Beyond dispersive liquid-liquid microextraction.

Dispersive liquid-liquid microextraction (DLLME) and other dispersion liquid-phase microextraction (LPME) methods have been developed since the first DLLME method was reported in 2006. DLLME is simple, rapid, and affords high enrichment factor, this is due to the large contact surface area of the extraction solvent. DLLME is a method suitable for the extraction in many different water samples, but it requires using chlorinated solvents. In recent years, interest in DLLME or dispersion LPME has been focused on the use of low-toxicity solvents and more conveniently practical procedures. This review examines some of the most interesting developments in the past few years. In the first section, DLLME methods are separated in two categories: DLLME with low-density extraction solvent and DLLME with high-density extraction solvent. Besides these methods, many novel special devices for collecting low-density extraction solvent are also mentioned. In addition, various dispersion techniques with LPME, including manual shaking, air-assisted LPME (aspirating and injecting the extraction mixture by syringe), ultrasound-assisted emulsification, vortex-assisted emulsification, surfactant-assisted emulsification, and microwave-assisted emulsification are described. Besides the above methods, combinations of DLLME with other extraction techniques (solid-phase extraction, stir bar sorptive extraction, molecularly imprinted matrix solid-phase dispersion and supercritical fluid extraction) are introduced. The combination of nanotechnique with DLLME is also introduced. Furthermore, this review illustrates the application of DLLME or dispersion LPME methods to separate and preconcentrate various organic analytes, inorganic analytes, and samples.

Up-and-down shaker-assisted ionic liquid-based dispersive liquid-liquid microextraction of benzophenone-type ultraviolet filters.

Sun protection is an important part of our lives. UV filters are widely used to absorb solar radiation in sunscreens. However, excess UV filters constitute persistent groups of organic micropollutants present in the environment. An environmentally friendly ionic-liquid-based up-and-down shaker-assisted dispersive liquid-liquid microextraction device combined with ultra-performance liquid chromatography coupled with photodiode-array detection has been developed to preconcentrate three UV filters (benzophenone, 2-hydroxy-4-methoxybenzophenone, 2,2'-dihydroxy-4-methoxybenzophenone) from field water samples. In this method, the optimal conditions for the proposed extraction method were: 40 µL [C8MIM][PF6 ] as extraction solvent and 200 µL methanol as disperser solvent were used to extract the UV filters. After up-and-down shaking for 3 min, the aqueous solution was centrifuged at 5000 rpm speed, then using microtube to collect the settled extraction solvent and using ultra-performance liquid chromatography for further analysis. Quantification results indicated that the linear range was 2-1000 ng/mL. The LOD of this method was in the range 0.2-1.3 ng/mL with r(2) ≥ 0.9993. The relative recovery in studies of different types of field water samples was in the range 92-120%, and the RSD was 2.3-7.1%. The proposed method was also applied to the analysis of field samples.

Determination of nitrophenols using ultrahigh pressure liquid chromatography and a new manual shaking-enhanced, ultrasound-assisted emulsification microextraction method based on solidification of a floating organic droplet.

Nitrophenols are toxic compounds in the wastewater. In the proposed method, a new technique using a manual shaking-enhanced, ultrasound-assisted emulsification microextraction (MS-USAEME) method based on solidification of a floating organic droplet combined with ultrahigh pressure liquid chromatography (UHPLC) has been developed for the extraction and determination of nitrophenols in aqueous samples. In this method, the low toxicity extraction solvent 1-undecanol was used to extract the nitrophenols. After centrifugation, ice bath was used to solidify the floating extraction solvent, using microtubes to collect the floated extraction solvent and diluting with 30 µL of dimethyl sulfoxide, then injecting into the UHPLC for further analysis. The relative standard deviations (RSD) were 6-12%, enrichment factors (EFs) were 62-500, the relative recoveries (RR) of this method were 80-110% for spiked lake water samples. The detection limits of this method were 0.5-3.0 µg L⁻¹ for spiked lake water and 0.6-3.2 µg L⁻¹ for spiked agriculture water. The further performance of the proposed method was gauged by analyzing field samples.

