The formation of unsaturated IrOx in SrIrO3 by cobalt-doping for acidic oxygen evolution reaction.

Electrocatalytic water splitting is a promising route for sustainable hydrogen production. However, the high overpotential of the anodic oxygen evolution reaction poses significant challenge. SrIrO3-based perovskite-type catalysts have shown great potential for acidic oxygen evolution reaction, but the origins of their high activity are still unclear. Herein, we develop a Co-doped SrIrO3 system to enhance oxygen evolution reaction activity and elucidate the origin of catalytic activity. In situ experiments reveal Co activates surface lattice oxygen, rapidly exposing IrOx active sites, while bulk Co doping optimizes the adsorbate binding energy of IrOx. The Co-doped SrIrO3 demonstrates high oxygen evolution reaction electrocatalytic activity, markedly surpassing the commercial IrO2 catalysts in both conventional electrolyzer and proton exchange membrane water electrolyzer.

Fe-Doped Ni2P/NiSe2 Composite Catalysts for Urea Oxidation Reaction (UOR) for Energy-Saving Hydrogen Production by UOR-Assisted Water Splitting.

The development of efficient urea oxidation reaction (UOR) catalysts helps UOR replace the oxygen evolution reaction (OER) in hydrogen production from water electrolysis. Here, we prepared Fe-doped Ni2P/NiSe2 composite catalyst (Fe-Ni2P/NiSe2-12) by using phosphating-selenizating and acid etching to increase the intrinsic activity and active areas. Spectral characterization and theoretical calculations demonstrated that electrons flowed through the Ni-P-Fe-interface-Ni-Se-Fe, thus conferring high UOR activity to Fe-Ni2P/NiSe2-12, which only needed 1.39 V vs RHE to produce the current density of 100 mA cm-2. Remarkably, this potential was 164 mV lower than that required for the OER under the same conditions. Furthermore, EIS demonstrated that UOR driven by the Fe-Ni2P/NiSe2-12 exhibited faster interfacial reactions, charge transfer, and current response compared to OER. Consequently, the Fe-Ni2P/NiSe2-12 catalyst can effectively prevent competition with OER and NSOR, making it suitable for efficient hydrogen production in UOR-assisted water electrolysis. Notably, when water electrolysis is operated at a current density of 40 mA cm-2, this UOR-assisted system can achieve a decrease of 140 mV in the potential compared to traditional water electrolysis. This study presents a novel strategy for UOR-assisted water splitting for energy-saving hydrogen production.

Co/Co3O4 Heterojunctions Encased in Porous N-Doped Carbon Nanocapsules for High-Performance Cathode of Rechargeable Zinc-Air Batteries.

A long-term goal of rechargeable zinc-air batteries (ZABs) has always been to design bifunctional electrocatalysts that are robust, effective, and affordable for the oxygen reduction reaction (ORR) and oxygen evolution reaction (OER). It has become a feasible method to construct metal/metal oxide interfaces to achieve superior electrocatalytic performance for ORR and OER by enhanced charge transfer. In this study, Co/Co3O4 heterojunctions were successfully prepared and encased in porous N-doped mesoporous carbon (Co/Co3O4@NC) via a simple condensation-carbonization-etching method. The extensive specific surface area of Co/Co3O4@NC facilitates effective interaction between the electrolyte and the catalyst, thereby enabling sufficient exposure of active sites for the ORR and the OER, consequently enhancing the rate of transport of active species. The well-designed Co/Co3O4@NC delivers superior ORR catalytic activity with a half-wave potential of 0.82 V (vs RHE) and a low overpotential of 347 mV at 10 mA cm-2 for OER in alkaline solution. The power density of Co/Co3O4@NC-based alkaline aqueous ZAB (156.5 mW cm-2) is superior to the commercial Pt/C + IrO2-based alkaline aqueous ZAB, and the cycling stability of ZAB is up to 220 h. In addition, Co/Co3O4@NC-based ZAB shows a high power density (50.1 mW cm-2). The construction of metal/metal oxide heterojunction encased in N-doped mesoporous carbon provides a novel route for the design of bifunctional electrocatalysts for high-performance ZABs.

Modulation Strategies for the Preparation of High-Performance Catalysts for Urea Oxidation Reaction and Their Applications.

