrated materials. In particular, a blue shift in the band gap of the MoS2 bilayers can be tunable, displaying an extraordinary capability to drive electrons toward the electrode under the smaller driven bias, and the results were confirmed by simulation. A model to explain the thermal strain in the MoS2 bilayers during the synthesis was proposed, which enables us to precisely predict the band gap-shifted behaviors on patterned sapphire structures with different angles. Furthermore, photodetectors with enhancement of 286% and 897% based on the strained MoS2 on cone- and pyramid-patterned sapphire substrates were demonstrated, respectively.

Compressible 1D photonic crystal nanolasers with wide wavelength tuning.

We propose and demonstrate a tunable photonic crystal nanolaser consisting of 1D periodic nanorods wrapped in deformable polydimethylsiloxane. In addition to low-threshold and long-term lasing stability, the nanolaser also displays reproducible and reliable wavelength tuning with a large tunability of 7.7 nm under 1% compression. By further associating with stretching, a very wide wavelength-tunable range of 155 nm that almost spans the entire S+C+L telecommunication bands is successfully demonstrated with a single nanolaser device.

Wavelength tunable InGaN/GaN nano-ring LEDs via nano-sphere lithography.

In this research, nano-ring light-emitting diodes (NRLEDs) with different wall width (120 nm, 80 nm and 40 nm) were fabricated by specialized nano-sphere lithography technology. Through the thinned wall, the effective bandgaps of nano-ring LEDs can be precisely tuned by reducing the strain inside the active region. Photoluminescence (PL) and time-resolved PL measurements indicated the lattice-mismatch induced strain inside the active region was relaxed when the wall width is reduced. Through the simulation, we can understand the strain distribution of active region inside NRLEDs. The simulation results not only revealed the exact distribution of strain but also predicted the trend of wavelength-shifted behavior of NRLEDs. Finally, the NRLEDs devices with four-color emission on the same wafer were demonstrated.

A Comprehensive Study of One-Step Selenization Process for Cu(In1-x Ga x )Se2 Thin Film Solar Cells.

In this work, aiming at developing a rapid and environmental-friendly process for fabricating CuIn1-x Ga x Se2 (CIGS) solar cells, we demonstrated the one-step selenization process by using selenium vapor as the atmospheric gas instead of the commonly used H2Se gas. The photoluminescence (PL) characteristics indicate that there exists an optimal location with superior crystalline quality in the CIGS thin films obtained by one-step selenization. The energy dispersive spectroscopy (EDS) reveals that the Ga lateral distribution in the one-step selenized CIGS thin film is intimately correlated to the blue-shifted PL spectra. The surface morphologies examined by scanning electron microscope (SEM) further suggested that voids and binary phase commonly existing in CIGS films could be successfully eliminated by the present one-step selenization process. The agglomeration phenomenon attributable to the formation of MoSe2 layer was also observed. Due to the significant microstructural improvement, the current-voltage (J-V) characteristics and external quantum efficiency (EQE) of the devices made of the present CIGS films have exhibited the remarkable carrier transportation characteristics and photon utilization at the optimal location, resulting in a high conversion efficiency of 11.28%. Correlations between the defect states and device performance of the one-step selenized CIGS thin film were convincingly delineated by femtosecond pump-probe spectroscopy.

Effective optimization and analysis of white LED properties by using nano-honeycomb patterned phosphor film.

This study presents an approach for patterning a polydimethylsiloxane (PDMS) phosphor film with a photonic crystal nano-honeycomb structure on a blue chip package. A phosphor film with a nano-honeycomb structure was patterned and transferred using a nanosphere and used for fabricating remote white light-emitting diodes (w-LEDs). The angular correlated color temperature deviation of the remote phosphor LED could be improved by varying nano-honeycomb structure pitches (450, 750, and 1150 nm). In particular, w-LED samples with excellent color uniformity (ΔCCT ranging from 940 to 440 K) were fabricated from 750-nm w-LED samples with nano-honeycomb-patterned tops.

Optical Properties of Plasmonic Mirror-Image Nanoepsilon.

We propose a novel mirror-image nanoepsilon (MINE) structure to achieve highly localized and enhanced near field at its gap and systematically investigate its plasmonic behaviors. The MINE can be regarded as a combination of two fundamental plasmonic nanostructures: a nanorod dimer and nanoring. By adapting a nanoring surrounding a nanorod dimer structure, the nanorod is regarded as a bridge pulling the charges from the nanoring to the nanorod, which induces stronger plasmon coupling in the gap to boost local near-field enhancement. Two resonance peaks are identified as the symmetric and anti-symmetric modes according to the symmetries of the charge distributions on the ring and rod dimer in the MINE. The symmetric mode in the MINE structure is preferred because its charge distribution leads to stronger near-field enhancement with a concentrated distribution around the gap. In addition, we investigate the influence of geometry on the optical properties of MINE structures by performing experiments and simulations. These results indicate that the MINE possesses highly tunable optical properties and that significant near-field enhancement at the gap region and rod tips can be realized by the gap and lightning-rod effects. The results improve understanding of such complex systems, and it is expected to guide and facilitate the design of optimum MINE structures for various plasmonic applications.