Determination of endocrine-disrupting phenols in water samples by a new manual shaking-enhanced, ultrasound-assisted emulsification microextraction method.

Manual shaking-enhanced, ultrasound-assisted emulsification microextraction (MS-USAEME) combined with ultraperformance liquid chromatography (UPLC) with UV detection has been developed for the determination of five endocrine-disrupting phenols (EDPs) in seawater samples and detergent samples: 4-tert-butylphenol (4-t-BP), 4-cumylphenol (4-CP), 4-tert-octylphenol (4-t-OP), 2,4-di-tert-butylphenol (2,4-di-t-BP) and 4-nonylphenol (4-NP). Optimum conditions were found to be: 25 µL 1-bromohexadecane as extraction solvent, 5 mL of aqueous sample and 1 g of NaCl to control the ionic strength; manual shaking for 10 s; ultrasonication for 1 min; centrifugation for 3 min at 5000 rpm (speed). For MS-USAEME, manual shaking for 10 s is essential for effective extraction when the ultrasonic extraction time is as brief as 1 min. The small volume of aqueous sample enhances the effect of manual shaking significantly. For seawater samples, the limit of detection (LOD) was 0.5-2.8 ng mL(-1), the limit of quantification (LOQ) was 1.8-9.3 ng mL(-1) with the relative standard deviation (RSD) in the range 4.2-10.3%. For detergent samples, the LOD was 0.4-2.4 ng mL(-1), LOQ was 1.6-8.2 ng mL(-1) and RSD 4.7-10.0%. The relative recovery was 96-109% for seawater samples and 81-106% for the detergent samples.

Determination of volatile organic compounds in water using ultrasound-assisted emulsification microextraction followed by gas chromatography.

Volatile organic compounds (VOCs) are toxic compounds in the air, water and land. In the proposed method, ultrasound-assisted emulsification microextraction (USAEME) combined with gas chromatography-mass spectrometry (GC-MS) has been developed for the extraction and determination of eight VOCs in water samples. The influence of each experimental parameter of this method (the type of extraction solvent, volume of extraction solvent, salt addition, sonication time and extraction temperature) was optimized. The procedure for USAEME was as follows: 15 µL of 1-bromooctane was used as the extraction solvent; 10 mL sample solution in a centrifuge tube with a cover was then placed in an ultrasonic water bath for 3 min. After centrifugation, 2 µL of the settled 1-bromooctane extract was injected into the GC-MS for further analysis. The optimized results indicated that the linear range is 0.1-100.0 µg/L and the limits of detection (LODs) are 0.033-0.092 µg/L for the eight analytes. The relative standard deviations (RSD), enrichment factors (EFs) and relative recoveries (RR) of the method when used on lake water samples were 2.8-9.5, 96-284 and 83-110%. The performance of the proposed method was gauged by analyzing samples of tap water, lake water and river water samples.

Development of liquid phase microextraction based on manual shaking and ultrasound-assisted emulsification method for analysis of organochlorine pesticides in aqueous samples.

A novel method using sample preparation method, "ultrasound-assisted emulsification microextraction" (USAEME) with manual shaking, coupled with gas chromatography using and an electron capture detector (GC-ECD) was developed for the analysis of organochlorine pesticides (OCPs) in aqueous samples. The apparatus is simple and easy to operate. After manual shaking for 10s, ultrasound was used to accelerate emulsification of the organic solvent (1-decanol) in aqueous solution. Only 10 µL of the low-toxicity extraction solvent is used in this method; no dispersive solvent is required and the total extraction time is ∼4 min. Manual shaking before ultrasound-assisted emulsification enhances the extraction efficiency by >100%. The effects of horizontal and vertical orientation as well as the location of the sample within the ultrasonic bath were studied. After centrifugation, we used an improved solvent collection system (ISCS) to reduce the amount of extraction solvent required. A 1 µL sample of the extract was injected into the GC column. Under optimum conditions, the linear range of the method is 5-2500 ngL(-1) for most of the OCPs, and the limit of detection of the method ranged from 0.6 to 2.9 ngL(-1).The relative recoveries ranged from 75 to 107% for sea water and from 70 to 99% for field fresh water. The method, which provides good enrichment factors, low LODs and minimization of the consumption of organic solvent, provides a rapid, simple and environment-friendly procedure for determining OCPs in aqueous samples.