Compared with the traditional electrolysis of water to produce hydrogen, urea-assisted electrolysis of water to produce hydrogen has significant advantages and has received extensive attention from researchers. Unfortunately, urea oxidation reaction (UOR) involves a complex six-electron transfer process leading to high overpotential, which forces researchers to develop high-performance UOR catalysts to drive the development of urea-assisted water splitting. Based on the UOR mechanism and extensive literature research, this review summarizes the strategies for preparing highly efficient UOR catalysts. First, the UOR mechanism is introduced and the characteristics of excellent UOR catalysts are pointed out. Aiming at this, the following modulation strategies are proposed to improve the catalytic performance based on summarizing various literature: 1) Accelerating the active phase formation to reduce initial potential; 2) Creating double active sites to trigger a new UOR mechanism; 3) Accelerating urea adsorption and promoting C─N bond cleavage to ensure the effective conduct of UOR; 4) Promoting the desorption of CO2 to improve stability and prevent catalyst poisoning; 5) Promoting electron transfer to overcome the inherent slow dynamics of UOR; 6) Increasing active sites or active surface area. Then, the application of UOR in electrochemical devices is summarized. Finally, the current deficiencies and future directions are discussed.

Recent progress in the synthesis of transition metal nitride catalysts and their applications in electrocatalysis.

Transition metal nitrides (TMNs) have become excellent substitutes for precious metals such as Pt and Ir in the field of electrocatalysis because of their excellent electrocatalytic performance, high conductivity, good corrosion resistance and stability. As we all know, the commonly utilized carbon-based materials corrode easily during electrocatalysis, which will lead to catalyst falling off and agglomeration. Compared with carbon-based materials, TMNs have stronger corrosion resistance and higher stability. In the metal nitrides, a variety of chemical bonds (metal bond, ionic bond and covalent bond) coexist, among which the ionic bond between metal atoms and nitrogen atoms can make the d-band shrink and narrow, which leads to TMNs having characteristics similar to precious metals in the electrocatalytic process; thus, they can be used as a substitute for precious metal catalysts. In this paper, the synthesis method and catalytic principle of transition metal nitrides and their applications in the fields of hydrogen evolution reaction (HER), oxygen evolution reaction (OER) and oxygen reduction reaction (ORR) are discussed, and the shortcomings of TMNs as a catalyst, the challenges faced in catalyst research and the developments and prospects for the future are pointed out.

Recent advances in the synthesis and electrocatalytic application of MXene materials.

MXenes are a class of two-dimensional materials with a graphene-like structure, which have excellent optical, biological, thermodynamic, electrical and magnetic properties. Due to the diversity resulting from the combination of transition metals and C/N, the MXene family has expanded to more than 30 members and been applied in many fields with broad application prospects. Among their applications, electrocatalytic applications have achieved many breakthroughs. Therefore, in this review, we summarize the reports on the preparation of MXenes and their application in electrocatalysis published in the last five years and describe the two main methods for the preparation of MXenes, i.e., bottom-up and top to bottom synthesis. Different methods may change the structure or surface termination of MXenes, and accordingly affect their electrocatalytic performance. Furthermore, we highlight the application of MXenes in the electrocatalytic hydrogen evolution reaction (HER), oxygen evolution reaction (OER), oxygen reduction reaction (ORR), carbon dioxide reduction reaction (CO2RR), nitrogen reduction reaction (NRR), and multi-functionalization. It can be concluded that the electrocatalytic properties of MXenes can be modified by changing the type of functional groups or doping. Also, MXenes can be compounded with other materials to produce electronic coupling and improve the catalytic activity and stability of the resulting composites. In addition, Mo2C and Ti3C2 are two types of MXene materials that have been widely studied in the field of electrocatalysis. At present, research on the synthesis of MXenes is focused on carbides, whereas research on nitrides is rare, and there are no synthesis methods meeting the requirements of green, safety, high efficiency and industrialization simultaneously. Therefore, it is very important to explore environmentally friendly industrial production routes and devote more research efforts to the synthesis of MXene nitrides.

Asymmetric Activation of the Nitro Group over a Ag/Graphene Heterointerface to Boost Highly Selective Electrocatalytic Reduction of Nitrobenzene.

The electrocatalytic reduction of nitrobenzene to aniline normally faces high overpotential and poor selectivity because of its six-electron redox nature. Herein, a Ag nanoparticles/laser-induced-graphene (LIG) heterointerface was fabricated on polyimide films and employed as an electrode material for an efficient nitrobenzene reduction reaction (NBRR) via a one-step laser direct writing technology. The first-principles calculations reveal that Ag/LIG shows the lowest activation barriers for the NBRR, which could be attributed to the optimum adsorption of the H atom realized by the appropriate interaction between Ag/LIG heterointerfaces and nitrobenzene. As a result, the overpotential of the NBRR is reduced by 217 mV after silver loading, and Ag/LIG shows a high aniline selectivity of 93%. Furthermore, an electrochemical reduction of nitrobenzene in tandem with an electrochemical oxidative polymerization of aniline was designed to serve as an alternative method to remove nitrobenzene from the aqueous solution. This strategy highlights the significance of heterointerfaces for efficient electrocatalysts, which may stimulate the development of novel electrocatalysts to boost the electrocatalytic activity.

