Towards zero pollution vehicles by advanced fuels and exhaust aftertreatment technologies.

Vehicular emissions deteriorate air quality in urban areas notably. The aim of this study was to conduct an in-depth characterization of gaseous and particle emissions, and their potential to form secondary aerosol emissions, of the cars meeting the most recent emission Euro 6d standards, and to investigate the impact of fuel as well as engine and aftertreatment technologies on pollutants at warm and cold ambient temperatures. Studied vehicles were a diesel car with a diesel particulate filter (DPF), two gasoline cars (with and without a gasoline particulate filter (GPF)), and a car using compressed natural gas (CNG). The impact of fuel aromatic content was examined for the diesel car and the gasoline car without the GPF. The results showed that the utilization of exhaust particulate filter was important both in diesel and gasoline cars. The gasoline car without the GPF emitted relatively high concentrations of particles compared to the other technologies but the implementation of the GPF decreased particle emissions, and the potential to form secondary aerosols in atmospheric processes. The diesel car equipped with the DPF emitted low particle number concentrations except during the DPF regeneration events. Aromatic-free gasoline and diesel fuel efficiently reduced exhaust particles. Since the renewal of vehicle fleet is a relatively slow process, changing the fuel composition can be seen as a faster way to affect traffic emissions.

Particle lung deposited surface area (LDSAal) size distributions in different urban environments and geographical regions: Towards understanding of the PM2.5 dose-response.

Recent studies indicate that monitoring only fine particulate matter (PM2.5) may not be enough to understand and tackle the health risk caused by particulate pollution. Health effects per unit PM2.5 seem to increase in countries with low PM2.5, but also near local pollution sources (e.g., traffic) within cities. The aim of this study is to understand the differences in the characteristics of lung-depositing particles in different geographical regions and urban environments. Particle lung deposited surface area (LDSAal) concentrations and size distributions, along with PM2.5, were compared with ambient measurement data from Finland, Germany, Czechia, Chile, and India, covering traffic sites, residential areas, airports, shipping, and industrial sites. In Finland (low PM2.5), LDSAal size distributions depended significantly on the urban environment and were mainly attributable to ultrafine particles (<100 nm). In Central Europe (moderate PM2.5), LDSAal was also dependent on the urban environment, but furthermore heavily influenced by the regional aerosol. In Chile and India (high PM2.5), LDSAal was mostly contributed by the regional aerosol despite that the measurements were done at busy traffic sites. The results indicate that the characteristics of lung-depositing particles vary significantly both within cities and between geographical regions. In addition, ratio between LDSAal and PM2.5 depended notably on the environment and the country, suggesting that LDSAal exposure per unit PM2.5 may be multiple times higher in areas having low PM2.5 compared to areas with continuously high PM2.5. These findings may partly explain why PM2.5 seems more toxic near local pollution sources and in areas with low PM2.5. Furthermore, performance of a typical sensor based LDSAal measurement is discussed and a new LDSAal2.5 notation indicating deposition region and particle size range is introduced. Overall, the study emphasizes the need for country-specific emission mitigation strategies, and the potential of LDSAal concentration as a health-relevant pollution metric.

Toxicity of exhaust emissions from high aromatic and non-aromatic diesel fuels using in vitro ALI exposure system.

The differences in the traffic fuels have been shown to affect exhaust emissions and their toxicity. Especially, the aromatic content of diesel fuel is an important factor considering the emissions, notably particulate matter (PM) concentrations. The ultra-fine particles (UFP, particles with a diameter of <100 nm) are important components of engine emissions and connected to various health effects, such as pulmonary and systematic inflammation, and cardiovascular disorders. Studying the toxicity of the UFPs and how different fuel options can be used for mitigating the emissions and toxicity is crucial. In the present study, emissions from a heavy-duty diesel engine were used to assess the exhaust emission toxicity with a thermophoresis-based in vitro air-liquid interface (ALI) exposure system. The aim of the study was to evaluate the toxicity of engine exhaust and the potential effect of 20 % aromatic fossil diesel and 0 % aromatic renewable diesel fuel on emission toxicity. The results of the present study show that the aromatic content of the fuel increases emission toxicity, which was seen as an increase in genotoxicity, distinct inflammatory responses, and alterations in the cell cycle. The increase in genotoxicity was most likely due to the PM phase of the exhaust, as the exposures with high-efficiency particulate absorbing (HEPA)-filtered exhaust resulted in a negligible increase in genotoxicity. However, the solely gaseous exposures still elicited immunological responses. Overall, the present study shows that decreasing the aromatic content of the fuels could be a significant measure in mitigating traffic exhaust toxicity.

Snapshots of wintertime urban aerosol characteristics: Local sources emphasized in ultrafine particle number and lung deposited surface area.

Urban air fine particles are a major health-relating problem. However, it is not well understood how the health-relevant features of fine particles should be monitored. Limitations of PM2.5 (mass concentration of sub 2.5 µm particles), which is commonly used in the health effect estimations, have been recognized and, e.g., World Health Organization (WHO) has released good practice statements for particle number (PN) and black carbon (BC) concentrations (2021). In this study, a characterization of urban wintertime aerosol was done in three environments: a detached housing area with residential wood combustion, traffic-influenced streets in a city centre and near an airport. The particle characteristics varied significantly between the locations, resulting different average particle sizes causing lung deposited surface area (LDSA). Near the airport, departing planes had a major contribution on PN, and most particles were smaller than 10 nm, similarly as in the city centre. The high hourly mean PN (>20 000 1/cm3) stated in the WHO's good practices was clearly exceeded near the airport and in the city centre, even though traffic rates were reduced due to a SARS-CoV-2-related partial lockdown. In the residential area, wood combustion increased both BC and PM2.5, but also PN of sub 10 and 23 nm particles. The high concentrations of sub 10 nm particles in all the locations show the importance of the chosen lower size limit of PN measurement, e.g., WHO states that the lower limit should be 10 nm or smaller. Furthermore, due to ultrafine particle emissions, LDSA per unit PM2.5 was 1.4 and 2.4 times higher near the airport than in the city centre and the residential area, respectively, indicating that health effects of PM2.5 depend on urban environment as well as conditions, and emphasizing the importance of PN monitoring in terms of health effects related to local pollution sources.

Black carbon toxicity dependence on particle coating: Measurements with a novel cell exposure method.

Black carbon (BC) is a component of ambient particulate matter which originates from incomplete combustion emissions. BC is regarded as an important short-lived climate forcer, and a significant public health hazard. These two concerns have made BC a focus in aerosol science. Even though, the toxicity of BC particles is well recognized, the mechanism of toxicity for BC as a part of the total gas and particle emission mixture from combustion is still largely unknown and studies concerning it are scarce. In the present study, using a novel thermophoresis-based air-liquid interface (ALI) in vitro exposure system, we studied the toxicity of combustion-generated aerosols containing high levels of BC, diluted to atmospheric levels (1 to 10 µg/m3). Applying multiple different aerosol treatments, we simulated different sources and atmospheric aging processes, and utilizing several toxicological endpoints, we thoroughly examined emission toxicity. Our results revealed that an organic coating on the BC particles increased the toxicity, which was seen as larger genotoxicity and immunosuppression. Furthermore, aging of the aerosol also increased its toxicity. A deeper statistical analysis of the results supported our initial conclusions and additionally revealed that toxicity increased with decreasing particle size. These findings regarding BC toxicity can be applied to support policies and technologies to reduce the most hazardous compositions of BC emissions. Additionally, our study showed that the thermophoretic ALI system is both a suitable and useful tool for toxicological studies of emission aerosols.