Determination of phenoxyacetic acids and chlorophenols in aqueous samples by dynamic liquid-liquid-liquid microextraction with ion-pair liquid chromatography.

Dynamic liquid-liquid-liquid microextraction coupled with ion-pair liquid chromatography (IP-LC) and photodiode array detection was developed and used for the extraction and analysis of chlorinated phenoxyacetic acids (CPAs) and chlorophenols (CPs) from water samples. An organic extraction solvent mixture was chosen to simultaneously and effectively extract both CPAs and CPs from aqueous samples. The method detection limit (MDL) ranged from 0.06 to 0.45 µg L(-1) with good reproducibility. The relative standard deviations were in the range of 2.6-6.5% at lower spiked concentrations and 3.0-4.6% at higher concentrations. Good linearity of analytes was achieved in the range of 0.5-500 µg L(-1). The acceptable relative recoveries (82.9-112.4%) for environmental waters revealed the presence of negligible matrix effects in the case of real samples. The applicability of this newly developed method was illustrated by determinations of CPAs and CPs in environmental water samples.

Low toxic dispersive liquid-liquid microextraction using halosolvents for extraction of polycyclic aromatic hydrocarbons in water samples.

A low toxic dispersive liquid-liquid microextraction (LT-DLLME) combined with gas chromatography-mass spectrometry (GC-MS) had been developed for the extraction and determination of 16 polycyclic aromatic hydrocarbons (PAHs) in water samples. In normal DLLME assay, chlorosolvent had been widely used as extraction solvents; however, these solvents are environmental-unfriendly. In order to solve this problem, we proposed to use low toxic bromosolvent (1-bromo-3-methylbutane, LD(50) 6150mg/kg) as the extraction solvent. In this study we compared the extraction efficiency of five chlorosolvents and thirteen bromo/iodo solvents. The results indicated that some of the bromo/iodo solvents showed better extraction and had much lower toxicity than chlorosolvents. We also found that propionic acid is used as the disperser solvent, as little as 50microL is effective. Under optimum conditions, the range of enrichment factors and extraction recoveries of tap water samples are ranging 372-1308 and 87-105%, respectively. The linear range is wide (0.01-10.00microgL(-1)), and the limits of detection are between 0.0003 and 0.0078microgL(-1) for most of the analytes. The relative standard deviations (RSD) for 0.01microgL(-1) of PAHs in tap water were in the range of 5.1-10.0%. The performance of the method was gauged by analyzing samples of tap water, sea water and lake water samples.

Dispersive liquid-liquid microextraction method based on solidification of floating organic drop for extraction of organochlorine pesticides in water samples.

A new simple and rapid dispersive liquid-liquid microextraction method has been developed for the extraction and analysis of organochlorine pesticides (OCPs) in water samples. The method is based on the solidification of a floating organic drop (DLLME-SFO) and is combined with gas chromatography/electron capture detection (GC/ECD). Very little solvent is required in this method. The disperser solvent (200microL acetonitrile) containing 10microL hexadecane (HEX) is rapidly injected by a syringe into the 5.0mL water sample. After centrifugation, the fine HEX droplets (6+/-0.5microL) float at the top of the screw-cap test tube. The test tube is then cooled in an ice bath. After 5min, the HEX solvent solidifies and is then transferred into a conical vial, where it melts quickly at room temperature, and 1microL of it is injected into a gas chromatograph for analysis. Under optimum conditions, the enrichment factors and extraction recoveries are high and range between 37-872 and 82.9-102.5%, respectively. The linear range is wide (0.025-20microgL(-1)), and the limits of detection are between 0.011 and 0.11microgL(-1) for most of the analytes. The relative standard deviation (RSD) for 1microgL(-1) of OCPs in water was in the range of 5.8-8.8%. The performance of the method was gauged by analyzing samples of lake and tap water.