Interfacial Fe-O-Ni-O-Fe Bonding Regulates the Active Ni Sites of Ni-MOFs via Iron Doping and Decorating with FeOOH for Super-Efficient Oxygen Evolution.

The integration of Fe dopant and interfacial FeOOH into Ni-MOFs [Fe-doped-(Ni-MOFs)/FeOOH] to construct Fe-O-Ni-O-Fe bonding is demonstrated and the origin of remarkable electrocatalytic performance of Ni-MOFs is elucidated. X-ray absorption/photoelectron spectroscopy and theoretical calculation results indicate that Fe-O-Ni-O-Fe bonding can facilitate the distorted coordinated structure of the Ni site with a short nickel-oxygen bond and low coordination number, and can promote the redistribution of Ni/Fe charge density to efficiently regulate the adsorption behavior of key intermediates with a near-optimal d-band center. Here the Fe-doped-(Ni-MOFs)/FeOOH with interfacial Fe-O-Ni-O-Fe bonding shows superior catalytic performance for OER with a low overpotential of 210 mV at 15 mA cm-2 and excellent stability with ≈3 % attenuation after a 120 h cycle test. This study provides a novel strategy to design high-performance Ni/Fe-based electrocatalysts for OER in alkaline media.

Surface-Adsorbed Carboxylate Ligands on Layered Double Hydroxides/Metal-Organic Frameworks Promote the Electrocatalytic Oxygen Evolution Reaction.

Metal-organic frameworks (MOFs) with carboxylate ligands as co-catalysts are very efficient for the oxygen evolution reaction (OER). However, the role of local adsorbed carboxylate ligands around the in-situ-transformed metal (oxy)hydroxides during OER is often overlooked. We reveal the extraordinary role and mechanism of surface-adsorbed carboxylate ligands on bi/trimetallic layered double hydroxides (LDHs)/MOFs for OER electrocatalytic activity enhancement. The results of X-ray photoelectron spectroscopy (XPS), synchrotron X-ray absorption spectroscopy, and density functional theory (DFT) calculations show that the carboxylic groups around metal (oxy)hydroxides can efficiently induce interfacial electron redistribution, facilitate an abundant high-valence state of nickel species with a partially distorted octahedral structure, and optimize the d-band center together with the beneficial Gibbs free energy of the intermediate. Furthermore, the results of in situ Raman and FTIR spectra reveal that the surface-adsorbed carboxylate ligands as Lewis base can promote sluggish OER kinetics by accelerating proton transfer and facilitating adsorption, activation, and dissociation of hydroxyl ions (OH- ).

Hierarchical porous Ni, Fe-codoped Co-hydroxide arrays derived from metal-organic-frameworks for enhanced oxygen evolution.

The multi metal organic frameworks (BTC-CoNiFeZn) were used as the precursors of in situ structure reconstruction in alkaline solution, and we synthesized hierarchical porous Ni,Fe-codoped Co-hydroxide nanowire array (Ni0.8Fe0.2/Co-H NAs/NF) catalyst for the oxygen evolution reaction (OER). Benefiting from the rational micro-structure, rich ion-accessible nanopores, and abundant defect sites, the target catalysts possess enhanced intrinsic activity. The obtained Ni0.8Fe0.2/Co-H NAs/NF catalysts show superior OER catalytic activity with a low overpotential of 231 mV at 10 mA cm-2, a small Tafel slope of 32.9 mV dec-1, and high cycle stability for 135 h with performance degradation of only about 4.4%.

Correction: Super-large dendrites composed of trigonal PbO2 nanoplates with enhanced performances for electrochemical devices.

Correction for 'Super-large dendrites composed of trigonal PbO2 nanoplates with enhanced performances for electrochemical devices' by Liang-Xin Ding et al., Chem. Commun., 2012, 1275-1277, DOI: 10.1039/C2CC15271A.

Correction: Cu2O template synthesis of high-performance PtCu alloy yolk-shell cube catalysts for direct methanol fuel cells.

Correction for 'Cu2O template synthesis of high-performance PtCu alloy yolk-shell cube catalysts for direct methanol fuel cells' by Sheng-Hua Ye et al., Chem. Commun., 2014, 50, 12337-12340, DOI: 10.1039/C4CC04108A.

Boosting Lattice Oxygen Oxidation of Perovskite to Efficiently Catalyze Oxygen Evolution Reaction by FeOOH Decoration.

In the process of oxygen evolution reaction (OER) on perovskite, it is of great significance to accelerate the hindered lattice oxygen oxidation process to promote the slow kinetics of water oxidation. In this paper, a facile surface modification strategy of nanometer-scale iron oxyhydroxide (FeOOH) clusters depositing on the surface of LaNiO3 (LNO) perovskite is reported, and it can obviously promote hydroxyl adsorption and weaken Ni-O bond of LNO. The above relevant evidences are well demonstrated by the experimental results and DFT calculations. The excellent hydroxyl adsorption ability of FeOOH-LaNiO3 (Fe-LNO) can obviously optimize OH- filling barriers to promote lattice oxygen-participated OER (LOER), and the weakened Ni-O bond of LNO perovskite can obviously reduce the reaction barrier of the lattice oxygen participation mechanism (LOM). Based on the above synergistic catalysis effect, the Fe-LNO catalyst exhibits a maximum factor of 5 catalytic activity increases for OER relative to the pristine perovskite and demonstrates the fast reaction kinetics (low Tafel slope of 42 mV dec-1) and superior intrinsic activity (TOFs of ~40 O2 S-1 at 1.60 V vs. RHE).

Structural evolution from a fence-like to pillared-layer metal-organic framework for the stable oxygen evolution reaction.

A stable pillared-layer metal-organic framework (MOF) was obtained through post-synthesis modification from an unstable fence-like MOF for the first time. By virtue of high exposure of active sites on the layers, the evolved MOF with Fe doping exhibits an ultralow overpotential of 238 mV at 10 mA cm-2 during the oxygen evolution reaction (OER). Moreover, it shows a superior electrocatalytic stability with almost no attenuation for more than 168 h.

Engineering cobalt oxide by interfaces and pore architectures for enhanced electrocatalytic performance for overall water splitting.

The development of efficient electrocatalysts for overall water splitting is important for future renewable energy systems. Herein, macroporous CoO covered by Co/N-doped graphitic carbon nanosheet arrays (mac-CoO@Co/NGC NSAs) were constructed by engineering a mesoporous CoO nanowire (mes-CoO NWAs) core with highly conductive Co nanoparticles coated by a N-doped graphitic carbon (Co/NGC) shell. The in situ derived Co/NGC shell not only introduces electrocatalytic active sites for the hydrogen evolution reaction (HER) but also promotes the oxygen evolution reaction (OER) through the strong interaction between the CoO core and the Co/NGC shell. Moreover, the highly conductive Co/NGC shell crosslinks the isolated mesoporous CoO nanowires into a nanosheet rich in macropores, ensuring effective electron and mass transfer. Furthermore, the chemically stable N-doped graphitic carbon layer and physically stable hierarchical nanosheet arrays ensure the stability of the catalyst. Owing to the desirable interfaces and pore architecture, the as-prepared mac-CoO@Co/NGC NSAs can serve as highly effective, binder-free electrocatalysts for overall water splitting with a stable cell voltage of 1.62 V at 10 mA cm-2 for 35 h.

Boosting the electrocatalytic performance of NiFe layered double hydroxides for the oxygen evolution reaction by exposing the highly active edge plane (012).

The intrinsic activity of NiFe layer double hydroxides (LDHs) for the oxygen evolution reaction (OER) suffers from its predominantly exposed (003) basal plane, which is thought to have poor activity. Herein, we construct a hierarchal structure of NiFe LDH nanosheet-arrays-on-microplates (NiFe NSAs-MPs) to elevate the electrocatalytic activity of NiFe LDHs for the OER by exposing a high-activity plane, such as the (012) edge plane. It is surprising that the NiFe NSAs-MPs show activity of 100 mA cm-2 at an overpotential (η) of 250 mV, which is five times higher than that of (003) plane-dominated NiFe LDH microsheet arrays (NiFe MSAs) at the same η, representing the excellent electrocatalytic activity for the OER in alkaline media. Besides, we analyzed the OER activities of the (003) basal plane and the (012) and (110) edge planes of NiFe LDHs by density functional theory with on-site Coulomb interactions (DFT+U), and the calculation results indicated that the (012) edge plane exhibits the best catalytic performance among the various crystal planes because of the oxygen coordination of the Fe site, which is responsible for the high catalytic activity of NiFe NSAs-MPs.

Ni3S2 in Situ Grown on Ni Foam Coupled with Nitrogen-Doped Carbon Nanotubes as an Efficient Electrocatalyst for the Hydrogen Evolution Reaction in Alkaline Solution.

Searching for a highly efficient electrocatalyst for the hydrogen evolution reaction (HER) in alkaline solution is still challenging. In this work, we report a HER electrocatalyst composed of Ni foam, Ni3S2, and nitrogen-doped carbon nanotubes (NF@Ni3S2@NCNTs). The good lattice matching between Ni and Ni3S2, interstitial doping of C and N atoms, and synergistic effect of NCNTs make NF@Ni3S2@NCNTs highly efficient HER electrocatalysts in alkaline solution. NF@Ni3S2@NCNTs exhibit an overpotential of 93.89 mV at a current density of 10 mA cm-2, a Tafel slope of 54 mV dec-1, and superior stability for HER in 1 M KOH solution. Our findings will promote the reasonable design and synthesis of an efficient electrocatalyst for HER in alkaline electrolytes.