Dispersive liquid-liquid microextraction method based on solidification of floating organic drop combined with gas chromatography with electron-capture or mass spectrometry detection.

A simple dispersive liquid-liquid microextraction (DLLME) method based on solidification of a floating organic drop (DLLME-SFO) technique combined with gas chromatography/electron-capture detection (GC/ECD) or gas chromatography/mass spectrometry (GC/MS) has been developed. The proposed method is simple, low in cost, and of high precision. It overcomes the most important problem in DLLME, the high-toxic solvent used. Halogenated organic compounds (HOCs) in water samples were determined as the model compounds. The parameters optimized for the DLLME-SFO technique were as follows: A mixture of 0.5 mL acetone, containing 10 microL 2-dodecanol (2-DD-OH), was rapidly injected by syringe into the 5 mL water sample. After centrifugation, the fine 2-DD-OH droplets (8+/-0.5 microL) were floated at the top of the screwcap test tube. The test tube was then cooled in an ice bath. After 5 min the 2-DD-OH solvent had solidified and was then transferred into a conical vial; it melted quickly at room temperature and 3 microL (for GC/ECD) or 2 microL (for GC/MS) of it was injected into a gas chromatograph for analysis. The limit of detection (LOD) for this technique was 0.005-0.05microgL(-1) for GC/ECD and was 0.005-0.047 microgL(-1) for GC/MS, respectively. The linear range of the calibration curve of DLLME-SFO was from 0.01 to 500 microgL(-1) with a coefficient of estimation (r2)>0.996 for GC/ECD and was from 0.02 to 500 microgL(-1) with a coefficient of estimation (r2)>0.996 for GC/MS.

H2O2/nitrite-induced post-translational modifications of human hemoglobin determined by mass spectrometry: redox regulation of tyrosine nitration and 3-nitrotyrosine reduction by antioxidants.

Covalent modifications of proteins by endogenous reactive nitrogen oxide species lead to cytotoxic effects that are implicated in diseases associated with chronic infections and inflammation. Tyrosine nitration is a major post-translational modification of proteins by reactive nitrogen oxide species. Recent studies suggest that nitrotyrosine is not a permanent protein modification. We previously demonstrated that lipoyl dehydrogenase is capable of converting 3-nitrotyrosine into 3-aminotyrosine in the presence of certain reducing agents. In this study, we compared the abilities of various hemoproteins, hemin, and the cobalt-containing cofactor cyanocobalamin to mediate H(2)O(2)/nitrite-dependent tyrosine nitration and found that these hemoproteins and metal-containing cofactors also catalyzed the reduction of 3-nitrotyrosine to various extents in the presence of thiol reducing agents or ascorbate. The H(2)O(2)/nitrite-induced post-translational modifications of human hemoglobin identified by nanoLC/nanospray ionization tandem mass spectrometric analysis of the tryptic digest include nitration of tyrosine and tryptophan, as well as oxidation of methionine and cysteine residues. Nitration of human hemoglobin by H(2)O(2)/nitrite was detected on Tyr24 and Tyr42 (alpha-chain) and on Tyr130 and Trp15 (beta-chain) in the alphabeta-dimer. Oxidation of methionine and cysteine residues was also observed. Furthermore, hemoglobin also catalyzed nitro reduction of 3-nitrotyrosine to form 3-aminotyrosine, at Tyr24 in the alpha-chain peptide of human Hb in the presence of ascorbate. The enhanced peroxidase activity of nitrated hemoglobin can be reversed by the antioxidant ascorbate. These results suggest a possible in vivo pathway for hemoglobin contributing to denitration of nitrated proteins through redox regulation.